If the inverter with converter assembly (MG ECU) is reset due to a problem with the power source in the inverter, the power management control ECU will set this DTC.
| DTC No. | INF Code | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| P324E | 788 | Error in reset signal from the inverter assembly power source IC | ·
Wire harness or connector ·
Inverter with converter assembly ·
Engine room junction block assembly ·
Power management control ECU ·
Hybrid battery junction block assembly ·
Service plug grip |
Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.
After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).
Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.
After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).
After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.
1. Turn the power switch on (IG) and wait for 5 seconds or more.
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| P324E-788 only is output. | A |
| U0110-159, 160, 656, 657 are also output. | B |
Turn the power switch off.
A
B
OK
NG
Be sure to wear insulated gloves.
Check that the service plug grip is not installed.
After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.
Disconnect the A59 inverter with converter assembly connector.
Remove the IGCT relay from the engine room relay block and junction block assembly.
Measure the resistance according to the value(s) in the table below.
| *1 | Engine Room Relay Block and Junction Block Assembly | *2 | IGCT Relay |
| *a | Front view of wire harness connector
(to Inverter with Converter Assembly) |
- | - |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A59-10 (+B) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
| A59-9 (+B2) - 5 (IGCT relay) | Power switch off | Below 1 Ω |
| A59-28 (GND1) - Body ground | Power switch off | Below 1 Ω |
| A59-27 (GND2) - Body ground | Power switch off | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A59-10 (+B) or A59-9 (+B2) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
Install the IGCT relay.
Reconnect the A59 inverter with converter assembly connector.
OK
NG
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output. | A |
| DTC P0A94-172, P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 is also output. | B |
| Other than above. | C |
Turn the power switch off.
A
B
C
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch off and wait for 30 seconds or more.
Turn the power switch on (IG) and wait for 5 seconds or more.
Turn the power switch on (READY).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs are output (not including history DTCs). | A |
| Only DTC P0A1A-151, P0A1A-659 or P324E-788 is output. | B |
| Other than above. | C |
Turn the power switch off.
C
A
B
Connect the GTS to the DLC3.
Turn the power switch on (IG).
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Read and record the DTCs and freeze frame data.
Clear DTCs and freeze frame data.
Turn the power switch off.
NEXT
Connect the GTS to the DLC3.
Turn the power switch on (IG) and wait for 5 seconds or more.
Turn the power switch on (READY) and wait for 5 seconds or more.
Depress the accelerator pedal with the engine stopped and park (P) selected to start the engine and idle it for 10 seconds or more.
Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.
Check if DTCs are output.
| Result | Proceed to |
|---|---|
| No DTCs are output. | A |
| DTCs other than P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 are output. | B |
| DTC P0A94-442, P0A94-553, P0A94-557, P3004-800 or P3004-801 is output. | C |
Turn the power switch off.
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
B
C
Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the part number of the inverter with converter assembly.
| Result | Proceed to | |
|---|---|---|
| Installation Position of Part No. Label | Part No. | |
| Front | - | A |
| Top | ·
G9200-47160 ·
G9200-47161 ·
G9200-47162 |
|
| Other than above. | B | |
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL COMPUTER>COMPONENTS)
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>MOTOR GENERATOR CONTROL COMPUTER>COMPONENTS)
Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the part number of the inverter with converter assembly.
| Result | Proceed to | |
|---|---|---|
| Installation Position of Part No. Label | Part No. | |
| Front | - | A |
| Top | ·
G9200-47160 ·
G9200-47161 ·
G9200-47162 |
|
| Other than above. | B | |
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
Check the installation position of the part No. label on the inverter with converter assembly (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).
Check the part number of the inverter with converter assembly.
| Result | Proceed to | |
|---|---|---|
| Installation Position of Part No. Label | Part No. | |
| Front | - | A |
| Top | ·
G9200-47160 ·
G9200-47161 ·
G9200-47162 |
|
| Other than above. | B | |
A
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)
B
(See pageEngine / Hybrid System>HYBRID / BATTERY CONTROL>POWER MODULE INTELLIGENT TRANSISTOR>COMPONENTS)