The power management control ECU compares the engine speed sent from the ECM via CAN communication and the engine speed that is indicated by pulses sent from the ECM. If the pulse input is not normal, the power management control ECU sets this DTC.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0340 | 886 | Malfunction in the engine speed sensor (GI signal) circuit | ·
Wire harness or connector ·
No. 1 crank position sensor (Camshaft position sensor) ·
Inverter with converter assembly ·
ECM ·
Power management control ECU |
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals of the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (READY).
With the vehicle stopped, push the P position switch (transmission shift main switch).
Depress the accelerator pedal to start the engine.
Depress the accelerator pedal and maintain the engine speed at 1000 rpm or more for 5 seconds or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P0340-886 only is output. | A |
| P0343-747 is also output. | B |
Turn the power switch off.
A
B
Check the connector connections and contact pressure of the relevant terminals for the ECM connectors (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.
The connectors are connected securely and there are no contact pressure problems.
When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.
OK
NG
Check the connector connections and contact pressure of the relevant terminals for the power management control ECU connectors (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
| *A | for LHD | *B | for RHD |
The connectors are connected securely and there are no contact pressure problems.
OK
NG
Connect an oscilloscope between the power management control ECU terminals specified in the table below.
Turn the power switch on (READY).
Measure the waveform.
| Item | Content |
|---|---|
| Terminal | A21-16 (GI) - L5-6 (E1) |
| Equipment Setting | 5 V/DIV., 20 ms./DIV. |
| Condition | Power switch on (READY) with engine running |
| *a | Component with harness connected
(Power Management Control ECU) |
| Result | Proceed to |
|---|---|
| Normal | A |
| Waveform is flat, and is stuck on the +B side. | B |
| Waveform is flat, and is stuck on the GND side. | C |
A
B
C
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the D28 ECM connector.
Disconnect the A59 inverter with converter assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D28-48 (G2O) - Body ground | Power switch on (IG) | 11 to 14 V |
| *a | Front view of wire harness connector
(to ECM) |
Turning the power switch on (IG) with the ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the A59 inverter with converter assembly connector.
Reconnect the D28 ECM connector.
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the D28 ECM connector.
Disconnect the A21 power management control ECU connector.
Disconnect the A59 inverter with converter assembly connector.
Connect the cable to the negative (-) auxiliary battery terminal.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D28-48 (G2O) or A21-16 (GI) - Body ground | Power switch on (IG) | Below 1 V |
| *a | Front view of wire harness connector
(to ECM) |
| *b | Rear view of wire harness connector
(to Power Management Control ECU) |
Turning the power switch on (IG) with the inverter with converter assembly connector, power management control ECU connector and ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D28-48 (G2O) or A21-16 (GI)- Body ground | Power switch off | 10 kΩ or higher |
Disconnect the cable from the negative (-) auxiliary battery terminal.
Reconnect the D28 ECM connector.
Reconnect the A21 power management control ECU connector.
Reconnect the A59 inverter with converter assembly connector.
OK
NG
Disconnect all the connectors from the power management control ECU.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-16 (GI) - L5-6 (E1) | Always | 10 kΩ or higher |
| *a | Component without harness connected
(Power Management Control ECU) |
Reconnect the power management control ECU connectors.
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the A59 inverter with converter assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A59-29 (GI) - A59-28 (GND1) | Power switch off | 10 kΩ or higher |
| *a | Component without harness connected
(Inverter with Converter Assembly) |
Reconnect the A59 inverter with converter assembly connector.
OK
NG