Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER HEAD
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301600 CYLINDER HEAD A

2ZR-FXE ENGINE MECHANICAL  CYLINDER HEAD  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL SPARK PLUG TUBE

NOTICE:

When using a new cylinder head, the spark plug tubes must be replaced.


a.
U124846E02
2.271,0.146 2.156,0.146 2.156,0.146 2.063,0.583 false 2.313,0.063 3.219,0.323 0.906,0.26 10 false 1.0 to 3.0 mm 0.271,1.51 1.542,1.885 1.271,0.375 10 false 1.0 to 13.0 mm (0.0394 to 0.512 in.)

Apply adhesive onto the shaded area of a new spark plug tube.

Adhesive:

Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent


Standard application width:

1.0 to 3.0 mm (0.0394 to 0.118 in.)


NOTICE:
·

Install the spark plug tube within 3 minutes of applying adhesive.

·

Be careful not to deform the spark plug tube.

·

Be careful not to expose the seal to coolant for at least 1 hour after installing the tube.




b.
A205906E04
0.68,2.437 0.851,2.606 0.171,0.169 10 *a 2.407,2.942 3.068,3.088 0.661,0.147 10 122 mm

Using a wooden block and a hammer, tap in the spark plug tube to the specified protrusion height.

Text in Illustration
*a Cylinder Head Casting Surface

Standard protrusion height:

122 mm (4.80 in.)


NOTICE:

To avoid tapping in the spark plug tube too far, measure the protrusion height while tapping it.



Hide 2.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or its threads are damaged, replace it.


a.

Using an E8 "TORX" socket, install the stud bolts.

U110389E01
0.34,0.125 0.589,0.340 0.249,0.215 10 *a 4.075,0.125 4.293,0.358 0.218,0.233 10 *b 0.953,0.706 1.127,0.881 0.174,0.175 10 A 2.269,0.71 2.443,0.866 0.174,0.156 10 A 1.214,2.221 1.388,2.414 0.174,0.193 10 A 4.649,2.365 4.824,2.559 0.174,0.193 10 B 4.288,1.578 4.463,1.771 0.174,0.193 10 B 5.453,1.637 5.627,1.830 0.174,0.193 10 B 6.581,1.58 6.755,1.774 0.174,0.193 10 B 6.088,0.739 6.219,0.892 0.130,0.153 10 B 4.812,0.72 4.986,0.914 0.174,0.193 10 B 1.978,2.122 3.101,2.300 1.123,0.177 10 24 mm (0.945 in.) 1.927,3.426 3.083,3.607 1.156,0.181 10 13 mm (0.512 in.) 2.366,2.743 3.717,3.031 1.351,0.288 10 49.5 mm (1.95 in.) 5.354,2.218 6.478,2.378 1.124,0.159 10 20 mm (0.787 in.) 5.869,2.82 6.948,2.987 1.079,0.167 10 42 mm (1.65 in.) 1.931,2.192 1.868,2.192 1.868,2.192 1.598,2.677 false 1.892,3.5 1.829,3.5 1.829,3.5 1.598,3.192 false 5.353,3.44 6.509,3.621 1.156,0.181 10 13 mm (0.512 in.) 5.318,3.514 5.255,3.514 5.255,3.514 5.024,3.206 false 5.315,2.299 5.255,2.299 5.255,2.299 5.023,2.842 false

Text in Illustration
*a Intake Side: *b Exhaust Side:

Torque:
9.5 N*m (97 kgf*cm, 84 in.*lbf)


Hide 11117B 3.INSTALL NO. 2 STRAIGHT SCREW PLUG

NOTICE:

If water leaks from the straight screw plug or the plug is corroded, replace it.


a.
A150950

Using a 10 mm straight hexagon wrench, install 3 new gaskets and the 3 straight screw plugs.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 13734 4.INSTALL VALVE SPRING SEAT

a.

Install the valve spring seats to the cylinder head.


Hide 5.INSTALL VALVE STEM OIL SEAL

a.
A146313E08
0.096,0.075 0.266,0.250 0.170,0.174 10 *a 1.884,0.075 2.100,0.250 0.216,0.174 10 *b 1.273,0.726 1.437,0.873 0.164,0.147 10 *c 0.963,1.058 1.252,0.817 false 3.13,0.676 3.293,0.823 0.164,0.147 10 *d 2.819,1.008 3.108,0.768 false

Apply a light coat of engine oil to a new oil seal.

Text in Illustration
*a Intake Side:
*b Exhaust Side:
*c Gray
*d Black

NOTICE:

Pay close attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal to the exhaust side or installing the exhaust oil seal to the intake side can cause installation problems later.


HINT:

The intake valve oil seal is gray and the exhaust valve oil seal is black.



b.
A150956E02
0.095,0.812 0.418,0.977 0.323,0.165 10 SST 0.581,1.279 0.749,1.445 0.168,0.166 10 *a 1.918,1.279 2.083,1.434 0.165,0.154 10 *b 0.456,0.91 0.588,0.91 0.588,0.91 1.054,0.695 false

Using SST, push on the oil seal.

Text in Illustration
*a CORRECT
*b INCORRECT

SST
09201-41020  

NOTICE:

Failure to use SST will cause the seal to be damaged or improperly seated.



Hide 13711 6.INSTALL INTAKE VALVE

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.


A314486E01
1.71,0.062 1.945,0.251 0.235,0.189 12 *B 1.785,0.624 2.020,0.813 0.235,0.189 10 *1 1.981,0.651 2.088,0.484 false 1.8,0.851 2.035,1.040 0.235,0.189 10 *2 1.997,0.937 2.24,0.937 false 1.862,1.494 2.097,1.683 0.235,0.189 10 *3 2.058,1.579 2.302,1.579 false 1.945,2.739 2.180,2.928 0.235,0.189 10 *4 2.142,2.824 2.385,2.824 false 1.678,0.047 3.156,3.158 1.479,3.111 0.094,0.062 0.329,0.251 0.235,0.189 12 *A 0.17,0.624 0.405,0.813 0.235,0.189 10 *1 0.366,0.651 0.472,0.484 false 0.184,0.851 0.419,1.040 0.235,0.189 10 *2 0.381,0.937 0.625,0.937 false 0.263,1.494 0.498,1.683 0.235,0.189 10 *3 0.46,1.579 0.704,1.579 false 0.347,2.739 0.582,2.928 0.235,0.189 10 *4 0.543,2.824 0.787,2.824 false 0.062,0.047 1.541,3.158 1.479,3.111

Text in Illustration
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Compression Spring
*4 Valve Lash Adjuster Assembly

Type Compression Spring Shape
A Straight
B Tapered

a.

Type A:

i.

Place the cylinder head on wooden blocks.


ii.
A378787E06
2.292,1.646 3.313,2 1.021,0.354 10 false 30 mm or more

Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.


iii.

Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to the original locations.



iv.
A150946E02
1.413,0.22 1.745,0.381 0.333,0.161 10 SST 1.803,0.314 1.897,0.314 1.897,0.314 1.948,0.563 false

Using SST, compress the spring and install the valve retainer locks.

SST
09202-70020  (09202-00010)


v.
A150974

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the retainer.





b.

Type B:

i.

Place the cylinder head on wooden blocks.


ii.
A378787E06
2.292,1.646 3.313,2 1.021,0.354 10 false 30 mm or more

Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.


iii.
A314495E01
1.664,0.121 1.895,0.304 0.231,0.183 10 *a 1.249,0.667 1.493,0.667 false 1.027,0.573 1.258,0.756 0.231,0.183 10 *2 1.318,1.326 1.562,1.326 false 1.096,1.232 1.327,1.415 0.231,0.183 10 *1 0.944,1.553 1.147,1.87 false 0.722,1.459 0.953,1.642 0.231,0.183 10 *3

Install the valve, compression spring and spring retainer to the cylinder head.

Text in Illustration
*1 Compression Spring
*2 Valve Spring Retainer
*3 Cylinder Head
*a Upper Side

NOTICE:
·

Install the compression spring with its taper side facing upward (towards the valve spring retainer).

·

Install the same parts in the same combination to the original locations.




iv.
A331963E01
1.166,0.118 1.747,0.366 0.581,0.247 10 SST 1.532,0.194 1.709,0.194 false 1.709,0.194 1.894,0.571 false

Using SST, compress the spring and install the valve retainer locks.

SST
09202-70020  
09202-00020  


v.
A331965

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the retainer.





Hide 13715 7.INSTALL EXHAUST VALVE

HINT:

Type A and Type B can be distinguished by the shape of the compression spring.


A314486E01
1.71,0.062 1.945,0.251 0.235,0.189 12 *B 1.785,0.624 2.020,0.813 0.235,0.189 10 *1 1.981,0.651 2.088,0.484 false 1.8,0.851 2.035,1.040 0.235,0.189 10 *2 1.997,0.937 2.24,0.937 false 1.862,1.494 2.097,1.683 0.235,0.189 10 *3 2.058,1.579 2.302,1.579 false 1.945,2.739 2.180,2.928 0.235,0.189 10 *4 2.142,2.824 2.385,2.824 false 1.678,0.047 3.156,3.158 1.479,3.111 0.094,0.062 0.329,0.251 0.235,0.189 12 *A 0.17,0.624 0.405,0.813 0.235,0.189 10 *1 0.366,0.651 0.472,0.484 false 0.184,0.851 0.419,1.040 0.235,0.189 10 *2 0.381,0.937 0.625,0.937 false 0.263,1.494 0.498,1.683 0.235,0.189 10 *3 0.46,1.579 0.704,1.579 false 0.347,2.739 0.582,2.928 0.235,0.189 10 *4 0.543,2.824 0.787,2.824 false 0.062,0.047 1.541,3.158 1.479,3.111

Text in Illustration
*A Type A
*B Type B
*1 No. 1 Valve Rocker Arm Sub-assembly
*2 Valve Spring Retainer
*3 Compression Spring
*4 Valve Lash Adjuster Assembly

Type Compression Spring Shape
A Straight
B Tapered

a.

Type A:

i.

Place the cylinder head on wooden blocks.


ii.
A378788E05
2.26,1.719 3.26,2.052 1,0.333 10 false 30 mm or more

Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.


iii.

Install the valve, compression spring and spring retainer to the cylinder head.

NOTICE:

Install the same parts in the same combination to the original locations.



iv.
A150947E02
0.114,0.191 0.447,0.352 0.333,0.161 10 SST 0.505,0.284 0.598,0.284 0.598,0.284 0.649,0.533 false

Using SST, compress the spring and install the valve retainer locks.

SST
09202-70020  (09202-00010)


v.
A150973

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the retainer.





b.

Type B:

i.

Place the cylinder head on wooden blocks.


ii.
A378788E05
2.26,1.719 3.26,2.052 1,0.333 10 false 30 mm or more

Apply engine oil to each valve over an area 30 mm (1.18 in.) or more from its tip as shown in the illustration.


iii.
A314495E01
1.664,0.121 1.895,0.304 0.231,0.183 10 *a 1.249,0.667 1.493,0.667 false 1.027,0.573 1.258,0.756 0.231,0.183 10 *2 1.318,1.326 1.562,1.326 false 1.096,1.232 1.327,1.415 0.231,0.183 10 *1 0.944,1.553 1.147,1.87 false 0.722,1.459 0.953,1.642 0.231,0.183 10 *3

Install the valve, compression spring and spring retainer to the cylinder head.

Text in Illustration
*1 Compression Spring
*2 Valve Spring Retainer
*3 Cylinder Head
*a Upper Side

NOTICE:
·

Install the compression spring with its taper side facing upward (towards the valve spring retainer).

·

Install the same parts in the same combination to the original locations.




iv.
A331964E01
0.231,1.822 0.748,2.006 0.517,0.184 10 SST 0.474,1.587 0.391,1.788 false

Using SST, compress the spring and install the valve retainer locks.

SST
09202-70020  
09202-00020  


v.
A331966

Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

NOTICE:
·

Be careful not to damage the valve stem tip.

·

Be careful not to damage the retainer.