Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0A7A-203  Generator Inverter Performance  


DESCRIPTION

For a description of the inverter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0A78-266).

DTC No. INF Code DTC Detection Condition Trouble Area
P0A7A 203 Malfunction (short circuit) in the generator inverter inside the inverter with converter assembly
·

Inverter with converter assembly

·

Hybrid vehicle generator assembly

·

Generator cable



CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:
·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).

·

DTC P0A7A-203 is stored after any of DTCs P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810 and 811 are stored. After troubleshooting and repairing DTC P0A7A-203, be sure to troubleshoot all the other DTCs.

·

Depending on the conditions in which the vehicle is being operated when a short circuit occurs in the inverter with converter assembly, the hybrid vehicle transaxle assembly may be affected. As this DTC is stored if a short circuit occurs in the inverter with converter assembly, it is necessary to perform a road test to check the hybrid vehicle transaxle assembly. If problems are found, replace the malfunctioning parts.

·

After completing the repair, including the repair of previously output DTCs, drive the vehicle at a speed of approximately 40 km/h (25 mph) for 1 minute and check that DTC P0A92-261 (Hybrid Generator Performance) is not output. If DTC P0A92-261 (Hybrid Generator Performance) is output, replace the hybrid vehicle generator assembly.



HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1. Turn the power switch on (READY) and wait for 5 seconds or more.

2. Drive the vehicle for approximately 10 minutes mainly using the engine.


PROCEDURE

1.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)

OK

2.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

4.CHECK GENERATOR CABLE
2.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).



NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A-203.

Result
DTC No. Relevant Diagnosis
P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810, 811 Generator Inverter Performance

NOTICE:

DTC P0A7A-203 is stored after any of DTCs P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810 and 811 are stored. After troubleshooting and repairing DTC P0A7A-203, be sure to troubleshoot all the other DTCs.




NEXT

4.CHECK GENERATOR CABLE

OK

5.REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY

NG

8.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
5.REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY

NEXT

6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
6.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).



NEXT

7.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A-203.

Result
DTC No. Relevant Diagnosis
P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810, 811 Generator Inverter Performance

NOTICE:

DTC P0A7A-203 is stored after any of DTCs P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810 and 811 are stored. After troubleshooting and repairing DTC P0A7A-203, be sure to troubleshoot all the other DTCs.




NEXT

8.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY (MG1)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Remove the inverter with converter assembly.


c.

Disconnect the generator cable from the hybrid vehicle transaxle assembly.


d.
U190576E02
1.781,1.01 2.448,0.99 false 2.438,1.406 1.771,1.26 false 2.479,0.5 2.708,0.719 0.229,0.219 10 false W 2.479,0.906 2.729,1.156 0.25,0.25 10 false U 2.479,1.333 2.688,1.542 0.208,0.208 10 false V 0.125,0.073 0.375,0.302 0.25,0.229 10 true *a 2.896,0.906 3.167,1.073 0.271,0.167 10 false f2

Check MG1 for an interphase short using a milliohmmeter.

i.

Using a milliohmmeter, measure the resistance according to the value(s) in the table below.

HINT:

If the MG1 temperature is high, the resistance will vary greatly from the specification. Therefore, measure the resistance at least 8 hours after the vehicle is stopped.


Standard Resistance:
Tester Connection Condition Specified Condition
f2-2 (U) - f2-1 (V) Power switch off 87.0 to 96.2 mΩ
f2-1 (V) - f2-3 (W) Power switch off 87.0 to 96.2 mΩ
f2-3 (W) - f2-2 (U) Power switch off 87.0 to 96.2 mΩ


Text in Illustration
*a Hybrid Vehicle Transaxle Assembly

HINT:

To correct the variation of the measured resistance due to temperature, use the following formula to calculate the resistance at 20°C (68°F).

R20 = Rt / {1 + 0.00393 X (T - 20)}


The calculation is based on the following:

R20: Resistance at x 20°C (68°F) (mΩ)

Rt: Measured resistance (mΩ)

T: Temperature when the resistance is measured (°C)





e.

Using a megohmmeter set to 500 V, measure the resistance according to the value(s) in the table below.

NOTICE:

Be sure to set the megohmmeter to 500 V when performing this test. Using a setting higher than 500 V can result in damage to the component being inspected.


Standard Resistance:
Tester Connection Condition Specified Condition
f2-2 (U) - Body ground and shield ground Power switch off 100 MΩ or higher
f2-1 (V) - Body ground and shield ground Power switch off 100 MΩ or higher
f2-3 (W) - Body ground and shield ground Power switch off 100 MΩ or higher



f.

Connect the generator cable.


g.

Install the inverter with converter assembly.



OK

9.REPLACE GENERATOR CABLE

NG

12.REPLACE GENERATOR CABLE
9.REPLACE GENERATOR CABLE

NEXT

10.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
10.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).



NEXT

11.CHECK DTC OUTPUT (HYBRID CONTROL)
11.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A-203.

Result
DTC No. Relevant Diagnosis
P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810, 811 Generator Inverter Performance

NOTICE:

DTC P0A7A-203 is stored after any of DTCs P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810 and 811 are stored. After troubleshooting and repairing DTC P0A7A-203, be sure to troubleshoot all the other DTCs.




NEXT

12.REPLACE GENERATOR CABLE

NEXT

13.REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY
13.REPLACE HYBRID VEHICLE GENERATOR ASSEMBLY

NEXT

14.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
14.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).



NEXT

15.CHECK DTC OUTPUT (HYBRID CONTROL)
15.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Check the other DTCs that were output together with DTC P0A7A-203.

Result
DTC No. Relevant Diagnosis
P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810, 811 Generator Inverter Performance

NOTICE:

DTC P0A7A-203 is stored after any of DTCs P0A7A-122, 130, 322, 324, 325, 517, 518, 809, 810 and 811 are stored. After troubleshooting and repairing DTC P0A7A-203, be sure to troubleshoot all the other DTCs.




NEXT