Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1C2D-587  Hybrid Battery Voltage / DC/DC Converter Voltage Correlation  


DESCRIPTION

For a description of the boost converter (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>P0CA3-442).

The MG ECU uses a voltage sensor (VL) that is built into the boost converter to detect the high voltage before it is boosted. The ECU also uses the battery smart unit to detect HV battery voltage (VB).

HINT:

Using the GTS, check the Data List of Power Resource VB and Batt Pack Current Val. If these values are not within the below range, there is a battery smart unit malfunction.


A278556E03
1.719,0.094 6.156,0.385 4.438,0.292 10 false Power Resource VB to Batt Pack Current Val (20 to 40°C (68 to 104°F)) 0.396,1.292 1.948,1.594 1.552,0.302 10 false Power Resource VB (V) 3.188,2.417 5.167,2.677 1.979,0.26 10 false Batt Pack Current Val (A)

DTC No. INF Code DTC Detection Condition Trouble Area
P1C2D 587 Voltages from HV battery voltage (VB) sensor and boost converter voltage (VL) sensor deviate
·

Inverter with converter assembly

·

Battery smart unit



CAUTION / NOTICE / HINT

HINT:

When the accelerator pedal is not depressed with the power switch on (READY) and park (P) selected, if "VL-Voltage before Boosting" and the "Power Resource VB" is approximately same after repair, the condition is judged as normal.


PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
DTC P1C2D-587 only is output. Alternatively, P1C2D- 587 and any DTCs other than P0B23-129, P0CA3-442 or P0E32-585 are output. A
P1C2D-587 and P0B23-129 (Hybrid Battery Pack Sensor Module) are output. B
P1C2D-587 and P0C3A-442 (abnormal voltage execution value) are output. C
P1C2D-587 and P0E32-585 (boost converter voltage (VL) sensor performance problem) are output. D



e.

Turn the power switch off.



A

2.CLEAR DTC

B

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

D

2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

3.CHECK DTC OUTPUT (HYBRID CONTROL)
3.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3. (*1)


b.

Turn the power switch on (READY). (*2)


c.

Enter the following menus: Powertrain / Hybrid Control / Data List (*3)


d.

If both "Power Resource VB" and "VL-Voltage before Boosting" are less than 208 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 208 V or more. (*4)


e.

Push the P position switch. (*5)


f.

Set the air conditioning to MAX COOL and turn the headlights on. (*6)


g.

Confirm that "Batt Pack Current Val" is more than 3 A. (*7)


h.

Leave the vehicle for 15 seconds with the engine stopped during steps (*5) (*6) and (*7). (*8)


i.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. (*9)


j.

Check if DTCs are output. (*10)

NOTICE:

If the low HV battery charge warning light comes on, push the P position switch and start the engine to charge the HV battery. After the engine stops, perform steps (*1) through (*10) again.


Result:
Result Proceed to
No DTCs are output, or DTCs other than the following are output. A
P0B23-129 (Hybrid Battery Pack Sensor Module) is output. B
P0E32-585 (boost converter voltage (VL) sensor performance problem) is output. C
P3000-388 (discharge inhibition) is output. D
P3004-132 (high voltage power supply line problem) is output. E



k.

Turn the power switch off.



A

4.CHECK DTC OUTPUT (HYBRID CONTROL)

B

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

D

LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS (*1) THROUGH (*10))

E

4.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Turn the power switch on (READY). (*11)


b.

Perform a road test that repeats full acceleration to 60 km/h (37 mph) and then braking to a complete stop three times. (*12)


c.

Connect the GTS to the DLC3. (*13)


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes. (*14)


e.

Check if DTCs are output. (*15)

Result:
Result Proceed to
No DTCs are output, or DTCs other than the following are output. A
P0B23-129 (HV battery voltage circuit malfunction) is output. B
P0E32-585 (boost converter voltage (VL) sensor performance problem) is output. C
P3000-388 (discharge inhibition) is output. D
P3004-132 (high voltage power supply line problem) is output. E



f.

Turn the power switch off.



A

5.READ VALUE USING GTS

B

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

D

LEAVE VEHICLE WITH PARK (P) SELECTED, AND CHARGE HV BATTERY BY IDLING UNTIL IDLING STOPS (PERFORM STEPS (*11) THROUGH (*15))

E

5.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List.


d.

Select "Power Resource VB", "VL-Voltage before Boosting" and "VH-Voltage after Boosting" in the Data List.


e.

If both "Power Resource VB" and "VL-Voltage before Boosting" are less than 208 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 208 V or more.


f.

Turn the engine off, push the P position switch, and read the Data List when the vehicle is stationary.

Result:
Result Proceed to
Both of the following are not satisfied. A
Both of the following are satisfied:
·

Difference between "Power Resource VB" and "VH-Voltage after Boosting" is less than 5 V.

·

Difference between "VL-Voltage before Boosting" and "VH-Voltage after Boosting" is more than 35 V.


B
Both of the following are satisfied:
·

Difference between "VH-Voltage after Boosting" and "VL-Voltage before Boosting" is less than 5 V.

·

Difference between "Power Resource VB" and "VH-Voltage after Boosting" is more than 15 V.


C



g.

Turn the power switch off.



A

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

C

6.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P1C2D-587.

Result:
Result Proceed to
Both of the following are satisfied or both of the following are not satisfied. A
"Power Resource VB" is less than 168 V or more than 240 V. B
"VL-Voltage before Boosting" is less than 168 V or more than 240 V. C



e.

Turn the power switch off.



A

7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)

B

C

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

7.CHECK FREEZE FRAME DATA (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Read the freeze frame data of DTC P1C2D-587.

HINT:

In the freeze frame data, read the "Power Resource VB" and all of the "Battery Block Vol".


Result:
Result Proceed to
Others (Freeze frame data is not stored). A
Both of the following are satisfied:
·

Sum of all "Battery Block Vol" is more than ("Power Resource VB" - 25 V)

·

Sum of all "Battery Block Vol" is less than ("Power Resource VB" + 20 V)


B
Neither A nor B is satisfied. C



e.

Turn the power switch off.



A

8.READ VALUE USING GTS

B

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

C

8.READ VALUE USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (READY).


c.

Enter the following menus: Powertrain / Hybrid Control / Data List.


d.

If both "Power Resource VB" and "VL-Voltage before Boosting" are less than 208 V, move the shift lever to D and depress both the accelerator pedal and brake pedal at the same time to raise them to 208 V or more.


e.

Turn the engine off, push the P position switch, and read the "Power Resource VB" and all of the "Battery Block Vol", when the vehicle is stationary.

Result:
Result Proceed to
Both of the following are satisfied:
·

Sum of all "Battery Block Vol" is more than ("Power Resource VB" - 25 V)

·

Sum of all "Battery Block Vol" is less than ("Power Resource VB" + 20 V)


A
The preceding condition is not satisfied. B



f.

Turn the power switch off.



A

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

B