Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301600 CYLINDER HEAD A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD  REPLACEMENT  


PROCEDURE

Hide 11122 1.REPLACE INTAKE VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A150967E01
0.142,0.058 0.448,0.216 0.306,0.159 10 SST 1.342,0.635 0.5,0.164 0.5,0.164 1.231,1.197 false

Using SST and a hammer, tap out the guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A352267

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select New Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore to a diameter of 10.335 to 10.356 mm (0.407 to 0.408 in.) in order to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head on wooden blocks.


g.
A150969E02
0.264,0.138 0.566,0.289 0.302,0.151 10 SST 1.345,0.626 0.655,0.223 0.655,0.223 1.231,1.204 false 3.178,0.665 3.346,0.817 0.168,0.152 10 *a

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

Text in Illustration
*a Height

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

9.9 to 10.3 mm (0.390 to 0.406 in.)



h.
A150971

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.025 to 0.060 mm (0.000984 to 0.00236 in.)



Hide 11126 2.REPLACE EXHAUST VALVE GUIDE BUSH

a.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


b.

Place the cylinder head on wooden blocks.


c.
A150968E01
1.522,1.759 1.843,1.908 0.320,0.149 10 SST 2.063,0.83 1.751,1.749 1.751,1.749 2.222,1.192 false

Using SST and a hammer, tap out the guide bush.

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)


d.
A152650

Using a caliper gauge, measure the bush bore diameter of the cylinder head.

Standard cylinder bore diameter:

10.285 to 10.306 mm (0.405 to 0.406 in.)


Select New Guide Bush:
Bush Size Bush Diameter
STD 10.333 to 10.344 mm (0.4068 to 0.4072 in.)
O/S 0.05 10.383 to 10.394 mm (0.4088 to 0.4092 in.)


If the bush bore diameter of the cylinder head is more than 10.306 mm (0.406 in.), machine the bush bore to a diameter of 10.335 to 10.356 mm (0.407 to 0.408 in.) in order to install an O/S 0.05 valve guide bush. If the bush bore diameter of the cylinder head is more than 10.356 mm (0.408 in.), replace the cylinder head.


e.

Heat the cylinder head to 80 to 100°C (176 to 212°F).


f.

Place the cylinder head on wooden blocks.


g.
A150970E02
0.943,0.706 1.104,0.859 0.161,0.153 10 *a 1.434,1.627 1.751,1.799 0.316,0.172 10 SST 1.934,0.458 1.665,1.577 1.665,1.577 2.199,1.145 false

Using SST and a hammer, tap in a new guide bush to the specified protrusion height.

Text in Illustration
*a Height

SST
09201-10000  (09201-01050)
09950-70010  (09951-07100)

Standard protrusion height:

11.15 to 11.55 mm (0.439 to 0.455 in.)



h.
A150972

Using a sharp 5.5 mm reamer, ream the guide bush to obtain the standard clearance between the guide bush and valve stem.

Standard oil clearance:

0.030 to 0.065 mm (0.00118 to 0.00256 in.)



Hide 11155A 3.REPLACE RING PIN

NOTICE:

It is not necessary to remove a ring pin unless it is being replaced.


a.

Remove the ring pins.


b.
A150959E08
0.791,2.431 0.953,2.580 0.162,0.149 10 *a 1.299,3.004 1.461,3.157 0.162,0.153 10 *b 1.537,3.549 1.703,3.712 0.167,0.164 10 *c

Using a plastic-faced hammer, tap in a new ring pin to the specified protrusion height.

Text in Illustration
*a Width
*b Height
*c Protrusion Height

Standard Ring Pin:
Item Height Width Protrusion
Ring pin 11.7 to 12.3 mm (0.461 to 0.484 in.) 12.0 mm (0.472 in.) 6.5 to 7.5 mm (0.256 to 0.295 in.)