Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3108-536  Lost Communication with A/C System Control Module  


DESCRIPTION

The power management control ECU detects a wiring malfunction in the serial communication line between it and the compressor with motor assembly.


DTC No. INF Code DTC Detection Condition Trouble Area
P3108 536 A/C inverter malfunction
·

Wire harness or connector

·

Compressor with motor assembly

·

Power management control ECU



WIRING DIAGRAM

A379091E01
1.375,0.635 1.865,0.906 0.49,0.271 10 false IG1 2.167,0.698 2.656,0.969 0.49,0.271 10 false CLK 2.208,1.167 2.698,1.438 0.49,0.271 10 false DIN 2.083,1.635 2.573,1.906 0.49,0.271 10 false DOUT 2.135,2.125 2.625,2.396 0.49,0.271 10 false STBI 2.125,2.542 2.615,2.813 0.49,0.271 10 false GND 1.177,0.51 1.667,0.781 0.49,0.271 10 false 6 2.521,0.698 3.01,0.969 0.49,0.271 10 false 1 2.521,1.167 3.01,1.438 0.49,0.271 10 false 2 2.531,1.635 3.021,1.906 0.49,0.271 10 false 3 2.531,2.125 3.021,2.396 0.49,0.271 10 false 4 2.531,2.448 3.021,2.719 0.49,0.271 10 false 5 1.323,2.927 1.813,3.198 0.49,0.271 10 false D12 1.323,3.083 2.417,3.49 1.094,0.406 10 false Compressor with Motor Assembly 5.24,2.927 5.729,3.198 0.49,0.271 10 false A21 5.24,3.083 6.49,3.479 1.25,0.396 10 false Power Management Control ECU 5.094,0.708 5.583,0.979 0.49,0.271 10 false 19 5.094,1.198 5.583,1.469 0.49,0.271 10 false 31 5.104,1.667 5.594,1.938 0.49,0.271 10 false 30 5.104,2.135 5.594,2.406 0.49,0.271 10 false 20 1.573,1.615 2.063,1.885 0.49,0.271 10 false +B 0.594,0.781 1.083,1.052 0.49,0.271 10 false A/C 5.333,1.198 5.823,1.469 0.49,0.271 10 false ITE 5.333,1.656 5.823,1.927 0.49,0.271 10 false ETI 1.583,2.083 2.073,2.354 0.49,0.271 10 false +B 5.344,2.115 5.833,2.385 0.49,0.271 10 false STB 5.323,0.719 5.813,0.99 0.49,0.271 10 false CLK 5.823,0.604 6.313,0.875 0.49,0.271 10 false +B 5.802,1.115 6.292,1.385 0.49,0.271 10 false +B

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Wait for 30 seconds or more with the power switch on (READY) and the air conditioning turned off.

2.

Turn the air conditioning on and wait for 30 seconds or more.



PROCEDURE

1.CHECK CONNECTOR CONNECTION CONDITION (POWER MANAGEMENT CONTROL ECU CONNECTOR)

OK

2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)

NG

CONNECT SECURELY

2.CHECK CONNECTOR CONNECTION CONDITION (COMPRESSOR WITH MOTOR ASSEMBLY CONNECTOR)
a.
U190605E02
2.25,0.271 2.573,0.438 0.323,0.167 10 false D12

Check the connection of connector D12 of the compressor with motor assembly.

OK:

The connector is connected securely and there are no contact problems.




OK

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (COMPRESSOR WITH MOTOR ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the D12 compressor with motor assembly connector.


b.
U110453E02
1.896,1.135 2.031,1.667 false 2.042,1.146 2.458,1.677 false 0.24,0.188 0.469,0.365 0.229,0.177 10 false *a 0.469,1.063 0.74,1.229 0.271,0.167 10 false D12 1.958,1.698 2.292,1.865 0.333,0.167 10 false GND 2.5,1.698 2.76,1.865 0.26,0.167 10 false IG1

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D12-5 (GND) - Body ground Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D12-6 (IG1) - D12-5 (GND) Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Reconnect the D12 compressor with motor assembly connector.



OK

4.CHECK DTC OUTPUT (HYBRID CONTROL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P3108-536 is output. A
DTC P3108-536 is not output. B



e.

Turn the power switch off.



A

5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)

B

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)
5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)
a.

Disconnect the A21 power management control ECU connector.


b.

Disconnect the D12 compressor with motor assembly connector.


c.

Turn the power switch on (IG).


d.
U154258E03
0.99,1.979 1.292,1.677 false 0.948,2.042 1.292,1.958 false 0.896,2.042 1.292,2.25 false 1.323,3.75 1.063,4.271 false 1.594,3.75 1.854,4.271 false 1.448,3.76 1.448,4.271 false 0.188,1.865 0.458,2.031 0.271,0.167 10 false A21 0.5,3.677 0.771,3.844 0.271,0.167 10 false D12 0.167,0.156 0.344,0.323 0.177,0.167 10 false *a 0.167,3.021 0.344,3.188 0.177,0.167 10 false *b 1.354,1.552 1.667,1.719 0.313,0.167 10 false CLK 1.365,1.875 1.677,2.042 0.313,0.167 10 false ETI 1.354,2.208 1.667,2.375 0.313,0.167 10 false ITE 0.885,4.302 1.198,4.469 0.313,0.167 10 false CLK 1.365,4.302 1.646,4.469 0.281,0.167 10 false DIN 1.823,4.302 2.25,4.469 0.427,0.167 10 false DOUT

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-19 (CLK) - Body ground Power switch on (IG) Below 1 V
A21-30 (ETI) - Body ground Power switch on (IG) Below 1 V
A21-31 (ITE) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Compressor with Motor Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector and the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A21-19 (CLK) - D12-1 (CLK) Power switch off Below 1 Ω
A21-30 (ETI) - D12-3 (DOUT) Power switch off Below 1 Ω
A21-31 (ITE) - D12-2 (DIN) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A21-19 (CLK) or D12-1 (CLK) - Body ground and other terminals Power switch off 10 kΩ or higher
A21-30 (ETI) or D12-3 (DOUT) - Body ground and other terminals Power switch off 10 kΩ or higher
A21-31 (ITE) or D12-2 (DIN) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the D12 compressor with motor assembly connector.


h.

Reconnect the A21 power management control ECU connector.



OK

6.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK POWER MANAGEMENT CONTROL ECU
a.

Disconnect the D12 compressor with motor assembly connector.


b.
U110454E02
1.333,1.125 1.042,1.708 false 1.656,1.135 1.948,1.719 false 1.49,1.146 1.49,1.719 false 0.167,0.156 0.375,0.333 0.208,0.177 10 false *a 0.417,1.031 0.688,1.198 0.271,0.167 10 false D12 0.813,1.75 1.135,1.917 0.323,0.167 10 false CLK 1.385,1.75 1.708,1.917 0.323,0.167 10 false DIN 1.917,1.75 2.344,1.917 0.427,0.167 10 false DOUT

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D12-3 (DOUT) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D12-1 (CLK) - Body ground Power switch on (IG) 11 to 14 V
D12-2 (DIN) - Body ground Power switch on (IG) 11 to 14 V
D12-3 (DOUT) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Reconnect the D12 compressor with motor assembly connector.



OK

7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

7.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
a.

Disconnect the A21 power management control ECU connector.


b.
U154236E03
0.969,2.51 1.344,2.219 false 0.927,2.573 1.375,2.427 false 0.875,2.573 1.344,2.813 false 0.76,2.99 1.031,3.156 0.271,0.167 10 false A21 1.385,2.104 1.708,2.271 0.323,0.167 10 false CLK 1.406,2.344 1.729,2.51 0.323,0.167 10 false ETI 1.396,2.76 1.719,2.927 0.323,0.167 10 false ITE 0.26,0.271 0.417,0.438 0.156,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-19 (CLK) - Body ground Power switch off 10 kΩ or higher
A21-31 (ITE) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-30 (ETI) - Body ground Power switch on (IG) 11 to 14 V
A21-19 (CLK) - Body ground Power switch on (IG) Below 1 V
A21-31 (ITE) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Reconnect the A21 power management control ECU connector.



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY

8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - COMPRESSOR WITH MOTOR)
a.

Disconnect the A21 power management control ECU connector.


b.

Disconnect the D12 compressor with motor assembly connector.


c.

Turn the power switch on (IG).


d.
U154259E03
0.948,1.979 1.365,1.792 false 1.74,3.771 2,4.292 false 1.24,2.125 1.51,2.292 0.271,0.167 10 false A21 0.49,3.667 0.76,3.833 0.271,0.167 10 false D12 0.135,0.156 0.313,0.323 0.177,0.167 10 false *a 0.135,3.021 0.313,3.188 0.177,0.167 10 false *b 1.406,1.688 1.719,1.854 0.313,0.167 10 false STB 1.927,4.302 2.354,4.469 0.427,0.167 10 false STBI

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-20 (STB) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)
*b Front view of wire harness connector
(to Compressor with Motor Assembly)

NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A21-20 (STB) - D12-4 (STBI) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A21-20 (STB) or D12-4 (STBI) - Body ground and other terminals Power switch off 10 kΩ or higher



g.

Reconnect the D12 compressor with motor assembly connector.


h.

Reconnect the A21 power management control ECU connector.



OK

9.CHECK POWER MANAGEMENT CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

9.CHECK POWER MANAGEMENT CONTROL ECU
a.

Disconnect the D12 compressor with motor assembly connector.


b.
U110455E03
1.76,1.125 1.906,1.656 false 0.24,0.188 0.469,0.365 0.229,0.177 10 false *a 0.469,1.073 0.74,1.24 0.271,0.167 10 false D12 1.844,1.698 2.25,1.865 0.406,0.167 10 false STBI

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D12-4 (STBI) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Compressor with Motor Assembly)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D12-4 (STBI) - Body ground Power switch on (IG) Below 1 V


NOTICE:

Turning the power switch on (IG) with the compressor with motor assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Reconnect the D12 compressor with motor assembly connector.



OK

10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY

NG

10.CHECK COMPRESSOR WITH MOTOR ASSEMBLY
a.

Disconnect the A21 power management control ECU connector.


b.
U154237E03
0.917,2.5 1.406,2.323 false 0.76,3 1.031,3.167 0.271,0.167 10 false A21 1.438,2.229 1.76,2.396 0.323,0.167 10 false STB 0.26,0.271 0.417,0.438 0.156,0.167 10 false *a

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A21-20 (STB) - Body ground Power switch off 10 kΩ or higher


Text in Illustration
*a Rear view of wire harness connector
(to Power Management Control ECU)


c.

Turn the power switch on (IG).


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A21-20 (STB) - Body ground Power switch on (IG) 11 to 14 V


NOTICE:

Turning the power switch on (IG) with the power management control ECU connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



e.

Turn the power switch off.


f.

Reconnect the A21 power management control ECU connector.



OK

NG

REPLACE COMPRESSOR WITH MOTOR ASSEMBLY