Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2016.05–2017.12
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P085D-582  Gear Shift Control Module "A" Performance  P085D-599  Gear Shift Control Module "A" Performance  P0861-597  Gear Shift Control Module "A" Communication Circuit Low  P0862-598  Gear Shift Control Module "A" Communication Circuit High  


DESCRIPTION

When a signal is input from the P position switch (transmission shift main switch) or shift lever, the hybrid vehicle control ECU transmits a P position control (PCON) signal to the transmission control ECU assembly. Based on this signal, the transmission control ECU assembly actuates the shift control actuator assembly in order to mechanically lock or unlock the counter drive gear in the hybrid vehicle transaxle assembly.

P position state (engaged or released) of the actuator assembly is sent to the hybrid vehicle control ECU as a P position (PPOS) signal.

A384196E02
5.563,0.281 5.844,0.281 5.844,0.281 6.156,1.281 false 0.042,1.135 1.573,1.333 1.531,0.198 10 false P Position Switch 0.219,2.031 1.135,2.229 0.917,0.198 10 false Shift Lever 1.635,1.917 2.563,2.51 0.927,0.594 10 false Hybrid Vehicle Control ECU 2.708,1.125 3.625,1.323 0.917,0.198 10 false PCON signal 2.781,1.604 3.698,1.802 0.917,0.198 10 false PPOS signal 3.344,1.917 4.656,2.479 1.313,0.563 10 false Transmission Control ECU Assembly 4.427,1.125 5.802,1.323 1.375,0.198 10 false Actuator Energized 4.438,1.604 5.781,1.802 1.344,0.198 10 false Motor Position signal 3.604,0.167 5.594,0.531 1.99,0.365 10 false Shift Control Actuator Assembly 5.885,1.688 7.156,2.344 1.271,0.656 10 false Hybrid Vehicle Transaxle Assembly 0.677,3.229 3.583,3.573 2.906,0.344 10 false Certification ECU (Smart Key ECU Assembly)

DTC No. INF Code DTC Detection Condition Trouble Area
P085D 582 P position (PPOS) signal is logically inconsistent
·

Wire harness or connector

·

Transmission control ECU assembly

·

Hybrid vehicle control ECU


599 P position (PPOS) signal malfunction (output pulse is abnormal)
P0861 597 GND short in P position (PPOS) signal circuit
P0862 598 +B short in P position (PPOS) signal circuit

WIRING DIAGRAM

A384197E04
1.052,2.677 2.885,3.094 1.833,0.417 10 false Hybrid Vehicle Control ECU 1.052,2.521 1.667,2.719 0.615,0.198 10 false L5 2.073,1.021 2.688,1.219 0.615,0.198 10 false PCON 2.094,1.719 2.708,1.917 0.615,0.198 10 false PPOS 2.563,0.927 2.719,1.135 0.156,0.208 10 false 8 2.552,1.604 2.865,1.802 0.313,0.198 10 false 15 0.698,4.354 4.219,4.552 3.521,0.198 10 false Certification ECU (Smart Key ECU Assembly) 0.719,4.188 1.333,4.385 0.615,0.198 10 false L197 2.104,3.792 2.719,3.99 0.615,0.198 10 false PPOS 4.563,0.917 4.875,1.115 0.313,0.198 10 false 22 4.573,1.625 4.885,1.823 0.313,0.198 10 false 23 4.802,0.99 5.417,1.188 0.615,0.198 10 false PCON 4.813,1.698 5.427,1.896 0.615,0.198 10 false PPOS 4.646,2.958 5.979,3.354 1.333,0.396 10 false Transmission Control ECU Assembly 4.344,2.958 4.802,3.156 0.458,0.198 10 false A24 2.563,3.688 2.875,3.885 0.313,0.198 10 false 25

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 10 seconds or more.

2.

Depress the brake pedal, move the shift lever to N, and wait for 10 seconds or more.

3.

Push the transmission shift main switch (P position switch) and wait for 10 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (TRANSMISSION CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Chassis / Transmission Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Electronic shift lever system DTCs are not output. A
Any of the following DTCs are output. B


DTC No. Relevant Diagnosis
C2309 Open in B+ Circuit
C2311 Communication Error from HV ECU


e.

Turn the power switch off.



A

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL ECU ASSEMBLY)

B

2.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - TRANSMISSION CONTROL ECU ASSEMBLY)
a.

Disconnect the L5 hybrid vehicle control ECU connector.


b.

Disconnect the A24 transmission control ECU assembly connector.


c.

Disconnect the L197 certification ECU (smart key ECU assembly) connector.


d.

Turn the power switch on (IG).


e.

Measure the voltage according to the value(s) in the table below.

U190785E02
1.844,1.906 1.698,2.302 true 2.115,1.906 2.406,2.302 true 4.156,1.615 3.833,2.01 true 4.26,1.625 4.552,2.01 true 6.042,1.677 5.719,2.083 true 0.24,0.052 0.573,0.323 0.333,0.271 10 false *a 3.448,0.115 3.781,0.385 0.333,0.271 10 false *b 5.292,0.083 5.625,0.354 0.333,0.271 10 false *c 1.521,2.302 2.021,2.531 0.5,0.229 10 false PPOS 2.219,2.292 2.719,2.521 0.5,0.229 10 false PCON 1.906,0.469 2.125,0.646 0.219,0.177 10 false L5 5.521,2.083 6.021,2.313 0.5,0.229 10 false PPOS 3.646,2.01 4.146,2.24 0.5,0.229 10 false PCON 3.938,0.552 4.302,0.729 0.365,0.177 10 false A24 5.833,0.563 6.198,0.74 0.365,0.177 10 false L197 4.385,2.01 4.885,2.24 0.5,0.229 10 false PPOS

Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Front view of wire harness connector
(to Transmission Control ECU Assembly)
*c Rear view of wire harness connector Certification ECU (Smart Key ECU Assembly) - -

Standard Voltage:
Tester Connection Condition Specified Condition
A24-22 (PCON) - Body ground Power switch on (IG) Below 1 V
A24-23 (PPOS) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the hybrid vehicle control ECU connectors disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Turn the power switch off.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L5-8 (PCON) - A24-22 (PCON) Power switch off Below 1 Ω
L5-15 (PPOS) - A24-23 (PPOS) Power switch off Below 1 Ω
A24-23 (PPOS) - L197-25 (PPOS) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L5-8 (PCON) or A24-22 (PCON) - Body ground and other terminals Power switch off 10 kΩ or higher
L5-15 (PPOS), A24-23 (PPOS) or L197-25 (PPOS) - Body ground and other terminals Power switch off 10 kΩ or higher



h.

Connect the certification ECU (smart key ECU assembly) connector.


i.

Reconnect the A24 transmission control ECU assembly connector.


j.

Reconnect the L5 hybrid vehicle control ECU connector.



OK

3.CHECK HYBRID VEHICLE CONTROL ECU (PCON SIGNAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HYBRID VEHICLE CONTROL ECU (PCON SIGNAL)
a.

Turn the power switch on (IG).


b.
A379077E02
1.875,1.75 2.25,2 0.375,0.25 2.208,1.135 2.406,0.479 false 1.844,1.063 1.51,0.469 false 0.115,0.083 0.656,0.354 0.542,0.271 10 false *a 2.458,0.354 3,0.625 0.542,0.271 10 false PCON 1.302,0.354 1.844,0.625 0.542,0.271 10 false E1 1.979,1.792 2.521,2.063 0.542,0.271 10 false L5 2.844,3.406 3.385,3.677 0.542,0.271 10 false GND

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal L5-8 (PCON) - L5-6 (E1)
Equipment Setting 10V/DIV., 10ms/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
P position control (PCON) signal waveform appears. A
P position control (PCON) signal waveform does not appear. B


Text in Illustration
*a Component with harness connected
(Hybrid Vehicle Control ECU)


c.

Turn the power switch off.



A

4.CHECK HYBRID VEHICLE CONTROL ECU (PPOS SIGNAL)

B

4.CHECK HYBRID VEHICLE CONTROL ECU (PPOS SIGNAL)
a.

Turn the power switch on (IG).


b.
A379078E02
1.958,1.75 2.333,2 0.375,0.25 1.875,1.177 2.052,0.563 false 1.833,1.104 1.583,0.51 false 2.844,3.51 3.271,3.719 0.427,0.208 10 false GND 0.125,0.104 0.552,0.313 0.427,0.208 10 false *a 2.094,0.417 2.583,0.625 0.49,0.208 10 false PPOS 1.385,0.396 1.813,0.604 0.427,0.208 10 false E1 2.063,1.792 2.49,2 0.427,0.208 10 false L5

Connect an oscilloscope between the hybrid vehicle control ECU terminals specified in the table below, and measure the waveform.

Item Content
Terminal L5-15 (PPOS) - L5-6 (E1)
Equipment Setting 10V/DIV., 10ms/DIV.
Condition Power switch on (IG)

Result:
Result Proceed to
P position (PPOS) signal waveform appears A
P position (PPOS) signal waveform does not appear B


Text in Illustration
*a Component with harness connected
(Hybrid vehicle control ECU)


c.

Turn the power switch off.



A

5.REPLACE HYBRID VEHICLE CONTROL ECU

B

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

5.REPLACE HYBRID VEHICLE CONTROL ECU

NEXT

6.CLEAR DTC
6.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

7.CHECK DTC OUTPUT (HYBRID CONTROL)
7.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG) and leave the vehicle as it is for 10 seconds.


c.

Depress the brake pedal, move the shift lever to N and leave the vehicle as it is for 10 seconds.


d.

Push the P position switch (transmission shift main switch) and leave the vehicle as it is for 10 seconds.


e.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


f.

Check if DTCs are output.

Result:
Result Proceed to
No DTCs are output. A
P085D-582, P085D-599, P0861-597 or P0862-598 is output again. B



g.

Turn the power switch off.



A

COMPLETED

B

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY