Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM J

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  Pattern Select Switch Eco Mode Circuit  


DESCRIPTION

When selecting ECO mode, the ECO mode switch (combination switch assembly) operation signal is sent to the air conditioning amplifier assembly. Following this, ECO mode control is activated for the heater and air conditioning system.

WIRING DIAGRAM

A254642E57
4.479,3.771 4.927,3.969 0.448,0.198 10 false L17 4.49,3.938 6.719,4.292 2.229,0.354 10 false Air Conditioning Amplifier Assembly 5.146,2.844 5.76,3.042 0.615,0.198 10 false ECOS 4.875,2.719 5.146,3 0.271,0.281 10 false 15 1.531,3.354 1.906,3.563 0.375,0.208 10 false L143 1.531,3.521 3.521,4 1.99,0.479 10 false ECO Mode Switch (Combination Switch Assembly) 1.833,2.729 2.219,3 0.385,0.271 10 false E 1.635,2.729 1.958,3.021 0.323,0.292 10 false 3 3.25,2.719 3.625,2.927 0.375,0.208 10 false 5 2.865,2.719 3.281,2.906 0.417,0.188 10 false ECU 0.969,1.229 2.167,1.635 1.198,0.406 10 false Combination Meter Sub-assembly 3.021,1.229 4.271,1.688 1.25,0.458 10 false Power Management Control ECU 0.594,4.396 2.354,4.646 1.76,0.25 10 false : CAN Communication

PROCEDURE

2.CHECK DTC OUTPUT (HEALTH CHECK)

A

3.PERFORM ACTIVE TEST USING GTS (INDICAT. ECO MODE)

B

GO TO DTC CHART

3.PERFORM ACTIVE TEST USING GTS (INDICAT. ECO MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Combination Meter / Active Test / Indicat. ECO Mode.


d.

Perform the "Indicat. ECO MODE" Active Test.

OK:

The ECO MODE indicator light comes on or blinks.



e.

Turn the power switch off.



OK

4.READ VALUE USING GTS (ECO MODE)

NG

4.READ VALUE USING GTS (ECO MODE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / ECO Mode.


d.

Read the value displayed on the GTS.

Tester Display Measurement Item/Range Normal Condition
ECO Mode ECO mode transition availability/
ON or OFF
In ECO mode: ON

Result:
Result Proceed to
The GTS display changes according to the ECO mode switch (combination switch assembly) operation. A
The GTS display does not changes according to the ECO mode switch (combination switch assembly) operation. B



e.

Turn the power switch off.



A

B

5.READ VALUE USING GTS (ECO SWITCH)
5.READ VALUE USING GTS (ECO SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Air Conditioning / Data List / ECO Switch.


d.

Read the value displayed on the GTS.

Tester Display Measurement Item/Range Normal Condition
ECO Switch ECO switch condition/
ON or OFF
ECO switch being pushed and held: ON
ECO switch not pushed: OFF

Result:
Result Proceed to
The GTS display changes according to the ECO mode switch (combination switch assembly) operation. A
The GTS display does not changes according to the ECO mode switch (combination switch assembly) operation. B



e.

Turn the power switch off.



A

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

B

6.CHECK ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY)
6.CHECK ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY)
a.

Remove the ECO mode switch (combination switch assembly).


b.
A253200E19
0.635,0.173 0.786,0.334 0.151,0.161 10 *a 2.178,1.737 2.505,1.898 0.327,0.161 10 ECU 1.298,1.737 1.407,1.898 0.110,0.161 10 E 1.996,1.225 2.312,1.721 false 1.642,1.039 1.373,1.731 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
5 (ECU) - 3 (E) ECO mode switch (combination switch assembly) being pushed and held Below 1 Ω
ECO mode switch (combination switch assembly) not pushed 10 kΩ or higher



Text in Illustration
*a Component without harness connected
(ECO Mode Switch (Combination Switch Assembly))

c.

Install the ECO mode switch (combination switch assembly).



OK

7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)

NG

REPLACE ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY)

7.CHECK HARNESS AND CONNECTOR (ECO MODE SWITCH (COMBINATION SWITCH ASSEMBLY) - BODY GROUND)
a.

Disconnect the L143 ECO mode switch (combination switch assembly) connector.


b.
U190675E02
1.854,1.177 2.104,1.823 true 1.042,0.271 1.198,0.438 0.156,0.167 10 false *a 2.083,1.844 2.198,2.01 0.115,0.167 10 false E 0.813,1.042 1.146,1.208 0.333,0.167 10 false L143

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L143-3 (E) - Body ground Always Below 1 Ω



Text in Illustration
*a Front view of wire harness connector
(to ECO Mode Switch (Combination Switch Assembly))

c.

Reconnect the L143 ECO mode switch (combination switch assembly) connector.



OK

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (COMBINATION SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY - ECO MODE SWITCH (COMBINATION SWITCH)
a.

Disconnect the L17 air conditioning amplifier assembly connector.


b.

Disconnect the L143 ECO mode switch (combination switch assembly) connector.


c.
U190678E02
2.625,1.688 2.75,2.219 true 1.448,3.677 1.323,4.125 true 0.073,0.073 0.229,0.219 0.156,0.146 10 false *a 0.927,2.635 1.083,2.781 0.156,0.146 10 false *b 1.188,1.625 1.448,1.771 0.26,0.146 10 false L17 2.521,2.229 2.938,2.375 0.417,0.146 10 false ECOS 1.125,4.135 1.448,4.281 0.323,0.146 10 false ECU 0.448,3.438 0.781,3.604 0.333,0.167 10 false L143

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L17-15 (ECOS) - L143-5 (ECU) Always Below 1 Ω
L17-15 (ECOS) or L143-5 (ECU) - Body ground Always 10 kΩ or higher



Text in Illustration
*a Front view of wire harness connector
(to Air Conditioning Amplifier Assembly)
*b Front view of wire harness connector
(to ECO Mode Switch (Combination Switch Assembly))

d.

Reconnect the L143 ECO mode switch (combination switch assembly) connector.


e.

Reconnect the L17 air conditioning amplifier assembly connector.



OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR