Home › Engine / Hybrid System › HYBRID / BATTERY CONTROL › COMBINATION SWITCH
RM2070E _51 Engine / Hybrid System _061906 HYBRID / BATTERY CONTROL _0301585 COMBINATION SWITCH G

HYBRID / BATTERY CONTROL  COMBINATION SWITCH  INSPECTION  


PROCEDURE

Hide 84970 1.INSPECT COMBINATION SWITCH ASSEMBLY

a.

Inspect EV drive mode switch (combination switch assembly)

i.
A253200E20
0.839,0.173 0.991,0.334 0.151,0.161 10 *a 1.384,1.737 1.496,1.898 0.112,0.161 10 S 1.858,1.737 1.967,1.898 0.110,0.161 10 E 1.642,1.225 1.449,1.721 false 1.681,1.029 1.906,1.721 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
7 (S) - 3 (E) EV drive mode switch (combination switch assembly) being pushed and held Below 1 Ω
EV drive mode switch (combination switch assembly) not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(EV drive mode switch (combination switch assembly))

If the result is not as specified, replace the combination switch assembly.



b.

Inspect POWER mode switch (combination switch assembly)

i.
A253200E21
0.693,0.173 0.844,0.334 0.151,0.161 10 *a 1.046,1.737 1.394,1.898 0.348,0.161 10 PWR 1.858,1.737 1.967,1.898 0.110,0.161 10 E 1.459,1.225 1.265,1.721 false 1.681,1.029 1.906,1.721 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
8 (PWR) - 3 (E) POWER mode switch (combination switch assembly) being pushed and held Below 1 Ω
POWER mode switch (combination switch assembly) not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(POWER mode switch (combination switch assembly))

If the result is not as specified, replace the combination switch assembly.



c.

Inspect ECO mode switch (combination switch assembly)

i.
A253200E22
0.635,0.173 0.786,0.334 0.151,0.161 10 *a 2.178,1.737 2.505,1.898 0.327,0.161 10 ECU 1.298,1.737 1.407,1.898 0.110,0.161 10 E 1.996,1.225 2.312,1.721 false 1.642,1.039 1.373,1.731 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (ECU) - 3 (E) ECO mode switch (combination switch assembly) being pushed and held Below 1 Ω
ECO mode switch (combination switch assembly) not pushed 10 kΩ or higher


Text in Illustration
*a Component without harness connected
(ECO mode switch (combination switch assembly))

If the result is not as specified, replace the combination switch assembly.



d.

Inspect illumination

i.

Apply battery voltage between the terminals of the switch, and check the illumination condition of the combination switch assembly.

A251311E02
4.677,1.031 4.958,0.427 4.958,0.427 5.042,0.427 false 4.583,1.146 4.344,1.5 4.344,1.5 4.188,1.5 false 2.406,0.448 1.906,0.448 1.906,0.448 1.906,1.469 false 2.406,0.917 1.906,0.917 false 2.406,1.375 1.906,1.375 false 4.458,0.406 4.635,0.667 0.177,0.26 10 false *a 1.844,1.51 2.021,1.771 0.177,0.26 10 false *b 5.094,0.344 5.365,0.646 0.271,0.302 10 false ILL- 3.896,1.417 4.198,1.719 0.302,0.302 10 false ILL+

OK:
Measurement Condition Specified Condition
Auxiliary battery positive (+) →Terminal 6 (ILL+)
Auxiliary battery negative (-) →Terminal 1 (ILL-)
Illuminates


Text in Illustration
*a Component without harness connected
(Combination Switch Assembly)
*b Combination switch assembly illumination

If the result is not as specified, replace the combination switch assembly.