Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P082B-575  Gear Lever X Position Circuit Low  P082C-576  Gear Lever X Position Circuit High  P082E-571  Gear Lever Y Position Circuit Low  P082F-572  Gear Lever Y Position Circuit High  P181A-596  Gear Lever X Position Circuit "A" / "B" Correlation  P181B-595  Gear Lever Y Position Circuit "A" / "B" Correlation  P182B-577  Gear Lever X Position "B" Circuit Low  P182C-578  Gear Lever X Position "B" Circuit High  P182E-573  Gear Lever Y Position "B" Circuit Low  P182F-574  Gear Lever Y Position "B" Circuit High  


DESCRIPTION

HINT:
·

The electronic shift lever system is a linkless type that does not use a shift cable.

·

The shift and select sensors are non-contact type sensors.



The shift lever (shift lock control unit assembly) is a momentary type, which returns to its home position by spring reaction as the driver's hand is released from the shift lever after shifting.

The shift lever (shift lock control unit assembly) contains a shift sensor and a select sensor to detect the shift lever position (Home, R, N, D or B). Because the shift sensor operates using Hall ICs and the select sensor operates using MR ICs, they can accurately detect the shift lever position in a reliable manner. Both sensors contain two detection circuits, a main and a sub circuit.

A280634E02
5.281,4.844 6.25,5.115 false 4.656,2.771 5.125,3.448 5.125,3.448 5.833,2.76 false 4.583,2.802 4.219,2.75 4.219,2.75 4.573,2.885 false 5.458,0.844 6.344,0.427 false 5.167,0.844 4.479,0.604 false 1.083,2.75 0.896,3 false 2.01,1.708 2.594,1.229 false 4.667,6.667 5.135,7.354 5.135,7.354 5.844,6.667 false 4.583,6.708 4.219,6.667 4.219,6.667 4.573,6.792 false 5.458,4.75 6.344,4.333 false 5.167,4.75 4.479,4.51 false 2.844,6.635 3.042,6.875 false 1.906,5.615 1.313,5.125 false 5.281,0.938 6.25,1.219 false 0.219,0.573 2.313,0.75 2.094,0.177 10 false Shift Lock Control Unit Assembly 0.219,4.5 2.313,4.677 2.094,0.177 10 false Shift Lock Control Unit Assembly 0.146,0.094 0.833,0.271 0.688,0.177 12 false for LHD: 0.146,4.021 0.833,4.198 0.688,0.177 12 false for RHD: 4.927,0.167 5.771,0.354 0.844,0.188 10 false Shift Sensor 2.635,1.125 3.625,1.313 0.99,0.188 10 false Select Sensor 0.448,3 1.292,3.188 0.844,0.188 10 false Shift Sensor 4.031,0.469 4.5,0.656 0.469,0.188 10 false Hall IC 3.781,2.646 4.25,2.833 0.469,0.188 10 false MR IC 4.875,1.531 5.865,1.719 0.99,0.188 10 false Select Sensor 6.396,0.323 6.74,0.51 0.344,0.188 10 false Yoke 6.292,1.167 6.854,1.354 0.563,0.188 10 false Magnet 6.292,5.063 6.854,5.25 0.563,0.188 10 false Magnet 4.771,3.469 5.76,3.656 0.99,0.188 10 false Magnet Slider 4.927,4.083 5.771,4.271 0.844,0.188 10 false Shift Sensor 0.385,5.01 1.375,5.198 0.99,0.188 10 false Select Sensor 2.719,6.906 3.563,7.094 0.844,0.188 10 false Shift Sensor 4,4.385 4.469,4.573 0.469,0.188 10 false Hall IC 3.781,6.563 4.25,6.75 0.469,0.188 10 false MR IC 4.875,5.458 5.865,5.646 0.99,0.188 10 false Select Sensor 6.396,4.24 6.74,4.427 0.344,0.188 10 false Yoke 4.771,7.375 5.771,7.583 1,0.208 10 false Magnet Slider

The shift sensor outputs voltage, which varies between 0 and 5 V in accordance with the vertical movement of the shift lever, to the power management control ECU. The power management control ECU interprets low level voltage input from the shift sensor as the R position, middle level voltage as the home or N position, and high level voltage as the D or B position.

A221567E08
2.396,4.115 3.74,4.479 1.344,0.365 10 false Power Management Control ECU 0.646,4.354 1.49,4.542 0.844,0.188 10 false Shift Sensor 1.052,0.979 1.521,1.167 0.469,0.188 10 false Hall IC 3.885,1.188 5.104,1.667 1.219,0.479 10 false Shift Sensor Output Voltage (V) 0.573,0.573 1.135,0.76 0.563,0.188 10 false Magnet 0.573,3.906 1.135,4.094 0.563,0.188 10 false Magnet 1.052,3.5 1.521,3.688 0.469,0.188 10 false Hall IC 2.042,1.031 2.51,1.219 0.469,0.188 10 false VCX1 2.042,1.51 2.51,1.698 0.469,0.188 10 false VSX1 2.042,1.99 2.51,2.177 0.469,0.188 10 false E2X1 2.042,2.458 2.51,2.646 0.469,0.188 10 false VCX2 2.042,2.938 2.51,3.125 0.469,0.188 10 false VSX2 2.042,3.406 2.51,3.594 0.469,0.188 10 false E2X2 2.896,2.323 3.188,2.51 0.292,0.188 10 false 5 V 2.896,0.896 3.188,1.083 0.292,0.188 10 false 5 V 4.208,2.083 4.833,2.271 0.625,0.188 10 false 4.2 to 4.8 4.583,2.417 4.875,2.604 0.292,0.188 10 false 2.5 4.208,2.76 4.833,2.948 0.625,0.188 10 false 0.2 to 0.8 6.698,2.167 7.021,2.354 0.323,0.188 10 false High 6.698,2.417 7.146,2.604 0.448,0.188 10 false Middle 6.698,2.667 7.031,2.854 0.333,0.188 10 false Low 6.229,3.188 6.885,3.552 0.656,0.365 10 false Operation Range 4.583,3.792 6.833,4 2.25,0.208 10 false Shift Sensor Rotational Angle (deg) 5.281,3.563 5.698,3.75 0.417,0.188 10 false 7°24' 5.865,3.563 6.281,3.75 0.417,0.188 10 false 7°24' 5.698,3.563 5.823,3.75 0.125,0.188 10 false 0 0.771,5.656 1.052,5.844 0.281,0.188 10 false 0 V 0.771,7.146 1.031,7.333 0.26,0.188 10 false 5 V 6.177,5.656 6.458,5.844 0.281,0.188 10 false 0 V 6.177,7.146 6.438,7.333 0.26,0.188 10 false 5 V 0.094,6.135 1.052,6.49 0.958,0.354 10 false Shift Sensor Output Voltage 6.167,6.135 7.125,6.49 0.958,0.354 10 false Shift Sensor Output Voltage 2.531,5.625 3.458,5.823 0.927,0.198 10 false Home Position 3.698,5.625 4.625,5.823 0.927,0.198 10 false Home Position 0.208,5.125 0.771,5.313 0.563,0.188 10 false for LHD: 3.646,5.125 4.208,5.313 0.563,0.188 10 false for RHD:

The select sensor outputs voltage, which varies between 0 and 5 V in accordance with the horizontal movement of the shift lever, to the power management control ECU. The power management control ECU interprets low level voltage input from the select sensor as the home or B position, and high level voltage as the R, N, or D position.

The power management control ECU determines the position of the shift lever in accordance with the combination of the signals from the shift sensor and select sensor.

A221568E02
2.564,4.046 3.912,4.410 1.348,0.364 10 Power Management Control ECU 0.799,4.018 1.740,4.206 0.941,0.188 10 Select Sensor 1.903,1.496 2.374,1.684 0.471,0.188 10 MR IC 2.954,1.561 4.159,1.750 1.205,0.188 10 Output Voltage (V) 1.455,1.066 2.433,1.254 0.978,0.188 10 Magnet Slider 2.09,2.124 2.563,2.313 0.473,0.188 10 VCX3 2.09,2.363 2.563,2.551 0.473,0.188 10 VSX3 2.09,2.956 2.563,3.144 0.473,0.188 10 VCX4 2.09,3.194 2.563,3.382 0.473,0.188 10 VSX4 3.482,2.864 3.682,3.053 0.200,0.188 10 +B 3.155,2.033 3.383,2.221 0.228,0.188 10 +B 4.171,1.47 4.417,1.659 0.246,0.188 10 4.3 4.171,1.751 4.463,1.939 0.292,0.188 10 2.9 4.171,1.972 4.398,2.160 0.228,0.188 10 1.6 6.718,1.61 7.038,1.799 0.320,0.188 10 High 6.718,2.065 7.052,2.254 0.334,0.188 10 Low 5.218,2.708 6.302,2.896 1.084,0.188 10 Operation Range 4.666,2.841 5.190,3.191 0.524,0.350 10 Home Position 0.283,3.042 0.640,3.230 0.357,0.188 10 Slide 4.171,2.182 4.398,2.370 0.228,0.188 10 1.0 3.912,2.694 4.635,2.882 0.723,0.188 10 Home or B 3.991,0.854 4.931,1.042 0.940,0.188 10 Undetermined 6.223,0.863 6.882,1.051 0.658,0.188 10 R, N or D 5.33,3.017 6.415,3.205 1.084,0.188 10 Sliding Amount 4.379,5.463 5.315,5.651 0.936,0.188 10 Home Position 1.934,5.463 2.870,5.651 0.936,0.188 10 Home Position 0.43,4.956 1.009,5.145 0.580,0.188 10 for LHD: 4.108,4.956 4.687,5.145 0.580,0.188 10 for RHD: 2.221,3.518 2.692,3.706 0.471,0.188 10 MR IC


DTC No. INF Code DTC Detection Condition Trouble Area
P082B 575 Open or GND short in select main sensor circuit
·

Wire harness or connector

·

Shift lock control unit assembly

·

Power management control ECU


P082C 576 +B short in select main sensor circuit
P082E 571 Open or GND short in shift main sensor circuit
P082F 572 +B short in shift main sensor circuit
P181A 596 Difference between select main sensor value and select sub sensor value is large
P181B 595 Difference between shift main sensor value and shift sub sensor value is large
P182B 577 Open or GND short in select sub sensor circuit
P182C 578 +B short in select sub sensor circuit
P182E 573 Open or GND short in shift sub sensor circuit
P182F 574 +B short in shift sub sensor circuit

HINT:

When any of DTCs P082E-571, P082F-572, P182E-573 or P182F-574 are output, check Shift Sensor Main and Shift Sensor Sub voltages using the GTS.


Shift Sensor Main, Shift Sensor Sub
R position
(Main)
Home or N position
(Main)
D or B position
(Main)
R position
(Sub)
Home or N position
(Sub)
D or B position
(Sub)
Trouble Area
0.3 to 1.8 V 2.0 to 3.0 V 3.2 to 4.8 V 0.3 to 1.8 V 2.0 to 3.0 V 3.2 to 4.8 V Correct shift sensor voltage
0 to 0.3 V 0 to 0.3 V 0 to 0.3 V 0.3 to 1.8 V 2.0 to 3.0 V 3.2 to 4.8 V Open in VCX1 circuit
GND short in VSX1 circuit
0.3 to 1.8 V 2.0 to 3.0 V 3.2 to 4.8 V 0 to 0.3 V 0 to 0.3 V 0 to 0.3 V Open in VCX2 circuit
GND short in VSX2 circuit
4.8 to 5.0 V 4.8 to 5.0 V 4.8 to 5.0 V 0.3 to 1.8 V 2.0 to 3.0 V 3.2 to 4.8 V Open in VSX1 circuit
Open in E2X1 circuit
0.3 to 1.8 V 2.0 to 3.0 V 3.2 to 4.8 V 4.8 to 5.0 V 4.8 to 5.0 V 4.8 to 5.0 V Open in VSX2 circuit
Open in E2X2 circuit

HINT:

When any of DTCs P082B-575, P082C-576, P182B-577 or P182C-578 are output, check Shift Sensor Select Main and Shift Sensor Select Sub voltages using the GTS.


Shift Sensor Select Main, Shift Sensor Select Sub
R, N or D Position
Select Main)
Home or B Position
Select Main)
R, N or D Position
Select Sub)
Home or B Position
Select Sub)
Trouble Area
2.9 to 4.3 V 1.0 to 1.6 V 2.9 to 4.3 V 1.0 to 1.6 V Correct select sensor voltage
0 to 0.5 V 0 to 0.5 V 2.9 to 4.3 V 1.0 to 1.6 V Open in VCX3 circuit
Open or GND short in VSX3 circuit
2.9 to 4.3 V 1.0 to 1.6 V 0 to 0.5 V 0 to 0.5 V Open in VCX4 circuit
Open or GND short in VSX4 circuit
4.9 to 5.0 V 4.9 to 5.0 V 2.9 to 4.3 V 1.0 to 1.6 V +B short in VSX3 circuit
2.9 to 4.3 V 1.0 to 1.6 V 4.9 to 5.0 V 4.9 to 5.0 V +B short in VSX4 circuit

WIRING DIAGRAM

A259940E01
5.264,5.94 6.612,6.304 1.348,0.364 10 Power Management Control ECU 1.243,2.951 2.082,3.139 0.839,0.188 10 Shift Sensor 0.385,1.433 0.856,1.621 0.471,0.188 10 Hall IC 0.446,4.38 0.916,4.568 0.471,0.188 10 MR IC 2.04,0.355 2.513,0.543 0.473,0.188 10 VCX1 2.04,0.747 2.513,0.935 0.473,0.188 10 VSX1 2.04,1.139 2.513,1.327 0.473,0.188 10 E2X1 2.04,1.541 2.513,1.729 0.473,0.188 10 VCX2 2.04,1.933 2.513,2.121 0.473,0.188 10 VSX2 2.04,2.325 2.513,2.514 0.473,0.188 10 E2X2 5.92,1.466 6.212,1.654 0.292,0.188 10 5 V 5.92,0.256 6.212,0.445 0.292,0.188 10 5 V 5.945,3.444 6.223,3.632 0.279,0.188 10 +B 6.346,4.474 6.611,4.662 0.265,0.188 10 +B 1.243,5.622 2.203,5.835 0.959,0.213 10 Select Sensor 1.243,2.778 1.652,2.967 0.408,0.188 10 L127 1.243,5.454 1.598,5.643 0.355,0.188 10 L126 5.296,0.346 5.769,0.535 0.473,0.188 10 VCX1 5.296,0.739 5.769,0.927 0.473,0.188 10 VSX1 5.296,1.131 5.769,1.319 0.473,0.188 10 E2X1 5.296,1.547 5.769,1.735 0.473,0.188 10 VCX2 5.296,1.939 5.769,2.127 0.473,0.188 10 VSX2 5.296,2.331 5.769,2.519 0.473,0.188 10 E2X2 2.482,0.34 2.650,0.529 0.167,0.188 10 3 2.482,0.719 2.650,0.907 0.167,0.188 10 1 2.482,1.139 2.650,1.327 0.167,0.188 10 2 2.482,1.517 2.650,1.706 0.167,0.188 10 6 2.482,1.938 2.650,2.126 0.167,0.188 10 4 2.482,2.33 2.650,2.518 0.167,0.188 10 5 5.032,0.324 5.240,0.513 0.207,0.188 10 26 5.032,0.703 5.240,0.891 0.207,0.188 10 25 5.032,1.123 5.240,1.311 0.207,0.188 10 24 5.032,1.501 5.240,1.689 0.207,0.188 10 21 5.032,1.921 5.240,2.110 0.207,0.188 10 22 5.032,2.314 5.240,2.502 0.207,0.188 10 23 2.04,3.597 2.513,3.785 0.473,0.188 10 VCX3 2.04,4.003 2.513,4.191 0.473,0.188 10 VSX3 2.04,4.601 2.513,4.789 0.473,0.188 10 VCX4 2.04,5.007 2.513,5.195 0.473,0.188 10 VSX4 5.296,3.597 5.769,3.785 0.473,0.188 10 VCX3 5.296,4.003 5.769,4.191 0.473,0.188 10 VSX3 5.296,4.601 5.769,4.789 0.473,0.188 10 VCX4 5.296,5.007 5.769,5.195 0.473,0.188 10 VSX4 2.482,3.591 2.650,3.779 0.167,0.188 10 5 2.482,3.997 2.650,4.185 0.167,0.188 10 4 2.482,4.6 2.650,4.788 0.167,0.188 10 2 2.482,4.992 2.650,5.180 0.167,0.188 10 1 5.046,3.603 5.254,3.791 0.207,0.188 10 19 5.046,3.995 5.254,4.183 0.207,0.188 10 20 5.046,4.597 5.254,4.786 0.207,0.188 10 17 5.046,4.99 5.254,5.178 0.207,0.188 10 18 5.264,5.79 5.619,5.979 0.355,0.188 10 L5

Refer to the wiring diagram for DTC P0AE6-225 (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0AE6-225).

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG).

2.

Slowly move the shift lever as follows: N → R → N → D → B



PROCEDURE

1.READ VALUE USING GTS (SHIFT SENSOR MAIN, SHIFT SENSOR SUB)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor Main, Shift Sensor Sub.


d.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Shift Sensor Main R position 0.3 to 1.8 V
Home or N position 2.0 to 3.0 V
D or B position 3.2 to 4.8 V
Shift Sensor Sub R position 0.3 to 1.8 V
Home or N position 2.0 to 3.0 V
D or B position 3.2 to 4.8 V



e.

Turn the power switch off.



OK

2.READ VALUE USING GTS (SHIFT SENSOR SELECT MAIN, SHIFT SENSOR SELECT SUB)

NG

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SHIFT SENSOR)
2.READ VALUE USING GTS (SHIFT SENSOR SELECT MAIN, SHIFT SENSOR SELECT SUB)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List / Shift Sensor Select Main, Shift Sensor Select Sub.


d.

Read the Data List.

Result:
Tester Display Condition Specified Condition
Shift Sensor Select Main R, N or D Position 2.9 to 4.3 V
Home or B Position 1.0 to 1.6 V
Shift Sensor Select Sub R, N or D Position 2.9 to 4.3 V
Home or B Position 1.0 to 1.6 V



e.

Turn the power switch off.



OK

3.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SELECT SENSOR)
3.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NEXT

4.CLEAR DTC
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

5.CHECK DTC OUTPUT (HYBRID CONTROL)
5.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → B.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573 or P182F-574 is output again. B



f.

Turn the power switch off.



A

COMPLETED

B

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SHIFT SENSOR)
a.

Disconnect the L5 power management control ECU connector.


b.

Disconnect the L127 shift sensor connector.


c.
A379061E01
2,2.583 2.417,2.833 0.417,0.25 1.5,4.333 1.917,4.583 0.417,0.25 1.417,2.5 1.875,2.115 false 1.417,2.021 1.917,2.104 false 1.417,1.667 1.958,2.115 false 2.583,1.667 2.01,2.104 false 2.583,2.031 2.063,2.104 false 2.583,2.521 2.104,2.125 false 0.75,3.5 1.292,3.698 false 0.833,4.083 1.448,3.729 false 1.333,4.167 1.625,3.729 false 2.083,4.167 1.792,3.75 false 2.5,4.083 1.927,3.74 false 2.583,3.5 2.073,3.719 false 0.083,0.083 0.542,0.354 0.458,0.271 10 false *a 0.094,2.844 0.552,3.115 0.458,0.271 10 false *b 0.979,1.573 1.438,1.844 0.458,0.271 10 false E2X1 1.01,1.958 1.469,2.229 0.458,0.271 10 false VSX1 1.021,2.427 1.479,2.698 0.458,0.271 10 false VCX1 2.115,2.625 2.573,2.896 0.458,0.271 10 false L5 1.552,4.375 2.01,4.646 0.458,0.271 10 false L127 2.656,2.458 3.115,2.729 0.458,0.271 10 false VCX2 2.677,1.979 3.135,2.25 0.458,0.271 10 false VSX2 2.656,1.604 3.115,1.875 0.458,0.271 10 false E2X2 2.635,3.417 3.094,3.688 0.458,0.271 10 false VCX2 2.563,4.031 3.021,4.302 0.458,0.271 10 false E2X2 2.042,4.177 2.5,4.448 0.458,0.271 10 false VSX2 1.063,4.198 1.521,4.469 0.458,0.271 10 false VCX1 0.365,3.385 0.823,3.656 0.458,0.271 10 false VSX1 0.458,4.021 0.917,4.292 0.458,0.271 10 false E2X1

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L5-26 (VCX1) - L127-3 (VCX1) Power switch off Below 1 Ω
L5-25 (VSX1) - L127-1 (VSX1) Power switch off Below 1 Ω
L5-24 (E2X1) - L127-2 (E2X1) Power switch off Below 1 Ω
L5-21 (VCX2) - L127-6 (VCX2) Power switch off Below 1 Ω
L5-22 (VSX2) - L127-4 (VSX2) Power switch off Below 1 Ω
L5-23 (E2X2) - L127-5 (E2X2) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L5-26 (VCX1) or L127-3 (VCX1) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-25 (VSX1) or L127-1 (VSX1) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-24 (E2X1) or L127-2 (E2X1) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-21 (VCX2) or L127-6 (VCX2) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-22 (VSX2) or L127-4 (VSX2) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-23 (E2X2) or L127-5 (E2X2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Shift Sensor)

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Reconnect the L127 shift sensor connector.


e.

Reconnect the L5 power management control ECU connector.



OK

7.CHECK POWER MANAGEMENT CONTROL ECU (VCX1, VCX2 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK POWER MANAGEMENT CONTROL ECU (VCX1, VCX2 VOLTAGE)
a.

Disconnect the L127 shift sensor connector.


b.

Turn the power switch on (IG).


c.
U154313E02
1.479,1.177 1.063,1.448 false 1.646,1.177 1.49,1.583 false 1.958,1.177 2.094,1.594 false 2.125,1.167 2.615,1.521 false 0.104,0.146 0.365,0.333 0.26,0.188 10 false *a 2.604,1.542 3.01,1.813 0.406,0.271 10 false VCX2 1.26,1.625 1.667,1.792 0.406,0.167 10 false VCX1 1.927,1.615 2.375,1.813 0.448,0.198 10 false E2X2 0.698,1.448 1.073,1.646 0.375,0.198 10 false E2X1 0.365,0.979 0.708,1.146 0.344,0.167 10 false L127

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L127-3 (VCX1) - L127-2 (E2X1) Power switch on (IG) 4.5 to 5.5 V
L127-6 (VCX2) - L127-5 (E2X2) Power switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Sensor)

NOTICE:

Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the L127 shift sensor connector.



OK

8.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

8.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NEXT

9.CLEAR DTC
9.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

10.CHECK DTC OUTPUT (HYBRID CONTROL)
10.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → B.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573 or P182F-574 is output again. B



f.

Turn the power switch off.



A

COMPLETED

B

11.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - SELECT SENSOR)
a.

Disconnect the L5 power management control ECU connector.


b.

Disconnect the L126 select sensor connector.


c.
A379060E01
0.583,3.333 1,3.583 0.417,0.25 1.083,1.75 1.5,2 0.417,0.25 2.448,1.885 2.167,2.031 false 2.458,1.646 2.125,2.021 false 2.51,2.417 2.219,2.031 false 2.5,2.167 2.26,2.031 false 1.083,4 1.396,3.573 false 1.5,4 1.552,3.573 false 1.917,4 1.802,3.573 false 2.333,4 1.917,3.573 false 0.073,0.063 0.51,0.354 0.438,0.292 10 false *a 0.125,2.823 0.563,3.115 0.438,0.292 10 false *b 1.198,1.792 1.635,2.083 0.438,0.292 10 false L5 0.635,3.375 1.073,3.667 0.438,0.292 10 false L126 2.51,1.563 2.948,1.854 0.438,0.292 10 false VSX3 2.427,2.427 2.865,2.719 0.438,0.292 10 false VSX4 2.552,2.125 2.99,2.417 0.438,0.292 10 false VCX4 2.5,1.813 2.938,2.104 0.438,0.292 10 false VCX3 0.865,4.031 1.302,4.323 0.438,0.292 10 false VSX4 1.354,4.042 1.792,4.333 0.438,0.292 10 false VCX4 1.813,4.031 2.25,4.323 0.438,0.292 10 false VSX3 2.271,4.021 2.708,4.313 0.438,0.292 10 false VCX3

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L5-19 (VCX3) - L126-5 (VCX3) Power switch off Below 1 Ω
L5-20 (VSX3) - L126-4 (VSX3) Power switch off Below 1 Ω
L5-17 (VCX4) - L126-2 (VCX4) Power switch off Below 1 Ω
L5-18 (VSX4) - L126-1 (VSX4) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L5-19 (VCX3) or L126-5 (VCX3) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-20 (VSX3) or L126-4 (VSX3) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-17 (VCX4) or L126-2 (VCX4) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-18 (VSX4) or L126-1 (VSX4) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector:
(to Power Management Control ECU)
*b Front view of wire harness connector:
(to Select Sensor)

HINT:

As necessary, check that there is no short to power supply wires when performing the above wire harness inspection.



d.

Reconnect the L126 select sensor connector.


e.

Reconnect the L5 power management control ECU connector.



OK

12.CHECK POWER MANAGEMENT CONTROL ECU (VCX3, VCX4 VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

12.CHECK POWER MANAGEMENT CONTROL ECU (VCX3, VCX4 VOLTAGE)
a.

Disconnect the L126 select sensor connector.


b.

Turn the power switch on (IG).


c.
U154312E02
1.563,1.229 1.438,1.573 false 1.979,1.229 2.083,1.552 false 0.125,0.156 0.427,0.344 0.302,0.188 10 false *a 1.198,1.573 1.594,1.781 0.396,0.208 10 false VCX4 1.917,1.573 2.313,1.781 0.396,0.208 10 false VCX3 0.667,0.979 1,1.146 0.333,0.167 10 false L126

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L126-5 (VCX3) - Body ground Power switch on (IG) 9 to 14 V
L126-2 (VCX4) - Body ground Power switch on (IG) 9 to 14 V


Text in Illustration
*a Front view of wire harness connector:
(to Select Sensor)

NOTICE:

Turning the power switch on (IG) with the connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Reconnect the L126 select sensor connector.



OK

13.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

13.REPLACE SHIFT LOCK CONTROL UNIT ASSEMBLY

NEXT

14.CLEAR DTC
14.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

15.CHECK DTC OUTPUT (HYBRID CONTROL)
15.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

With the brake pedal depressed, slowly move the shift lever as follows to select each shift state: N → R → N → D → B.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
P082B-575, P082C-576, P082E-571, P082F-572, P181A-596, P181B-595, P182B-577, P182C-578, P182E-573 or P182F-574 is output again. B



f.

Turn the power switch off.



A

COMPLETED

B