Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3107-213  Lost Communication with Airbag System Control Module  


DESCRIPTION

The hybrid vehicle control ECU detects a problem in the collision signal line from the airbag ECU assembly and alerts the driver.


DTC No. INF Code DTC Detection Condition Trouble Area
P3107 213 Short to GND in the communication circuit
·

Wire harness or connector

·

Airbag ECU assembly

·

Hybrid vehicle control ECU



WIRING DIAGRAM

A254875E93
4.906,1 5.323,1.156 0.417,0.156 10 false ABFS 1.927,1 2.375,1.156 0.448,0.156 10 false GSW2 2.156,1.302 2.365,1.458 0.208,0.156 10 false E1 4.656,1 4.854,1.156 0.198,0.156 10 false 14 4.698,2.115 5.094,2.281 0.396,0.167 10 false L6 4.688,2.271 6.813,2.458 2.125,0.188 10 false Hybrid Vehicle Control ECU 0.969,2.073 1.323,2.26 0.354,0.188 10 false L16 0.958,2.25 2.563,2.448 1.604,0.198 10 false Airbag ECU Assembly 2.396,1 2.604,1.156 0.208,0.156 10 false 14 2.396,1.302 2.604,1.458 0.208,0.156 10 false 25

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 15 seconds or more.



PROCEDURE

1.CHECK DTC OUTPUT (SRS AIRBAG)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / SRS Airbag / Trouble Codes.


d.

Check if DTCs are output.


Result:
Result Proceed to
Airbag system DTCs are not output. A
Airbag system DTCs are output. B


e.

Turn the power switch off.



A

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)

B

2.CHECK AIRBAG ECU ASSEMBLY (CHECK WAVEFORM)
a.

Connect an oscilloscope between the airbag ECU assembly terminals specified in the table below.


b.

Turn the power switch on (READY).


c.
U190571E03
1.083,1.146 0.323,1.688 false 1.135,1.052 1.771,1.698 false 0.125,0.052 0.385,0.229 0.26,0.177 10 false *a 1.635,1.719 2.073,1.896 0.438,0.177 10 false GSW2 0.198,1.719 0.458,1.896 0.26,0.177 10 false E1 2.906,3.365 3.344,3.542 0.438,0.177 10 false GND 1.021,1.708 1.292,1.875 0.271,0.167 10 false L16

Measure the waveform.

Item Contents
Terminal L16-14 (GSW2) - L16-25 (E1)
Equipment Setting 5V/DIV., 500ms/DIV.
Condition Power switch on (READY)

Result:
Result Proceed to
The waveform appears as shown in the illustration. A
The waveform differs from the one shown in the illustration. B


Text in Illustration
*a Component with harness connected
(Airbag ECU Assembly)


d.

Turn the power switch off.



A

3.CLEAR DTC

B

6.CHECK AIRBAG ECU ASSEMBLY
3.CLEAR DTC

NEXT

4.CHECK DTC OUTPUT (HYBRID CONTROL)
4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P3107-213 is not output. A
DTC P3107-213 is output. B



e.

Turn the power switch off.



A

5.CHECK FOR INTERMITTENT PROBLEMS

B

5.CHECK FOR INTERMITTENT PROBLEMS

OK

NG

REPAIR OR REPLACE MALFUNCTIONING PARTS, COMPONENT AND AREA

6.CHECK AIRBAG ECU ASSEMBLY
a.

Disconnect the L16 airbag ECU assembly connector.


b.
U190705E03
1.177,1.125 0.563,1.729 false 1.24,1.021 1.677,1.667 false 0.177,0.094 0.427,0.313 0.25,0.219 10 false *a 1.688,1.646 2.188,1.865 0.5,0.219 10 false GSW2 0.385,1.729 0.635,1.948 0.25,0.219 10 false E1 1.073,0.344 1.344,0.51 0.271,0.167 10 false L16

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L16-14 (GSW2) - L16-25 (E1) Power switch off 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(Airbag ECU Assembly)


c.

Reconnect the L16 airbag ECU assembly connector.



OK

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG ECU ASSEMBLY)

NG

7.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - AIRBAG ECU ASSEMBLY)
a.

Disconnect the L6 hybrid vehicle control ECU connector.


b.

Disconnect the L16 airbag ECU assembly connector.


c.
U191173E02
2.604,1.896 2.208,2.188 false 1.24,3.958 1.74,4.333 false 0.021,0.031 0.292,0.229 0.271,0.198 10 false *a 0.042,2.469 0.313,2.667 0.271,0.198 10 false *b 2.01,1.802 2.302,1.969 0.292,0.167 10 false L6 0.417,3.823 0.719,3.99 0.302,0.167 10 false L16 1.823,2.135 2.292,2.333 0.469,0.198 10 false ABFS 1.76,4.271 2.396,4.49 0.635,0.219 10 false GSW2

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L6-14 (ABFS) or L16-14 (GSW2) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Hybrid Vehicle Control ECU)
*b Rear view of wire harness connector
(to Airbag ECU Assembly)


d.

Reconnect the L16 airbag ECU assembly connector.


e.

Reconnect the L6 hybrid vehicle control ECU connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR