Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P085D-582  Gear Shift Control Module "A" Performance  P085D-599  Gear Shift Control Module "A" Performance  P0861-597  Gear Shift Control Module "A" Communication Circuit Low  P0862-598  Gear Shift Control Module "A" Communication Circuit High  


DESCRIPTION

When a signal is input from the P position switch (transmission shift main switch) or shift lever, the power management control ECU transmits a P position control (PCON) signal to the transmission control ECU assembly. Based on this signal, the transmission control ECU assembly actuates the shift control actuator assembly in order to mechanically lock or unlock the counter drive gear in the hybrid vehicle transaxle assembly.

P position state (engaged or released) of the actuator assembly is sent to the power management control ECU as a P position (PPOS) signal.

A256078E04
6.083,1.385 5.469,0.167 5.469,0.167 5.281,0.167 false 1.573,2.01 2.917,2.375 1.344,0.365 10 false Power Management Control ECU 0.26,2.219 1.01,2.406 0.75,0.188 10 false Shift Lever 0.083,1.156 1.219,1.344 1.135,0.188 10 false P Position Switch 2.667,1.219 3.531,1.406 0.865,0.188 10 false PCON signal 2.74,1.688 3.604,1.875 0.865,0.188 10 false PPOS signal 3.427,2.01 4.771,2.375 1.344,0.365 10 false Transmission Control ECU Assembly 5.865,1.917 7.156,2.281 1.292,0.365 10 false Hybrid Vehicle Transaxle Assembly 3.896,0.083 5.25,0.448 1.354,0.365 10 false Shift Control Actuator Assembly 4.427,1.219 5.677,1.542 1.25,0.323 10 false Actuator Energized 4.49,1.698 5.854,2.042 1.365,0.344 10 false Motor Position signal

DTC No. INF Code DTC Detection Condition Trouble Area
P085D 582 P position (PPOS) signal is logically inconsistent
·

Wire harness or connector

·

Transmission control ECU assembly

·

Power management control ECU


599 P position (PPOS) signal malfunction (output pulse is abnormal)
P0861 597 GND short in P position (PPOS) signal circuit
P0862 598 +B short in P position (PPOS) signal circuit

WIRING DIAGRAM

C244639E05
1.25,2.573 1.552,2.74 0.302,0.167 10 false A22 1.25,2.74 3.385,2.927 2.135,0.188 10 false Power Management Control ECU 4.771,2.573 5.052,2.729 0.281,0.156 10 false A24 4.771,2.74 6.51,3.115 1.74,0.375 10 false Transmission Control ECU Assembly 2.073,1.073 2.531,1.24 0.458,0.167 10 false PCON 2.083,1.885 2.51,2.052 0.427,0.167 10 false PPOS 4.823,1.094 5.281,1.26 0.458,0.167 10 false PCON 4.823,1.896 5.25,2.063 0.427,0.167 10 false PPOS 2.563,0.948 2.781,1.125 0.219,0.177 10 false 22 4.573,0.948 4.792,1.125 0.219,0.177 10 false 22 2.563,1.74 2.76,1.906 0.198,0.167 10 false 28 4.573,1.75 4.792,1.906 0.219,0.156 10 false 23

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 10 seconds or more.

2.

Depress the brake pedal, move the shift lever to N, and wait for 10 seconds or more.

3.

Push the transmission shift main switch (P position switch) and wait for 10 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (TRANSMISSION CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Chassis / Transmission Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Electronic shift lever system DTCs are not output. A
Any of the following DTCs are output. B


DTC No. Relevant Diagnosis
C2309 Open in B+ Circuit
C2311 Communication Error from HV ECU


e.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - TRANSMISSION CONTROL ECU ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the A22 power management control ECU connector.


b.

Disconnect the A24 transmission control ECU assembly connector.


c.

Turn the power switch on (IG).


d.
A379063E01
0.417,3.667 0.833,3.917 0.417,0.25 0.417,1.75 0.833,2 0.417,0.25 1.573,1.99 1.938,1.781 false 1.677,2.063 1.958,2.156 false 1.615,4.396 1.781,4.01 false 2.104,4.396 1.896,4.01 false 0.104,0.115 0.708,0.427 0.604,0.313 10 false *a 0.49,1.792 1.094,2.104 0.604,0.313 10 false A22 0.094,2.885 0.698,3.198 0.604,0.313 10 false *b 0.49,3.708 1.094,4.021 0.604,0.313 10 false A24 1.979,1.667 2.583,1.979 0.604,0.313 10 false PCON 2.01,2.083 2.615,2.396 0.604,0.313 10 false PPOS 1.99,4.417 2.604,4.667 0.615,0.25 10 false PPOS 1.396,4.406 2,4.667 0.604,0.26 10 false PCON

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A24-22 (PCON) - Body ground Power switch on (IG) Below 1 V
A24-23 (PPOS) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Transmission Control ECU Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A22-22 (PCON) - A24-22 (PCON) Power switch off Below 1 Ω
A22-28 (PPOS) - A24-23 (PPOS) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A22-22 (PCON) or A24-22 (PCON) - Body ground and other terminals Power switch off 10 kΩ or higher
A22-28 (PPOS) or A24-23 (PPOS) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the A24 transmission control ECU assembly connector.


h.

Reconnect the A22 power management control ECU connector.



OK

3.CHECK POWER MANAGEMENT CONTROL ECU (PCON SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK POWER MANAGEMENT CONTROL ECU (PCON SIGNAL)
a.

Turn the power switch on (IG).


b.
A379077E01
1.25,1.75 1.667,2 0.417,0.25 1.875,1.75 2.25,2 0.375,0.25 1.844,1.063 2.115,0.531 false 1.594,1.208 1.219,0.49 false 0.115,0.083 0.656,0.354 0.542,0.271 10 false *a 1.031,0.313 1.573,0.583 0.542,0.271 10 false PCON 2.073,0.333 2.615,0.604 0.542,0.271 10 false E1 1.323,1.792 1.865,2.063 0.542,0.271 10 false A22 1.979,1.792 2.521,2.063 0.542,0.271 10 false L5 2.844,3.406 3.385,3.677 0.542,0.271 10 false GND

Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal A22-22 (PCON) - L5-6 (E1)
Equipment Setting 10V/DIV., 10ms/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
P position control (PCON) signal waveform appears. A
P position control (PCON) signal waveform does not appear. B


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



A

4.CHECK POWER MANAGEMENT CONTROL ECU (PPOS SIGNAL)

B

4.CHECK POWER MANAGEMENT CONTROL ECU (PPOS SIGNAL)
a.

Turn the power switch on (IG).


b.
A379078E01
1.333,1.75 1.75,2 0.417,0.25 1.958,1.75 2.333,2 0.375,0.25 1.833,1.104 2.094,0.563 false 1.677,1.302 1.271,0.573 false 2.844,3.51 3.271,3.719 0.427,0.208 10 false GND 0.125,0.104 0.552,0.313 0.427,0.208 10 false *a 1.01,0.375 1.5,0.583 0.49,0.208 10 false PPOS 2.031,0.365 2.458,0.573 0.427,0.208 10 false E1 1.406,1.792 1.833,2 0.427,0.208 10 false A22 2.063,1.792 2.49,2 0.427,0.208 10 false L5

Connect an oscilloscope between the power management control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal A22-28 (PPOS) - L5-6 (E1)
Equipment Setting 10V/DIV., 10ms/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
P position (PPOS) signal waveform appears A
P position (PPOS) signal waveform does not appear B


Text in Illustration
*a Component with harness connected
(Power Management Control ECU)


c.

Turn the power switch off.



A

5.REPLACE POWER MANAGEMENT CONTROL ECU

B

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

5.REPLACE POWER MANAGEMENT CONTROL ECU

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

7.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and leave the vehicle as it is for 10 seconds.


c.

Depress the brake pedal, move the shift lever to N and leave the vehicle as it is for 10 seconds.


d.

Push the P position switch (transmission shift main switch) and leave the vehicle as it is for 10 seconds.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
P085D-582, P085D-599, P0861-597 or P0862-598 is output again. B



g.

Turn the power switch off.



A

COMPLETED

B

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY