Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0340-886  Camshaft Position Sensor "A" Circuit  


DESCRIPTION

The hybrid vehicle control ECU compares the engine speed sent from the ECM via CAN communication and the engine speed that is indicated by pulses sent from the ECM. If the pulse input is not normal, the hybrid vehicle control ECU sets this DTC.

DTC No. INF Code DTC Detection Condition Trouble Area
P0340 886 Malfunction in the engine speed sensor (GI signal) circuit
·

Wire harness or connector

·

No. 1 crank position sensor (Camshaft position sensor)

·

Inverter with converter assembly

·

ECM

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A254872E10
2.656,5.271 3.083,5.448 0.427,0.177 10 false A59 2.667,5.438 4.833,5.615 2.167,0.177 10 false Inverter with Converter Assembly 3.844,4.344 4.063,4.51 0.219,0.167 10 false GI 4.073,4.323 4.292,4.49 0.219,0.167 10 false 29 2.969,4.75 3.396,4.917 0.427,0.167 10 false GND1 2.75,4.656 2.969,4.823 0.219,0.167 10 false 28 2.25,2.823 2.677,3 0.427,0.177 10 false D28 2.25,2.99 2.646,3.167 0.396,0.177 10 false ECM 2.281,2.188 2.479,2.365 0.198,0.177 10 false E1 1.917,2.083 2.344,2.26 0.427,0.177 10 false 104 0.031,1.635 1.833,2.042 1.802,0.406 10 false No. 1 Crank Position Sensor (Camshaft Position Sensor) 2.771,1.302 3.01,1.542 0.24,0.24 10 false IC 4.594,1.104 4.792,1.281 0.198,0.177 10 false 48 4.188,1.104 4.521,1.281 0.333,0.177 10 false G2O 5.333,1.229 5.625,1.385 0.292,0.156 10 false A21 5.375,1.042 5.625,1.229 0.25,0.188 10 false 10 5.417,1.99 5.667,2.177 0.25,0.188 10 false 6 5.375,2.188 5.667,2.344 0.292,0.156 10 false L5 5.677,1.135 5.885,1.313 0.208,0.177 10 false GI 5.698,2.167 5.906,2.344 0.208,0.177 10 false E1 5.563,2.813 6.958,3.146 1.396,0.333 10 false Hybrid Vehicle Control ECU 3.625,4.698 4.052,4.865 0.427,0.167 10 false DRN5 4.073,4.615 4.292,4.781 0.219,0.167 10 false 30

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals of the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY).

2.

With the vehicle stopped, push the P position switch (transmission shift main switch).

3.

Depress the accelerator pedal to start the engine.

4.

Depress the accelerator pedal and maintain the engine speed at 1000 rpm or more for 5 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
P0340-886 only is output. A
P0343-747 is also output. B



e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)

B

7.CHECK HARNESS AND CONNECTOR (ECM - HYBRID VEHICLE CONTROL ECU, INVERTER WITH CONVERTER ASSEMBLY)
2.CHECK CONNECTOR CONNECTION CONDITION (ECM CONNECTOR)
a.
A253292

Check the connector connections and contact pressure of the relevant terminals for the ECM connectors (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

NOTICE:

Before disconnecting the connector, confirm that it is properly connected by checking that the locking claws are engaged and that the connector does not pull out.


OK:

The connectors are connected securely and there are no contact pressure problems.


HINT:

When connecting the connector, insert it with the locking lever in the raised position. Rotate the lever downward and make sure that the connector is pulled into its socket. When the locking lever is in its fully closed position, a click will be heard as its locking claws engage. After the click is heard, pull up on the connector to confirm that it is properly connected.




OK

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)

NG

CONNECT SECURELY

3.CHECK CONNECTOR CONNECTION CONDITION (HYBRID VEHICLE CONTROL ECU CONNECTOR)
a.

Check the connector connections and contact pressure of the relevant terminals for the hybrid vehicle control ECU connectors (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).

A279789E01
0.14,0.122 0.317,0.274 0.177,0.152 10 *A 3.783,0.122 3.960,0.274 0.177,0.152 10 *B

Text in Illustration
*A for LHD *B for RHD

OK:

The connectors are connected securely and there are no contact pressure problems.




OK

4.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)

NG

CONNECT SECURELY

4.CHECK HYBRID VEHICLE CONTROL ECU (CHECK WAVEFORM)
a.

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below.


b.

Turn the power switch on (READY).


c.
U190564E02
0.927,1.375 0.531,1.823 false 1.833,1.302 1.781,1.906 false 0.125,0.146 0.344,0.365 0.219,0.219 10 false *a 0.438,1.833 0.958,1.99 0.521,0.156 10 false GI 1.729,1.917 1.938,2.083 0.208,0.167 10 false E1 2.99,3.542 3.354,3.719 0.365,0.177 10 false GND 0.719,0.667 0.99,0.833 0.271,0.167 10 false A21 1.99,0.667 2.26,0.833 0.271,0.167 10 false L5

Measure the waveform.

Item Content
Terminal A21-10 (GI) - L5-6 (E1)
Equipment Setting 5 V/DIV., 20 ms./DIV.
Condition Power switch on (READY) with engine running


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)

Result:
Result Proceed to
Normal A
Waveform is flat, and is stuck on the +B side. B
Waveform is flat, and is stuck on the GND side. C



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU)

C

7.CHECK HARNESS AND CONNECTOR (ECM - HYBRID VEHICLE CONTROL ECU, INVERTER WITH CONVERTER ASSEMBLY)
5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D28 ECM connector.


c.

Disconnect the A59 inverter with converter assembly connector.


d.

Connect the cable to the negative (-) auxiliary battery terminal.


e.

Turn the power switch on (IG).


f.
U154337E03
0.76,1.115 0.948,1.885 false 0.135,0.063 0.417,0.229 0.281,0.167 10 false *a 0.792,1.896 1.104,2.094 0.313,0.198 10 false G2O 1.479,0.24 1.75,0.406 0.271,0.167 10 false D28

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D28-48 (G2O) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)

NOTICE:

Turning the power switch on (IG) with the ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



g.

Turn the power switch off.


h.

Disconnect the cable from the negative (-) auxiliary battery terminal.


i.

Reconnect the A59 inverter with converter assembly connector.


j.

Reconnect the D28 ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (ECM - HYBRID VEHICLE CONTROL ECU, INVERTER WITH CONVERTER ASSEMBLY)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D28 ECM connector.


c.

Disconnect the A21 hybrid vehicle control ECU connector.


d.

Disconnect the A59 inverter with converter assembly connector.


e.

Connect the cable to the negative (-) auxiliary battery terminal.


f.

Turn the power switch on (IG).


g.
U190603E02
0.833,1.354 1.292,0.531 false 1,3.927 0.635,4.26 false 0.167,0.156 0.427,0.385 0.26,0.229 10 false *a 0.167,2.24 0.427,2.469 0.26,0.229 10 false *b 0.146,1.323 0.417,1.49 0.271,0.167 10 false D28 1.344,3.875 1.615,4.042 0.271,0.167 10 false A21 1.344,0.438 1.74,0.604 0.396,0.167 10 false G2O 0.563,4.26 0.771,4.417 0.208,0.156 10 false GI

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D28-48 (G2O) or A21-10 (GI) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to ECM)
*b Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)

NOTICE:

Turning the power switch on (IG) with the inverter with converter assembly connector, hybrid vehicle control ECU connector and ECM connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



h.

Turn the power switch off.


i.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D28-48 (G2O) or A21-10 (GI)- Body ground Power switch off 10 kΩ or higher



j.

Disconnect the cable from the negative (-) auxiliary battery terminal.


k.

Reconnect the D28 ECM connector.


l.

Reconnect the A21 hybrid vehicle control ECU connector.


m.

Reconnect the A59 inverter with converter assembly connector.



OK

8.CHECK HYBRID VEHICLE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.CHECK HYBRID VEHICLE CONTROL ECU
a.

Disconnect all the connectors from the hybrid vehicle control ECU.


b.
U190511E02
0.917,1.896 0.646,2.344 true 1.833,1.833 2.073,2.396 true 0.698,1.167 0.969,1.333 0.271,0.167 10 false A21 1.969,1.167 2.24,1.333 0.271,0.167 10 false L5 0.177,0.229 0.365,0.417 0.188,0.188 10 false *a 0.563,2.354 0.75,2.542 0.188,0.188 10 false GI 2.042,2.406 2.229,2.594 0.188,0.188 10 false E1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-10 (GI) - L5-6 (E1) Always 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Hybrid Vehicle Control ECU)


c.

Reconnect the hybrid vehicle control ECU connectors.



OK

9.CHECK INVERTER WITH CONVERTER ASSEMBLY

NG

9.CHECK INVERTER WITH CONVERTER ASSEMBLY
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the A59 inverter with converter assembly connector.


c.
U154299E03
1.938,1.24 2.385,1.885 false 1.115,1.198 0.833,1.844 false 2.375,1.896 2.573,2.052 0.198,0.156 10 false GI 0.104,0.042 0.26,0.198 0.156,0.156 10 false *a 0.625,1.833 1.198,1.99 0.573,0.156 10 false GND1 0.219,1.031 0.49,1.198 0.271,0.167 10 false A59

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A59-29 (GI) - A59-28 (GND1) Power switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Inverter with Converter Assembly)


d.

Reconnect the A59 inverter with converter assembly connector.



OK

NG

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS