Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2012.10–2014.11
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P3147-239  Transmission system  P3147-241  Transmission system  


DESCRIPTION

The hybrid vehicle transaxle assembly consists of the power split planetary gear unit, MG1, MG2, and the motor speed reduction planetary gear unit. The power split planetary gear unit uses a planetary gear to split engine output in accordance with driving requests while the vehicle is driven or the HV battery is charged. MG2 assists engine output while increasing vehicle drive force. MG2 also converts the energy, which would otherwise be consumed in the form of heat during normal braking, into electrical energy. This recovered energy is put back into the HV battery to perform regenerative braking. MG1 generates power, which is used for charging the HV battery or driving MG2, and also regulates the amount of electricity being generated. In addition, MG1 is used as a starter motor to start the engine.

DTC No. INF Code DTC Detection Condition Trouble Area
P3147 239 Hybrid vehicle transaxle input malfunction (shaft damaged)
·

Engine

·

Hybrid vehicle transaxle assembly

·

Power management control ECU

·

Transmission input damper assembly


241 Hybrid vehicle transaxle input malfunction (input system lock)

CAUTION / NOTICE / HINT

HINT:
·

If DTC P3147-239 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

Drive the vehicle at approximately 12 mph (30 km/h) or more for approximately 5 seconds or more using the engine.


·

If DTC P3147-241 is output, clear the DTCs, perform the following procedure, and check that the same DTC is not output after the repair.

(a)

With the vehicle stopped and the park (P) selected, turn the power switch on (READY) and gradually depress the accelerator pedal so that the engine starts.




PROCEDURE

1.CHECK DTC OUTPUT (ENGINE AND ECT)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
SFI system DTCs are not output. A
SFI system DTCs are output. B



e.

Turn the power switch off.



A

2.CHECK DTC OUTPUT (HYBRID CONTROL)

B

2.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTCs other than P3147-239 or P3147-241 are not output. A
DTC P3147-240 or P3147-242 is also output. B
DTC P0A1D is also output. C



e.

Turn the power switch off.



A

3.CHECK CRANKSHAFT PULLEY REVOLUTION (PARK (P) SELECTED)

B

C

3.CHECK CRANKSHAFT PULLEY REVOLUTION (PARK (P) SELECTED)
a.

Turn the power switch off.


b.

Push the P position switch and lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch off before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


Result:
Result Proceed to
The crankshaft rotates. A
The crankshaft does not rotate. B



d.

Lower the vehicle.



A

4.CLEAR DTC

B

8.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
4.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

5.CHECK ENGINE RACING
6.CHECK CREEP MOVEMENT
a.

Turn the power switch on (READY).


b.

Depress the brake pedal, move the shift lever to D, and release the brake pedal.

OK:

The wheels turn (the vehicle creeps forward).


HINT:

If the wheels do not turn and the reading on the GTS shows DTC P3147-239, replace the hybrid vehicle transaxle assembly.



c.

Turn the power switch off.



OK

7.CHECK ENGINE SPEED

NG

8.CHECK CRANKSHAFT PULLEY REVOLUTION (N POSITION)
a.

Turn the power switch on (IG) and move the shift lever to N.


b.

Lift up the vehicle.


c.

Turn the crankshaft pulley using hand tools to check if the crankshaft can rotate smoothly.

CAUTION:

Do not turn the power switch on (READY) while performing this inspection. Be sure to turn the power switch on (IG) before performing this inspection, to prevent the engine from starting.


NOTICE:

Engine compression causes resistance when turning the crankshaft pulley. Check if the crankshaft rotates smoothly (or if it is locked) by manually applying sufficient torque to turn the crankshaft pulley. The torque required to turn the crankshaft pulley should be the same as for a known good vehicle of the same type.


OK:

The crankshaft rotates.



d.

Lower the vehicle.


e.

Turn the power switch off.



OK

NG

REPAIR OR REPLACE ENGINE