The inverter water pump assembly transmits rotation revolution information to the power management control ECU. The power management control ECU monitors the revolution and detects malfunctions.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P0C73 | 776 | A speed or intermittent stop malfunction occurs in the inverter water pump assembly.
A revolution malfunction (speed is too high/low) or an intermittent stop malfunction (operation stops intermittently when the revolution speed is abnormal) occurs in the inverter water pump assembly. |
·
Inverter cooling system ·
Wire harness or connector ·
Inverter water pump assembly ·
Power management control ECU |
The inverter water pump assembly operates when the power switch is on (READY).
| DTC No. | INF Code | Data List Item |
|---|---|---|
| P0C73 | 776 | ·
W/P Run Control Duty*1 ·
Inverter W/P Revolution ·
Ready Signal |
*1: This Data List item is related to the inverter water pump assembly.
| DTC No. | INF Code | Active Test |
|---|---|---|
| P0C73 | 776 | Activate the Water Pump*2 |
*2: This is an Active Test of the inverter water pump assembly.
In the case of a coolant leak, the inverter water pump assembly activates a fail-safe function. If the inverter water pump assembly is not the cause of the coolant leak, it is not necessary to replace it.
If this vehicle is jump started, etc. and excessive voltage is applied to the auxiliary battery, the inverter water pump assembly may suspend control as a self-protection function and store DTC. (When the auxiliary battery voltage returns to normal, the inverter water pump assembly will resume normal operation. In this case it is not necessary to replace the inverter water pump assembly.)
If air enters the system while bleeding air during coolant exchange, etc. and the inverter water pump assembly revolution speed becomes abnormally high, the inverter water pump assembly may suspend control as a fail-safe function and the hybrid vehicle control ECU may store this DTC. (When air bleeding is complete, the inverter water pump assembly will resume normal operation. In this case, it is not necessary to replace the inverter water pump assembly.)
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
Turn the power switch on (READY) and wait for 2 minutes or more.
A
B
C
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
When the inverter water pump assembly operation command line (SWP - IWP) is open or its connection is faulty, the inverter water pump assembly is operated forcibly.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Data List.
Select Inverter W/P Revolution in the Data List.
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter W/P Revolution | Power switch on (IG) | 625 rpm or less |
When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" displays a value lower than 625 rpm.
Turn the power switch off.
OK
NG
NEXT
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Active Test / Activate the Water Pump.
Select Inverter W/P Revolution in the Data List.
While performing the "Activate the Water Pump" Active Test, check Inverter W/P Revolution in the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter W/P Revolution | Power switch on (IG) | 2250 to 5625 rpm |
Perform the Active Test with the inverter coolant temperature between -15 and 65°C (5 to 149°F).
When the inverter water pump assembly is not operating, the Data List item "Inverter W/P Revolution" displays a value lower than 625 rpm.
Turn the power switch off.
OK
NG
A
B
OK
NG
Check the connector connections and contact pressure of the relevant terminals for the inverter water pump assembly connector (See page General>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>ELECTRONIC CIRCUIT INSPECTION PROCEDURE).
The connector is connected securely and there are no contact pressure problems.
OK
NG
Disconnect the A21 power management control ECU connector.
Disconnect the g1 inverter water pump assembly connector.
Measure the resistance according to the value(s) in the table below.
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
*b | Front view of wire harness connector
(to Inverter Water Pump Assembly) |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g1-3 (SWP) - A21-13 (IWP) | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| g1-3 (SWP) or A21-13 (IWP) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Check the condition (looseness, deterioration, etc.) of the wire to body ground for the inverter water pump assembly.
Reconnect the A21 power management control ECU connector.
Reconnect the g1 inverter water pump assembly connector.
OK
NG
Be sure to perform the inspection with the auxiliary battery voltage at 12 V or more.
When the auxiliary battery voltage is low, the inverter water pump assembly may not operate.
Connect the GTS to the DLC3.
Remove the IGCT No. 3 fuse from the engine room relay block and junction block assembly.
| *1 | Engine Room Relay Block and Junction Block Assembly |
| *2 | IGCT No. 3 Fuse |
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / ECU Data List / Inverter W/P Revolution.
Read the Data List.
| Tester Display | Condition | Specified Condition |
|---|---|---|
| Inverter W/P Revolution | Power switch on (IG) | 125 rpm or less |
Turn the power switch off.
Install the IGCT No. 3 fuse.
OK
NG
Disconnect the A21 power management control ECU connector.
Turn the power switch on (IG).
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A21-13 (IWP) - L5-6 (E1) | Power switch on (IG) | 11 to 14 V |
| *a | Rear view of wire harness connector
(to Power Management Control ECU) |
Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Reconnect the A21 power management control ECU connector.
OK
NG
Turn the power switch on (IG).
While turning the power switch on (IG), check the waveform between the power management control ECU terminals.
| Item | Content |
|---|---|
| Terminal | A21-13 (IWP) - L5-6 (E1) |
| Equipment Setting | 5 V/DIV., 50 ms./DIV. |
| Condition | Power switch on (IG) |
| *a | Component with Harness Connected
(Power Management Control ECU) |
Waveform duty ratio is between 3% and 9%.
Turn the power switch off.
OK
NG