Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0069-273  Manifold Absolute Pressure - Barometric Pressure Correlation  


DESCRIPTION

The atmospheric pressure sensor mounted on the MG ECU circuit board detects the atmospheric pressure. This reading is used to perform system control that considers vehicle usage conditions.

A379089E01
0.635,0.719 2.979,1.25 2.344,0.531 10 false Power Management Control ECU 1.542,2.292 2.323,2.646 0.781,0.354 10 false ECM 0.792,3.146 2.323,3.438 1.531,0.292 10 false CAN Communication 0.781,3.448 2.344,3.74 1.563,0.292 10 false Serial Communication 4.438,0.167 6.594,0.563 2.156,0.396 10 false Inverter With Converter Assembly 4.448,0.542 6.438,1.052 1.99,0.51 10 false MG ECU (Atmosphere Pressure Sensor) 4.542,1.25 6.521,1.615 1.979,0.365 10 false Atmosphere Pressure Sensor 4.271,2.021 6.479,2.792 2.208,0.771 10 false Manifold Absolute Pressure Sensor Assembly (Intake Air Surge Tank Assembly)

DTC No. INF Code DTC Detection Condition Trouble Area
P0069 273 Difference between the atmospheric pressure value of the atmospheric pressure sensor in the inverter with converter assembly and the manifold absolute pressure sensor (for EGR control) exceeds a specified value. The same condition recurs within 3 hours when driving in EV mode.
·

Inverter with converter assembly

·

Manifold absolute pressure sensor

·

ECM

·

Wire harness or connector



WIRING DIAGRAM

A259008E01
0.147,2.605 0.456,2.802 0.309,0.198 10 D3 0.14,2.773 2.379,2.922 2.239,0.149 10 Manifold Absolute Pressure Sensor 6.185,3.099 6.529,3.261 0.343,0.163 10 ECM 5.632,0.98 6.080,1.128 0.448,0.149 10 VCPM 5.877,3.099 6.158,3.248 0.281,0.149 10 D28 5.371,0.98 5.548,1.128 0.177,0.149 10 72 5.371,1.554 5.558,1.724 0.187,0.170 10 69 5.371,2.093 5.575,2.242 0.204,0.149 10 71 5.632,1.554 5.899,1.703 0.267,0.149 10 PIM 5.632,2.093 6.045,2.260 0.413,0.166 10 EPIM 1.366,0.98 1.591,1.128 0.225,0.149 10 VC 1.324,1.554 1.591,1.703 0.267,0.149 10 PIM 1.394,2.093 1.592,2.260 0.198,0.166 10 E2 1.664,0.98 1.771,1.149 0.107,0.170 10 3 1.664,1.554 1.764,1.724 0.100,0.170 10 1 1.664,2.093 1.785,2.256 0.121,0.163 10 2

CAUTION / NOTICE / HINT

HINT:

After the repair, perform the following procedure to confirm the repair.

·

If the values of Data List items "Atmosphere Pressure" and "MAP" are almost the same with the engine stopped and the power switch on (IG), those sensors are normal.

·

If the values of Data List items "Atmosphere Pressure" and "MAP" are still difference 10 kPa or more after after replacing components of the inverter with converter assembly, replace the inverter with converter assembly.



PROCEDURE

1.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Fully depress the accelerator pedal for 5 seconds to start the engine and keep it running.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
DTCs other than those listed in the following table are output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0107 Manifold Absolute Pressure/Barometric Pressure Circuit Low Input
P0108 Manifold Absolute Pressure/Barometric Pressure Circuit High Input

HINT:

P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.



f.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0069-273 only is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A1A-151, 155, 156, 658, 659 Generator Control Module
P0A1B-193, 512, 661, 786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P2228-268 Barometric Pressure Sensor "A" Circuit Low
P2229-269 Barometric Pressure Sensor "A" Circuit High
P2511-149 HV CPU Power Relay Sensor Circuit Intermittent No Continuity
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0100-211, 530 Lost Communication with ECM/PCM "A"
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0069-273 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

3.READ VALUE USING GTS (MAP, ATMOSPHERE PRESSURE)

B

3.READ VALUE USING GTS (MAP, ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.


d.

Using the table, read the normal atmospheric pressure value for the applicable altitude.

A250945


e.

Compare the MAP and Atmosphere Pressure values in the Data List with the normal atmospheric value from the table.

Result:
Result Proceed to
Other than the following. A
Difference between MAP in Data List and normal atmospheric pressure value is 10 kPa or more. B
Difference between Atmosphere Pressure in Data List and normal atmospheric pressure value is 10 kPa or more. C



f.

Turn the power switch off.



A

4.READ VALUE USING GTS (MAP)

B

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

4.READ VALUE USING GTS (MAP)
a.

Push the P position switch.


b.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP


c.

Read the MAP value in the Data List with the engine stopped.


d.

While depressing the brake pedal, turn the power switch on (READY).


e.

With the READY indicator light illuminated, fully depress the accelerator pedal.


f.

Read the MAP value in the Data List with the engine running.


g.

Compare the MAP value noted with the engine stopped and the MAP value noted with the engine running.

OK:

The MAP value changes (pressure decreases when the engine is started).



h.

Turn the power switch off.



OK

5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NG

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
5.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT

6.READ VALUE USING GTS (MAP, ATMOSPHERE PRESSURE)
6.READ VALUE USING GTS (MAP, ATMOSPHERE PRESSURE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / MAP, Atmosphere Pressure.


d.

Compare the Data List item "MAP" with "Atmosphere Pressure".

Result:
Result Proceed to
The difference between "MAP" and "Atmosphere Pressure" is 10 kPa or more. A
The difference between "MAP" and "Atmosphere Pressure" is less than 10 kPa. B



e.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B

COMPLETED

7.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR)
a.

Disconnect the D3 manifold absolute pressure sensor connector.


b.

Turn the power switch on (IG).


c.
U110451E02
1.469,2.281 1.24,2.802 false 1.885,2.292 2,2.823 false 1.177,2.26 0.719,2.802 false 0.156,0.031 0.354,0.24 0.198,0.208 10 false *a 1.146,2.844 1.396,3.042 0.25,0.198 10 false E2 1.906,2.844 2.156,3.042 0.25,0.198 10 false VC 0.521,2.833 0.813,3.031 0.292,0.198 10 false PIM 0.323,1.938 0.604,2.115 0.281,0.177 10 false D3

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D3-3 (VC) - D3-2 (E2) Power switch on (IG) 4.5 to 5.5 V
D3-1 (PIM) - D3-2 (E2) Power switch on (IG) 3.0 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)

Result:
Result Proceed to
NG A
OK B



d.

Reconnect the D3 manifold absolute pressure sensor connector.



A

8.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

B

9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR
8.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
a.

Disconnect the D3 manifold absolute pressure sensor connector.


b.

Disconnect the D28 ECM connector.


c.
U154480E01
1.599,0.154 1.793,0.335 0.195,0.181 10 D3 1.586,2.482 1.857,2.663 0.272,0.181 10 D28 0.084,0.02 0.265,0.207 0.180,0.187 10 *a 0.084,2.269 0.265,2.457 0.180,0.187 10 *b 2.117,1.996 2.355,2.153 0.238,0.156 10 VC 1.492,1.996 1.730,2.153 0.238,0.156 10 E2 0.807,1.996 1.150,2.153 0.342,0.156 10 PIM 1.297,1.637 0.987,1.975 false 1.591,1.637 1.591,1.975 false 1.891,1.637 2.201,1.975 false 1.79,4.15 2.220,4.306 0.430,0.156 10 VCPM 1.079,4.15 1.475,4.306 0.396,0.156 10 EPIM 0.566,4.15 0.909,4.306 0.342,0.156 10 PIM 1.145,3.595 0.746,4.128 false 1.298,3.595 1.298,4.131 false 1.377,3.595 1.96,4.128 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D3-3 (VC) - D28-72 (VCPM) Always Below 1 Ω
D3-2 (E2) - D28-71 (EPIM) Always Below 1 Ω
D3-1 (PIM) - D28-69 (PIM) Always Below 1 Ω
D3-3 (VC) or D28-72 (VCPM) - Body ground Always 10 kΩ or higher
D3-2 (E2) or D28-71 (EPIM) - Body ground Always 10 kΩ or higher
D3-1 (PIM) or D28-69 (PIM) - Body ground Always 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
*b Front view of wire harness connector
(to ECM)


d.

Reconnect the D28 ECM connector.


e.

Reconnect the D3 manifold absolute pressure sensor connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR

NEXT

10.CLEAR DTC
10.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

11.CHECK DTC OUTPUT (HYBRID CONTROL)
11.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0069-273 is not output. A
DTC P0069-273 is output. B



e.

Turn the power switch off.



A

COMPLETED

B