Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › 2014.11–2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P0D2F-266  Drive Motor "A" Inverter Voltage Sensor Circuit Low  P0D30-267  Drive Motor "A" Inverter Voltage Sensor Circuit High  


DESCRIPTION

The inverter contains a three-phase bridge circuit, which consists of six power transistors (IGBTs) each for MG1 and MG2. The inverter converts high-voltage direct current from the HV battery into three-phase alternating current for MG1 and MG2; it also converts three-phase alternating current supplied by MG1 and MG2 into direct current for the HV battery. The MG ECU controls the actuation of the power transistors (IGBTs). The inverter transmits information necessary for control, such as amperage and voltage, to the MG ECU.

A259399E22
1.323,0.865 1.771,1.104 0.448,0.24 10 false MG1 3.917,0.854 4.365,1.094 0.448,0.24 10 false MG2 1.208,1.458 1.51,1.74 0.302,0.281 10 false U 1.5,1.469 1.833,1.771 0.333,0.302 10 false V 1.823,1.458 2.063,1.719 0.24,0.26 10 false W 3.844,1.479 4.146,1.76 0.302,0.281 10 false U 4.135,1.479 4.469,1.781 0.333,0.302 10 false V 4.458,1.479 4.698,1.74 0.24,0.26 10 false W 1.688,2.052 2.688,2.219 1,0.167 10 false Current Sensor 4.25,2.052 5.24,2.208 0.99,0.156 10 false Current Sensor 4.573,4.604 5.208,4.896 0.635,0.292 10 false Inverter 5.76,5.667 7.063,6.094 1.302,0.427 10 false Power Management Control ECU 0.323,6 1.031,6.385 0.708,0.385 10 false Boost Converter 0.094,7.281 1.344,7.75 1.25,0.469 10 false Inverter with Converter Assembly 1.583,8.292 2.354,8.531 0.771,0.24 10 false HV Battery 3.156,7.854 4.083,8.083 0.927,0.229 10 false A/C Inverter 3.073,6.042 3.729,6.281 0.656,0.24 10 false MG ECU 4.01,6.354 5.167,6.563 1.156,0.208 10 false DCDC Converter

The MG ECU uses an inverter voltage sensor, which is built into the inverter, to detect boosted high voltage to allow control of the voltage boost.

The MG ECU monitors the inverter voltage sensor and detects the following malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P0D2F 266 Short to GND in the inverter voltage (VH) signal line Inverter with converter assembly
P0D30 267 Open or short to +B in the inverter voltage (VH) signal line

CAUTION / NOTICE / HINT

HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (READY) and wait for 5 seconds or more.



PROCEDURE

1.REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS
a.

Refer to replace inverter with converter assembly parts (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>DTC CHECK / CLEAR).


HINT:

The signal line from the inverter voltage (VH) sensor is connected to the MG ECU inside the inverter with converter assembly.



NEXT

COMPLETED