Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2012.10
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0AFC-129  Hybrid Battery Pack Sensor Module  


DESCRIPTION

The battery smart unit (battery energy control module) sends HV battery voltage information to the power management control ECU via serial communication.

DTC No. INF Code DTC Detection Condition Trouble Area
P0AFC 129 HV battery voltage circuit malfunction Battery smart unit

CAUTION / NOTICE / HINT

NOTICE:

Performing the check procedures for a long time with the shift lever in N may cause DTC P3000-388 to be set.


HINT:
·

If, after performing troubleshooting, it is necessary to replace the battery smart unit, voltages need to be confirmed after installing the new battery smart unit. Confirm that "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" in the Data List are 208 V or more with the power switch on (READY), park (P) selected, and the engine stopped. When the system is normal, the "Power Resource VB", "VL-Voltage before Boosting", and "VH-Voltage after Boosting" values should be almost equal (voltage boosting will not occur when the shift lever is in neutral). If the difference between each voltage exceeds the values specified below, there is a malfunction in the inverter with converter assembly.

Inspection voltage Maximum voltage difference
Difference between "Power Resource VB" and "VL-Voltage before Boosting" 50 V
Difference between "Power Resource VB" and "VH-Voltage after Boosting" 70 V
Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" 90 V

·

After the repair, if "VL-Voltage before Boosting" and "Power Resource VB" are approximately the same when the power switch is turned on (READY) with park (P) selected and the accelerator pedal not depressed, the condition is judged as normal.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P0AFC-129 only is output, or DTCs other than the ones in the table below are also output. A
DTCs shown in Table 1 are output simultaneously. B
DTCs shown in Table 2 are output simultaneously. C


Table 1
DTC No. Relevant Diagnosis
P0A1A-151, 155, 156, 658, 659 Generator Control Module
P0A1B-164, 193, 512, 661, 786 Drive Motor "A" Control Module
P0A1D-148 Hybrid Powertrain Control Module
P0A78-266, 267 Drive Motor "A" Inverter Performance
P0A94-589, 590 DC/DC Converter Performance
P2511-149 HV CPU Power Relay Sensor Circuit Intermittent No Continuity
P3004-132 High Voltage Power Resource
P324E-788 MG-ECU Power Relay Intermittent Circuit
U0110 (all INF codes)*1 Lost Communication with Drive Motor Control Module "A"

Table 2
DTC No. Relevant Diagnosis
P0AFC-123 Hybrid Battery Pack Sensor Module
P0B3D-123 Hybrid Battery Voltage Sensor "A" Circuit Low
P0B42-123 Hybrid Battery Voltage Sensor "B" Circuit Low
P0B47-123 Hybrid Battery Voltage Sensor "C" Circuit Low
P0B4C-123 Hybrid Battery Voltage Sensor "D" Circuit Low
P0B51-123 Hybrid Battery Voltage Sensor "E" Circuit Low
P0B56-123 Hybrid Battery Voltage Sensor "F" Circuit Low
P0B5B-123 Hybrid Battery Voltage Sensor "G" Circuit Low
P0B60-123 Hybrid Battery Voltage Sensor "H" Circuit Low
P0B65-123 Hybrid Battery Voltage Sensor "I" Circuit Low
P308A-123 Hybrid Battery Voltage Sensor All Circuits Low

HINT:
·

*1: If any INF codes are output for this DTC, refer to the corresponding diagnostic procedure.

·

P0AFC-129 may be output due to a malfunction which causes the DTCs in the table above to be output. In this case, first troubleshoot the output DTCs in the table above. Then, perform a reproduction test to check that no DTCs are output.




e.

Turn the power switch off.



A

B

C