Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › HYBRID CONTROL SYSTEM › from 2016.05
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301573 HYBRID CONTROL SYSTEM C

HYBRID / BATTERY CONTROL  HYBRID CONTROL SYSTEM  P1CAC-200  Generator Position Sensor Angle Malfunction  P1CAF-792  Generator Position Sensor REF Signal Cycle Malfunction  P1CB2-793  Generator Position Sensor REF Signal Stop Malfunction  


DESCRIPTION

The inverter with converter assembly (MG ECU) monitors its internal operation and detects the following malfunctions.

DTC No. INF Code DTC Detection Condition Trouble Area
P1CAC 200 The difference between the resolver angle for control and estimated resolver angle exceeds the allowable value.
·

Inverter with converter assembly

·

Hybrid vehicle transaxle assembly

·

Wire harness or connector


P1CAF 792 Resolver REF signal cycle error
P1CB2 793 Resolver REF signal oscillation stop error

WIRING DIAGRAM

A220049E22
1.875,3.021 2.01,3.208 0.135,0.188 10 false 1 1.875,3.656 2.01,3.844 0.135,0.188 10 false 2 1.854,4.313 1.99,4.5 0.135,0.188 10 false 3 1.865,1.271 2,1.458 0.135,0.188 10 false 1 1.865,1.604 2,1.792 0.135,0.188 10 false 4 1.854,1.917 1.99,2.104 0.135,0.188 10 false 2 1.865,2.25 2,2.438 0.135,0.188 10 false 5 1.885,0.604 2.021,0.792 0.135,0.188 10 false 3 1.865,0.948 2,1.135 0.135,0.188 10 false 6 0.25,5.427 2.521,5.625 2.271,0.198 10 false Hybrid Vehicle Transaxle Assembly 0.75,5.031 2.042,5.229 1.292,0.198 10 false Generator Resolver 0.74,2.656 1.771,2.854 1.031,0.198 10 false Motor Resolver 1.479,4.333 1.875,4.521 0.396,0.188 10 false GCS 1.5,3.667 1.875,3.854 0.375,0.188 10 false GSN 1.5,3.01 1.865,3.198 0.365,0.188 10 false GRF 1.385,4.656 1.823,4.844 0.438,0.188 10 false GCSG 1.385,4 1.833,4.188 0.448,0.188 10 false GSNG 1.396,3.344 1.854,3.531 0.458,0.188 10 false GRFG 1.479,1.948 1.875,2.135 0.396,0.188 10 false MCS 1.49,1.281 1.865,1.469 0.375,0.188 10 false MSN 1.49,0.646 1.854,0.833 0.365,0.188 10 false MRF 1.375,2.26 1.813,2.448 0.438,0.188 10 false MCSG 1.375,1.615 1.823,1.802 0.448,0.188 10 false MSNG 1.385,0.938 1.844,1.125 0.458,0.188 10 false MRFG 4.292,5.198 4.583,5.354 0.292,0.156 10 false D29 4.292,5.354 7.063,5.563 2.771,0.208 10 false Inverter with Converter Assembly (MG ECU) 5.281,4.438 5.677,4.625 0.396,0.188 10 false GCS 5.281,3.771 5.656,3.958 0.375,0.188 10 false GSN 5.281,3.115 5.646,3.302 0.365,0.188 10 false GRF 5.281,4.75 5.719,4.938 0.438,0.188 10 false GCSG 5.281,4.104 5.729,4.292 0.448,0.188 10 false GSNG 5.281,3.448 5.74,3.635 0.458,0.188 10 false GRFG 5.281,2.01 5.677,2.198 0.396,0.188 10 false MCS 5.281,1.344 5.656,1.531 0.375,0.188 10 false MSN 5.281,0.698 5.646,0.885 0.365,0.188 10 false MRF 5.281,2.333 5.719,2.521 0.438,0.188 10 false MCSG 5.281,1.688 5.729,1.875 0.448,0.188 10 false MSNG 5.281,1.021 5.74,1.208 0.458,0.188 10 false MRFG 5.281,2.688 5.719,2.875 0.438,0.188 10 false DRN6 5.031,3 5.229,3.188 0.198,0.188 10 false 11 5.073,3.667 5.208,3.854 0.135,0.188 10 false 7 5.073,3.979 5.208,4.167 0.135,0.188 10 false 8 5.083,4.635 5.219,4.823 0.135,0.188 10 false 9 0.75,2.5 1.063,2.688 0.313,0.188 10 false D1 0.75,4.885 1.063,5.073 0.313,0.188 10 false D7 1.865,3.313 2,3.5 0.135,0.188 10 false 5 1.865,3.979 2,4.167 0.135,0.188 10 false 6 1.875,4.646 2.01,4.833 0.135,0.188 10 false 7 5.063,0.604 5.198,0.792 0.135,0.188 10 false 1 5.052,0.927 5.188,1.115 0.135,0.188 10 false 2 5.063,1.26 5.198,1.448 0.135,0.188 10 false 3 5.073,1.594 5.208,1.781 0.135,0.188 10 false 4 5.063,2.24 5.198,2.427 0.135,0.188 10 false 5 5.063,1.906 5.198,2.094 0.135,0.188 10 false 6 5.01,3.323 5.208,3.51 0.198,0.188 10 false 12 5.01,4.313 5.208,4.5 0.198,0.188 10 false 10 5.031,2.594 5.229,2.781 0.198,0.188 10 false 13

CAUTION / NOTICE / HINT

CAUTION:
·

Before inspecting the high-voltage system or disconnecting the low voltage connector of the inverter with converter assembly, take safety precautions such as wearing insulated gloves and removing the service plug grip to prevent electrical shocks. After removing the service plug grip, put it in your pocket to prevent other technicians from accidentally reconnecting it while you are working on the high-voltage system.

·

After removing the service plug grip, wait for at least 10 minutes before touching any of the high-voltage connectors or terminals. After waiting for 10 minutes, check the voltage at the terminals in the inspection point in the inverter with converter assembly. The voltage should be 0 V before beginning work (See page Engine / Hybrid System>HYBRID / BATTERY CONTROL>HYBRID CONTROL SYSTEM>PRECAUTION).

HINT:

Waiting for at least 10 minutes is required to discharge the high-voltage capacitor inside the inverter with converter assembly.




NOTICE:

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


HINT:

After the repair, clear the DTCs and perform the following procedure to check that DTCs are not output.

1.

Turn the power switch on (IG) and wait for 5 seconds or more.

2.

Turn the power switch on (READY) with park (P) selected and wait for 5 seconds or more.

3.

Depress the accelerator pedal of the vehicle with the engine stopped and park (P) selected to start the engine.

4.

Keep the engine running for 5 seconds or more.

5.

Drive the vehicle forward with drive (D) selected for 5 m or more.

6.

Drive the vehicle backward with reverse (R) selected for 5 m or more.



PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
Only P1CAC-200, P1CAF-792 or P1CB2-793 is output, or DTCs other than the ones in the table below are also output. A
Any of the following DTCs are also output. B


DTC No. Relevant Diagnosis
P0A3F-243 Drive Motor "A" Position Sensor Circuit
P0A4B-253 Generator Position Sensor Circuit
P0A4C-513 Generator Position Sensor Circuit Range / Performance
P0A4D-255 Generator Position Sensor Circuit Low


e.

Turn the power switch off.



A

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

B

2.CHECK CONNECTOR CONNECTION CONDITION (INVERTER WITH CONVERTER ASSEMBLY CONNECTOR)

OK

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)

NG

CONNECT SECURELY

3.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - GENERATOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D29 inverter with converter assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U154357E03
1.656,1.896 0.938,2.677 false 1.5,1.885 0.917,2.229 false 1.479,1.719 0.896,1.844 false 1.969,1.729 2.531,1.75 false 1.792,1.729 2.531,1.375 false 1.646,1.719 2.531,0.979 false 0.156,0.146 0.458,0.354 0.302,0.208 10 false *a 0.417,1.833 0.792,2.031 0.375,0.198 10 false GSN 0.417,2.208 0.813,2.406 0.396,0.198 10 false GRF 0.417,2.656 0.938,2.854 0.521,0.198 10 false GRFG 2.604,0.792 3.052,0.99 0.448,0.198 10 false GSNG 2.604,1.25 3.073,1.448 0.469,0.198 10 false GCSG 2.604,1.677 3,1.875 0.396,0.198 10 false GCS 1.75,2.75 2.021,2.917 0.271,0.167 10 false D29

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D29-11 (GRF) - Body ground Power switch on (IG) Below 1 V
D29-12 (GRFG) - Body ground Power switch on (IG) Below 1 V
D29-7 (GSN) - Body ground Power switch on (IG) Below 1 V
D29-8 (GSNG) - Body ground Power switch on (IG) Below 1 V
D29-10 (GCS) - Body ground Power switch on (IG) Below 1 V
D29-9 (GCSG) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


g.

Turn the power switch off.


h.

Reconnect the D29 inverter with converter assembly connector.



OK

4.CHECK GENERATOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK GENERATOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D29 inverter with converter assembly connector.


c.
U154357E03
1.656,1.896 0.938,2.677 false 1.5,1.885 0.917,2.229 false 1.479,1.719 0.896,1.844 false 1.969,1.729 2.531,1.75 false 1.792,1.729 2.531,1.375 false 1.646,1.719 2.531,0.979 false 0.156,0.146 0.458,0.354 0.302,0.208 10 false *a 0.417,1.833 0.792,2.031 0.375,0.198 10 false GSN 0.417,2.208 0.813,2.406 0.396,0.198 10 false GRF 0.417,2.656 0.938,2.854 0.521,0.198 10 false GRFG 2.604,0.792 3.052,0.99 0.448,0.198 10 false GSNG 2.604,1.25 3.073,1.448 0.469,0.198 10 false GCSG 2.604,1.677 3,1.875 0.396,0.198 10 false GCS 1.75,2.75 2.021,2.917 0.271,0.167 10 false D29

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D29-11 (GRF) - D29-12 (GRFG) Power switch off 7.1 to 21.6 Ω
D29-7 (GSN) - D29-8 (GSNG) Power switch off 13.7 to 34.5 Ω
D29-10 (GCS) - D29-9 (GCSG) Power switch off 12.8 to 32.4 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D29-11 (GRF) or D29-12 (GRFG) - Body ground and other terminals Power switch off 1 MΩ or higher
D29-7 (GSN) or D29-8 (GSNG) - Body ground and other terminals Power switch off 1 MΩ or higher
D29-10 (GCS) or D29-9 (GCSG) - Body ground and other terminals Power switch off 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Reconnect the D29 inverter with converter assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)

NG

9.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
5.CHECK HARNESS AND CONNECTOR (INVERTER WITH CONVERTER ASSEMBLY - MOTOR RESOLVER)
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D29 inverter with converter assembly connector.


c.

Connect the cable to the negative (-) auxiliary battery terminal.


d.

Turn the power switch on (IG).


e.
U154358E03
1.5,1.573 0.792,1.542 false 1.479,1.406 0.969,1.01 false 1.635,1.396 1.469,0.51 false 1.667,1.573 2.25,0.542 false 1.813,1.583 2.5,0.979 false 1.969,1.583 2.5,1.604 false 0.177,0.115 0.51,0.354 0.333,0.24 10 false *a 1.573,2.833 1.844,3 0.271,0.167 10 false D29 0.333,1.469 0.76,1.698 0.427,0.229 10 false MSN 2.281,0.333 2.781,0.563 0.5,0.229 10 false MSNG 2.573,0.875 3.073,1.104 0.5,0.229 10 false MCSG 2.573,1.521 3.073,1.75 0.5,0.229 10 false MCS 0.552,0.833 0.979,1.063 0.427,0.229 10 false MRF 1.156,0.292 1.583,0.521 0.427,0.229 10 false MRFG

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D29-1 (MRF) - Body ground Power switch on (IG) Below 1 V
D29-2 (MRFG) - Body ground Power switch on (IG) Below 1 V
D29-3 (MSN) - Body ground Power switch on (IG) Below 1 V
D29-4 (MSNG) - Body ground Power switch on (IG) Below 1 V
D29-6 (MCS) - Body ground Power switch on (IG) Below 1 V
D29-5 (MCSG) - Body ground Power switch on (IG) Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)

NOTICE:

Turning the power switch on (IG) with the low voltage connector of the inverter with converter assembly disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



f.

Disconnect the cable from the negative (-) auxiliary battery terminal.


g.

Turn the power switch off.


h.

Reconnect the D29 inverter with converter assembly connector.



OK

6.CHECK MOTOR RESOLVER

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK MOTOR RESOLVER
CAUTION:

Be sure to wear insulated gloves.


a.

Check that the service plug grip is not installed.

NOTICE:

After removing the service plug grip, do not turn the power switch on (READY), unless instructed by the repair manual because this may cause a malfunction.



b.

Disconnect the D29 inverter with converter assembly connector.


c.
U154358E03
1.5,1.573 0.792,1.542 false 1.479,1.406 0.969,1.01 false 1.635,1.396 1.469,0.51 false 1.667,1.573 2.25,0.542 false 1.813,1.583 2.5,0.979 false 1.969,1.583 2.5,1.604 false 0.177,0.115 0.51,0.354 0.333,0.24 10 false *a 1.573,2.833 1.844,3 0.271,0.167 10 false D29 0.333,1.469 0.76,1.698 0.427,0.229 10 false MSN 2.281,0.333 2.781,0.563 0.5,0.229 10 false MSNG 2.573,0.875 3.073,1.104 0.5,0.229 10 false MCSG 2.573,1.521 3.073,1.75 0.5,0.229 10 false MCS 0.552,0.833 0.979,1.063 0.427,0.229 10 false MRF 1.156,0.292 1.583,0.521 0.427,0.229 10 false MRFG

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D29-1 (MRF) - D29-2 (MRFG) Power switch off 7.1 to 21.6 Ω
D29-3 (MSN) - D29-4 (MSNG) Power switch off 13.7 to 34.5 Ω
D29-6 (MCS) - D29-5 (MCSG) Power switch off 12.8 to 32.4 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D29-1 (MRF) or D29-2 (MRFG) - Body ground and other terminals Power switch off 1 MΩ or higher
D29-3 (MSN) or D29-4 (MSNG) - Body ground and other terminals Power switch off 1 MΩ or higher
D29-6 (MCS) or D29-5 (MCSG) - Body ground and other terminals Power switch off 1 MΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Inverter with Converter Assembly)


d.

Reconnect the D29 inverter with converter assembly connector.



OK

7.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)

NG

11.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
7.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
a.
A253109

Check the connection of the generator resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

8.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)

NG

CONNECT SECURELY

8.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A253110

Check the connection of the motor resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

REFER TO REPLACE INVERTER WITH CONVERTER ASSEMBLY PARTS

NG

CONNECT SECURELY

9.CHECK CONNECTOR CONNECTION CONDITION (GENERATOR RESOLVER CONNECTOR)
a.
A253109

Check the connection of the generator resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

10.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)

NG

CONNECT SECURELY

10.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (GENERATOR RESOLVER)
a.
A253109N03
1.583,0.104 1.927,0.344 0.344,0.24 1.625,0.125 1.896,0.313 0.271,0.188 10 true D7

Disconnect the D7 generator resolver connector.


b.
A397757C15
1.448,0.115 1.885,0.344 0.438,0.229 0.885,0.677 1.531,1 true 1.188,1.823 1.625,1.313 true 1.885,1 2.323,0.49 true 2.063,1.042 2.573,0.813 true 2.083,1.292 2.531,1.573 true 1.875,1.313 2.229,1.813 true 0.375,0.115 0.688,0.271 0.313,0.156 10 false *a 1.531,0.146 2.146,0.344 0.615,0.198 10 false D7 2.635,0.719 3.094,0.917 0.458,0.198 10 false GRF 2.573,1.521 3.031,1.719 0.458,0.198 10 false GRFG 2.375,0.375 2.833,0.573 0.458,0.198 10 false GSN 2.073,1.854 2.531,2.052 0.458,0.198 10 false GSNG 0.563,0.563 1.021,0.76 0.458,0.198 10 false GCS 0.958,1.854 1.417,2.052 0.458,0.198 10 false GCSG
*a Component without harness connected
(Generator Resolver (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Switch Condition Specified Condition
D7-1(GRF) - D7-5(GRFG) Power switch off 9.5 to 15.5 Ω
D7-2(GSN) - D7-6(GSNG) Power switch off 15.0 to 27.0 Ω
D7-3(GCS) - D7-7(GCSG) Power switch off 14.0 to 26.0 Ω


Standard Resistance (Check for Short):
Tester Connection Switch Condition Specified Condition
D7-1 (GRF) - Body ground and other terminals (except D7-5 (GRFG)) Power switch off 1 MΩ or higher
D7-5 (GRFG) - Body ground and other terminals (except D7-1 (GRF)) Power switch off 1 MΩ or higher
D7-2 (GSN) - Body ground and other terminals (except D7-6 (GSNG)) Power switch off 1 MΩ or higher
D7-6 (GSNG) - Body ground and other terminals (except D7-2 (GSN)) Power switch off 1 MΩ or higher
D7-3 (GCS) - Body ground and other terminals (except D7-7 (GCSG)) Power switch off 1 MΩ or higher
D7-7 (GCSG) - Body ground and other terminals (except D7-3 (GCS)) Power switch off 1 MΩ or higher


HINT:

The generator resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Connect the D7 generator resolver connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG

11.CHECK CONNECTOR CONNECTION CONDITION (MOTOR RESOLVER CONNECTOR)
a.
A253110

Check the connection of the motor resolver connector.

OK:

The connector is connected securely and there are no contact problems.




OK

12.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)

NG

CONNECT SECURELY

12.INSPECT HYBRID VEHICLE TRANSAXLE ASSEMBLY (MOTOR RESOLVER)
a.
A253110N03
1.448,2.969 1.823,3.188 0.375,0.219 1.479,2.99 1.792,3.177 0.313,0.188 10 true D1

Disconnect the D1 motor resolver connector.


b.
A397815C09
1.448,0.167 1.865,0.417 0.417,0.25 0.406,1.667 1.083,1.177 true 0.948,1.677 1.385,1.208 true 1.458,1.677 1.594,1.198 true 2.854,1.625 2.323,1.188 true 2.458,1.615 2.063,1.208 true 2.031,1.656 1.833,1.198 true 1.906,1.688 2.365,1.885 0.458,0.198 10 false MRF 0.167,1.698 0.625,1.896 0.458,0.198 10 false MRFG 2.74,1.667 3.198,1.865 0.458,0.198 10 false MSN 1.26,1.698 1.719,1.896 0.458,0.198 10 false MSNG 2.323,1.667 2.781,1.865 0.458,0.198 10 false MCS 0.719,1.698 1.177,1.896 0.458,0.198 10 false MCSG 0.396,0.281 0.708,0.438 0.313,0.156 10 false *a 1.594,0.229 2.208,0.427 0.615,0.198 10 false D1
*a Component without harness connected
(Motor Resolver (Hybrid Vehicle Transaxle Assembly))


Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
D1-3 (MRF) - D1-6 (MRFG) Power switch off 9.5 to 15.5 Ω
D1-1 (MSN) - D1-4 (MSNG) Power switch off 15.0 to 27.0 Ω
D1-2 (MCS) - D1-5 (MCSG) Power switch off 14.0 to 26.0 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D1-3 (MRF) - Body ground and other terminals (except D1-6 (MRFG)) Power switch off 1 MΩ or higher
D1-6 (MRFG) - Body ground and other terminals (except D1-3 (MRF)) Power switch off 1 MΩ or higher
D1-1 (MSN) - Body ground and other terminals (except D1-4 (MSNG)) Power switch off 1 MΩ or higher
D1-4 (MSNG) - Body ground and other terminals (except D1-1 (MSN)) Power switch off 1 MΩ or higher
D1-2 (MCS) - Body ground and other terminals (except D1-5 (MCSG)) Power switch off 1 MΩ or higher
D1-5 (MCSG) - Body ground and other terminals (except D1-2 (MCS)) Power switch off 1 MΩ or higher


HINT:

The motor resolver is not available separately. If it requires replacement, replace the hybrid vehicle transaxle assembly.



c.

Connect the D1 motor resolver connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR

NG