The EV mode signal is sent to the hybrid vehicle control ECU. This signal is then transmitted from the hybrid vehicle control ECU via CAN to the combination meter sub-assembly to illuminate the EV indicator light.
If any of the following conditions are not met, EV mode may not be turned on or the mode may be canceled. (A buzzer sounds to indicate that the transition to EV mode is canceled.)
| EV Mode Entry Condition | Tester Display | Specified Condition |
|---|---|---|
| HV battery charge level | State of Charge (All Bat) | Approximately 50% or higher |
| Accelerator pedal position | Accelerator Degree | Below approximately 30% |
| Engine coolant temperature | Engine Coolant Temp | 0°C (32°F) or higher |
| HV battery temperature | Temp of Batt TB1 to TB3 | Between 10 to 40°C (50 to 104°F) |
| Vehicle speed
(Varies depending on engine warm-up condition) |
Vehicle Spd | Cold: 30 km/h (19 mph) or less
Warmed-up: 45 km/h (28 mph) |
| Win | Charge Control Value | Below -20 kW |
| Wout | Discharge Control Value | 20 kW or higher |
| Defroster | - | OFF |
| Cruise control | - | OFF |
Check if a buzzer sounded when attempting to enter EV mode.
| Result | Proceed to |
|---|---|
| No buzzer sounded. | A |
| A buzzer sounded. | B |
If a buzzer sounds, one or more of the EV mode entry conditions have not been met. Check that all of the EV mode entry conditions have been met before pressing the EV drive mode switch (Combination Switch Assembly).
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / CAN Bus Check.
| Result | Proceed to |
|---|---|
| All of the ECUs and sensors that are currently connected to the CAN communication system are displayed. | A |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
(w/ Central Gateway ECU) |
B |
| None of the ECUs and sensors that are currently connected to the CAN communication system are displayed, or some of them are not displayed.
(w/o Central Gateway ECU) |
C |
Turn the power switch off.
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: System Select / Health Check.
Check DTCs.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs are output. | B |
Turn the power switch off.
A
B
Connect the GTS to the DLC3.
Turn the power switch on (READY).
Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. EV Mode.
Perform the "Indicat. EV Mode" Active Test.
The EV mode indicator light comes on or blinks.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (w/o Multi-information Display) | B |
| NG (w/ Multi-information Display) | C |
Turn the power switch off.
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List / EV request, EV Switch.
Read the value displayed on the GTS.
| Tester Display | Measurement Item/Range | Normal Condition |
|---|---|---|
| EV request | EV mode transition availability/
ON or OFF |
In EV mode: ON |
| EV Switch | EV drive mode switch (Combination Switch Assembly) condition/
ON or OFF |
EV drive mode switch (Combination Switch Assembly) being pushed and held: ON |
| Result | Proceed to |
|---|---|
| The GTS display changes according to the EV drive mode switch (Combination Switch Assembly) operation. | A |
| The GTS display does not change according to the EV drive mode switch (Combination Switch Assembly) operation. | B |
Turn the power switch off.
A
B
Remove the EV drive mode switch (combination switch assembly).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 7 (S) - 3 (E) | EV drive mode switch (Combination Switch Assembly) being pushed and held | Below 1 Ω |
| EV drive mode switch (Combination Switch Assembly) not pushed | 10 kΩ or higher |
| *a | Component without harness connected
(EV Drive Mode Switch (Combination Switch Assembly)) |
Install the EV drive mode switch (combination switch assembly).
OK
NG
Disconnect the L143 EV drive mode switch (combination switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L143-3 (E) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector
(to EV Drive Mode Switch (Combination Switch Assembly)) |
Reconnect the L143 EV drive mode switch (combination switch assembly) connector.
OK
NG
Disconnect the L5 hybrid vehicle control ECU connector.
Disconnect the L143 EV drive mode switch (combination switch assembly) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L5-15 (EVSW) - L143-7 (S) | Always | Below 1 Ω |
| L5-15 (EVSW) or L143-7 (S) - Body ground | Always | 10 kΩ or higher |
| *a | Rear view of wire harness connector
(to Hybrid Vehicle Control ECU) |
| *b | Front view of wire harness connector
(to EV Drive Mode Switch (Combination Switch Assembly)) |
Reconnect the L143 EV drive mode switch (combination switch assembly) connector.
Reconnect the L5 hybrid vehicle control ECU connector.
OK
NG