Home › Engine / Hybrid System › 2ZR-FXE (ENGINE MECHANICAL) › CYLINDER BLOCK
RM2070E _51 Engine / Hybrid System _061907 2ZR-FXE ENGINE MECHANICAL _0301601 CYLINDER BLOCK A

2ZR-FXE ENGINE MECHANICAL  CYLINDER BLOCK  REASSEMBLY  


PROCEDURE

Hide 1.INSTALL STUD BOLT

NOTICE:

If a stud bolt is deformed or the threads are damaged, replace it.


HINT:

There are 2 installation types for the No. 1 ventilation case.

This procedure is for type A.


a.
U110392E01
0.14,2.81 1.328,2.970 1.188,0.160 10 16 mm (0.630 in.) 0.208,4.248 1.304,4.408 1.096,0.160 10 9 mm (0.354 in.) 2.596,3.498 3.274,3.866 0.678,0.368 10 27 mm (1.063 in.) 2.069,3.598 1.723,2.909 1.723,2.909 1.566,2.909 false 1.543,4.333 1.735,4.333 1.735,4.333 2.069,3.995 false 0.189,0.059 0.393,0.252 0.204,0.193 10 *a

Using an E6 "TORX" socket, install the stud bolts as shown in the illustration.

Text in Illustration
*a LH Side

Torque:
5.0 N*m (51 kgf*cm, 44 in.*lbf)


Hide 15708 2.INSTALL NO. 1 OIL NOZZLE SUB-ASSEMBLY

a.
A151001

Using a 5 mm socket hexagon wrench, install the 4 oil nozzles with the 4 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 13101 3.INSTALL PISTON

a.
A151020E02
2.065,1.671 2.269,1.836 0.205,0.165 10 *1 1.126,1.221 2.15,1.648 2.15,1.648 2.15,1.23 false

Using a screwdriver, install a new snap ring at one end of the piston pin hole.

Text in Illustration
*1 Service Hole

HINT:

Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



b.

Gradually heat the piston to approximately 80 to 90°C (176 to 194°F).


c.
A151021E18
1.354,0.177 1.24,0.177 1.24,0.177 0.979,0.646 false 1.417,2.375 2.25,3.115 2.25,3.115 2.802,2.771 false 2.854,2.042 2.25,3.115 false 1.385,0.094 1.594,0.26 0.208,0.167 10 false *a 2.135,3.135 2.344,3.302 0.208,0.167 10 false *a

Align the front marks of the piston and connecting rod, insert the connecting rod into the piston, and then push in the piston pin with your thumb until the pin comes into contact with the snap ring.

Text in Illustration
*a Front Mark

HINT:

The piston and pin are a matched set.



d.

Using a screwdriver, install a new snap ring on the other end of the piston pin hole.

HINT:

Make sure that the end gap of the snap ring is not aligned with the pin hole cutout portion of the piston.



e.
A152651

Check the fitting condition between the piston and piston pin by trying to move the piston back and forth on the piston pin.


Hide 13011 4.INSTALL PISTON RING SET

a.

for 2-piece Type:

i.
A146333E19
1.458,1.813 1.458,1.542 false 2.125,0.271 1.938,0.271 1.938,0.271 1.802,0.479 false 0.865,0.24 0.979,0.24 0.979,0.24 1.333,0.552 false 1.417,2.906 1.479,3.021 1.479,3.021 1.542,2.906 false 0.677,0.146 0.865,0.323 0.188,0.177 10 false *1 2.167,0.177 2.354,0.354 0.188,0.177 10 false *2 1.375,1.833 1.563,2.01 0.188,0.177 10 false *3 1.385,3.042 1.573,3.219 0.188,0.177 10 false *4

Install the oil ring expander and oil ring by hand.

Text in Illustration
*1 Oil Ring Expander
*2 Oil Ring
*3 Coil Joint
*4 Oil Ring End

NOTICE:
·

Install the expander and oil ring so that their ring ends are at opposite sides.

·

Securely install the expander to the inner groove of the oil ring.





b.

for 3-piece Type:

i.
A318878E07
0.74,1.083 1.063,1.083 false 2.281,0.604 2.542,0.354 false 2.313,1.563 2.583,1.792 false 2.573,0.271 2.885,0.469 0.313,0.198 10 false *1 2.615,1.729 2.927,1.927 0.313,0.198 10 false *3 0.563,1 0.875,1.198 0.313,0.198 10 false *2

Install the oil ring expander and 2 side rails by hand.

Text in Illustration
*1 Upper Side Rail
*2 Oil Ring Expander
*3 Lower Side Rail

NOTICE:

When installing the upper side rail and lower side rail, the ends of the oil ring expander may overlap. If it occurs, the upper side rail or lower side rail may move out of its groove.



ii.

Check that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

A321517E11
1.604,0.698 3.854,1.042 2.25,0.344 10 false *a 4.188,1.823 5.427,2.156 1.24,0.333 10 false *b 3.542,0.875 5.531,1.146 1.99,0.271 10 false *c 3.531,2.302 5.521,2.573 1.99,0.271 10 false *d

Text in Illustration
*a Press around the circumference *b Ring End
*c Correct *d Incorrect (Ends of the oil ring expander are overlapping)

NOTICE:
·

After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.

·

If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.

·

If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.





c.

Using a piston ring expander, install the 2 compression rings so that the paint marks are positioned as shown in the illustration.

A398186C02
1.677,0.594 1.865,0.438 1.865,0.438 2.073,0.438 false 3.875,1.031 4.333,1.219 4.333,1.219 4.49,1.219 false 3.958,1.573 4.365,1.573 false 4.104,2.313 3.917,2.313 3.917,2.313 3.698,1.625 false 5.104,2.125 5.104,1.906 false 3.708,1.01 4.146,0.625 4.146,0.625 4.385,0.625 false 6.458,2.125 6.458,1.906 false 2.146,0.385 2.458,0.583 0.313,0.198 10 false *3 4.438,0.542 4.75,0.74 0.313,0.198 10 false *a 4.521,1.135 4.833,1.333 0.313,0.198 10 false *c 4.156,2.229 4.469,2.427 0.313,0.198 10 false *b 2.719,1.271 3.031,1.469 0.313,0.198 10 false *1 2.802,1.927 3.115,2.125 0.313,0.198 10 false *2 6.396,2.188 6.708,2.385 0.313,0.198 10 false *2 5.021,2.188 5.333,2.385 0.313,0.198 10 false *1 4.396,1.5 4.708,1.698 0.313,0.198 10 false *c
*1 No. 1 Compression Ring *2 No. 2 Compression Ring
*3 Piston Ring Expander *a Code Mark (1R)
*b Code Mark (2R) *c Paint Mark
V100135

Upward - -


Piston Ring Mark:
Item Type Paint Mark
No. 1 Compression Ring Type A Pink
Type B Orange


NOTICE:
·

Install the No. 1 compression ring with the code mark (1R) facing upward.

·

Install the No. 2 compression ring with the code mark (2R) facing upward.

·

Paint marks can only be checked on new piston rings. When reusing piston rings, check each piston ring profile in order to install them into the correct positions.




d.

for 2-piece Type:

i.
U124826E01
2.664,1.242 2.952,1.416 0.287,0.173 10 45° 0.727,2.273 0.890,2.431 0.163,0.158 10 *1 2.316,0.652 2.480,0.799 0.164,0.147 10 *2 1.145,2.297 0.903,2.343 false 2.199,1.243 2.331,0.829 false

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring and Oil Ring
*2 No. 2 Compression Ring and Oil Ring Expander
V100135

Engine Front



e.

for 3-piece Type:

i.
A331707E06
0.958,1.104 1.198,1.302 0.24,0.198 10 false *4 2.333,0.927 2.573,1.125 0.24,0.198 10 false *2 2.563,1.302 2.917,1.5 0.354,0.198 10 false 45° 2.24,2.344 2.479,2.542 0.24,0.198 10 false *3 0.948,2.354 1.188,2.552 0.24,0.198 10 false *1 0.667,1.708 0.906,1.906 0.24,0.198 10 false *a

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 compression ring and Oil Ring Expander
*2 No. 2 compression ring
*3 Upper Side Rail
*4 Lower Side Rail
*a Engine Front



Hide 11711 5.INSTALL CRANKSHAFT BEARING

a.
A151015E04
0.421,0.98 0.633,1.168 0.212,0.188 10 *1 0.372,1.068 0.131,1.068 0.131,1.068 0.536,2.362 false 0.562,2.05 0.693,2.213 0.131,0.164 10 A

Install the upper bearing (except No. 3 journal).

Text in Illustration
*1 Vernier Caliper

i.

Install the upper bearing to the cylinder block.

HINT:

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.



ii.

Using a vernier caliper, measure the distance between the cylinder block edge and the upper bearing edge.

Standard dimension (A):

0.5 to 1.0 mm (0.0197 to 0.0394 in.)


NOTICE:

Do not apply engine oil to the bearings or the contact surfaces.




b.
A162987E04
0.803,1.996 1.047,2.229 0.243,0.232 10 A 1.988,2.01 2.187,2.193 0.199,0.183 10 B 0.651,1.009 0.884,1.166 0.233,0.157 10 *1 0.682,2.449 0.352,1.09 0.352,1.09 0.601,1.09 false

Install the upper bearing (for No. 3 journal).

Text in Illustration
*1 Vernier Caliper

i.

Install the upper bearing to the cylinder block.

HINT:

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.



ii.

Using a vernier caliper, measure the distance between the cylinder block edge and the upper bearing edge.

Standard dimension (A - B):

0.7 mm (0.0276 in.) or less


NOTICE:

Do not apply engine oil to the bearing or the contact surfaces.




c.

Install the lower bearing.

i.

Install the upper bearing to the cylinder block.

HINT:

Both sides of the oil groove in the cylinder block should be visible through the oil feed holes in the bearing. The amount visible on each side of the holes should be equal.



ii.
A151016E06
0.789,1.985 0.957,2.144 0.168,0.159 10 *a 0.725,2.911 0.860,3.073 0.135,0.162 10 A 2.054,2.911 2.190,3.073 0.135,0.162 10 B 2.567,2.082 2.743,2.242 0.176,0.160 10 *1 2.526,2.174 2.406,2.174 2.406,2.174 2.198,2.533 false

Using a vernier caliper, measure the distance between the bearing cap edge and the lower bearing edge.

Text in Illustration
*1 Vernier Caliper
*a Mark 1, 2, 3, 4 or 5

Standard dimension (A - B):

0.7 mm (0.0276 in.) or less


NOTICE:

Do not apply engine oil to the bearings or the contact surfaces.




Hide 11791 6.INSTALL UPPER CRANKSHAFT THRUST WASHER

a.
A150982E12
1.323,1.302 1.448,1.813 1.448,1.813 1.552,1.479 false 1.344,1.813 1.51,1.969 0.167,0.156 10 true *1

Install the 2 thrust washers to the No. 3 journal position of the cylinder block with the oil grooves facing outward.

Text in Illustration
*1 Oil Groove


b.

Apply engine oil to the crankshaft thrust washer.


Hide 13411 7.INSTALL CRANKSHAFT

a.

Apply engine oil to the upper bearings and install the crankshaft to the cylinder block.


b.

Apply engine oil to the lower bearings.


c.
U110390E01
0.56,2.62 0.56,2.908 false 0.56,2.816 3.206,2.816 3.206,2.816 3.206,2.624 false 2.551,2.62 2.551,2.816 false 1.88,2.62 1.88,2.816 false 1.23,2.62 1.23,2.816 false 0.467,2.923 0.630,3.080 0.163,0.157 10 *a

Examine the number marks and install the bearing caps to the cylinder block.

Text in Illustration
*a Number Mark
V100135

Engine Front


d.

Apply a light coat of engine oil to the threads and under the heads of the bearing cap bolts.


e.
A205910

Temporarily install the 10 crankshaft bearing cap bolts.


f.
A205917E02
1.972,2.359 2.157,2.515 0.185,0.156 10 *a

Push on the crankshaft bearing caps with your hand until the clearance between the crankshaft bearing caps and cylinder block is less than 5 mm (0.197 in.).

Text in Illustration
*a Less than 5 mm


g.
A151024

Using a plastic-faced hammer, lightly tap the bearing cap to ensure a proper fit.


h.

Install the crankshaft bearing cap bolts.

NOTICE:

The crankshaft bearing cap bolts are tightened in 2 progressive steps.



i.

Step 1:

i.
A205910E10
0.479,0.427 0.583,0.583 0.104,0.156 10 false 8 1.042,0.354 1.177,0.5 0.135,0.146 10 true 4 1.719,0.365 1.896,0.552 0.177,0.188 10 true 1 2.344,0.385 2.448,0.552 0.104,0.167 10 true 6 2.938,0.396 3.135,0.552 0.198,0.156 10 false 10 2.969,1.74 3.083,1.906 0.115,0.167 10 false 9 2.406,1.76 2.531,1.917 0.125,0.156 10 true 5 1.719,1.792 1.833,1.958 0.115,0.167 10 false 2 1.021,1.771 1.188,1.938 0.167,0.167 10 true 3 0.458,1.729 0.563,1.896 0.104,0.167 10 false 7

Install and uniformly tighten the 10 crankshaft bearing cap bolts in the sequence shown in the illustration.

Torque:
40 N*m (408 kgf*cm, 30 ft.*lbf)



j.

Step 2:

i.
A379393E02
2.219,0.552 2.573,0.365 true 1.344,0.302 1.771,0.542 0.427,0.24 10 false 90° 2.594,0.24 3.021,0.479 0.427,0.24 10 false *a

Mark the front of the bearing cap bolts with paint.

Text in Illustration
*a Paint Mark
V100135

Engine Front


ii.

Tighten the bearing cap bolts 90° in the sequence shown in step 1.



k.

Check that the paint marks are now at a 90° angle to the front.


l.

Check that the crankshaft turns smoothly.


m.

Check the crankshaft thrust clearance (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY).


Hide 13041 8.INSTALL CONNECTING ROD BEARING

a.

Install the connecting rod bearings to the connecting rods and connecting rod caps.


b.
A151017E05
1.96,2.491 2.102,2.651 0.142,0.160 10 A 2.957,2.491 3.098,2.651 0.142,0.160 10 B 0.329,1.601 0.563,1.775 0.234,0.174 10 *1 0.272,1.68 0.122,1.68 0.122,1.68 0.342,2.694 false

Using a vernier caliper, measure the distance between the edges of the connecting rods and connecting cap bearings, and the connecting rod caps and the connecting rod bearings.

Text in Illustration
*1 Vernier Caliper

Standard dimension A - B or B - A:

0 to 0.7 mm (0 to 0.0276 in.)


NOTICE:

Do not apply engine oil to the bearings or the contact surfaces.



Hide 9.INSTALL PISTON SUB-ASSEMBLY WITH CONNECTING ROD

a.

Apply engine oil to the cylinder walls, pistons, and the surfaces of the connecting rod bearings.


b.

for 2-piece Type:

i.
U124826E01
2.664,1.242 2.952,1.416 0.287,0.173 10 45° 0.727,2.273 0.890,2.431 0.163,0.158 10 *1 2.316,0.652 2.480,0.799 0.164,0.147 10 *2 1.145,2.297 0.903,2.343 false 2.199,1.243 2.331,0.829 false

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 Compression Ring and Oil Ring
*2 No. 2 Compression Ring and Oil Ring Expander
V100135

Engine Front

NOTICE:

Do not align the ring ends.




c.

for 3-piece Type:

i.
A331707E06
0.958,1.104 1.198,1.302 0.24,0.198 10 false *4 2.333,0.927 2.573,1.125 0.24,0.198 10 false *2 2.563,1.302 2.917,1.5 0.354,0.198 10 false 45° 2.24,2.344 2.479,2.542 0.24,0.198 10 false *3 0.948,2.354 1.188,2.552 0.24,0.198 10 false *1 0.667,1.708 0.906,1.906 0.24,0.198 10 false *a

Position the piston rings so that the ring ends are as shown in the illustration.

Text in Illustration
*1 No. 1 compression ring and Oil Ring Expander
*2 No. 2 compression ring
*3 Upper Side Rail
*4 Lower Side Rail
*a Engine Front


ii.

Confirm that the ends of the oil ring expander are not overlapping and that the upper side rail and lower side rail are securely installed into the groove.

A321517E11
1.604,0.698 3.854,1.042 2.25,0.344 10 false *a 4.188,1.823 5.427,2.156 1.24,0.333 10 false *b 3.542,0.875 5.531,1.146 1.99,0.271 10 false *c 3.531,2.302 5.521,2.573 1.99,0.271 10 false *d

Text in Illustration
*a Press around the circumference *b Ring End
*c Correct *d Incorrect (Ends of the oil ring expander are overlapping)

NOTICE:
·

After installing the oil ring expander, upper side rail and lower side rail, press around the circumference with a finger to check that they are securely installed into the groove.

·

If the oil ring expander is not securely installed into the groove, check that the ends of the oil ring expander are not overlapping.

·

If the ends of the oil ring expander are overlapping, remove the upper side rail and lower side rail and realign the oil ring expander using a screwdriver.





d.
A151019E05
1.264,3.807 1.125,2.664 1.125,2.664 2.239,2.864 false 2.487,4.069 1.128,2.666 false 0.879,2.585 1.053,2.740 0.173,0.156 10 *a

Using a piston ring compressor, push the correctly numbered piston and connecting rod assembly into the cylinder with the front mark of the piston facing forward.

Text in Illustration
*a Front Mark

NOTICE:
·

When inserting the piston with connecting rod, do not allow it to make contact with the oil nozzle.

·

Match the numbered connecting rod cap with the connecting rod.




e.
A205918E06
0.453,0.318 0.626,0.456 0.173,0.139 10 *a 0.646,0.407 0.802,0.407 0.802,0.407 1.418,0.722 false

Check that the front mark of the connecting rod cap is facing in the correct direction.

Text in Illustration
*a Front Mark


f.

Apply a light coat of engine oil to the threads and under the heads of the connecting rod cap bolts.


g.

Install the connecting rod cap bolts.

NOTICE:

The connecting rod cap bolts should be tightened in 2 progressive steps.



h.

Step 1:

i.
A205915E06
0.771,0.396 0.906,0.396 0.906,0.396 1.177,0.552 false 0.448,0.313 0.823,0.5 0.375,0.188 10 false SST

Using SST, install and alternately tighten the bolts of the connecting rod cap in several steps.

SST
09205-16011  

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)



i.

Step 2:

i.
A101478E14
1.08,0.326 1.435,0.507 0.355,0.181 10 90° 2.418,0.376 2.595,0.557 0.177,0.181 10 *a 2.088,0.736 2.379,0.528 false

Mark the front of the connecting rod cap bolts with paint.

Text in Illustration
*a Paint Mark
V100136

Engine Front


ii.

Tighten the cap bolts 90° as shown in the illustration.



j.

Check that the crankshaft turns smoothly.


k.

Check the connecting rod thrust clearance (See page Engine / Hybrid System>2ZR-FXE (ENGINE MECHANICAL)>CYLINDER BLOCK>DISASSEMBLY).


Hide 12211 10.INSTALL NO. 1 VENTILATION CASE

HINT:

There are 2 installation types for the No. 1 ventilation case.

Depending on the installation type, the number of bolts, nuts and stud bolts used will vary.


a.
U110394E01
2.75,0.927 2.874,1.083 0.124,0.156 10 A 1.946,0.927 2.071,1.083 0.124,0.156 10 A 2.248,3.776 2.420,3.926 0.172,0.150 10 *b 0.285,2.356 0.458,2.505 0.173,0.149 10 *a 0.788,1.618 0.391,2.186 0.391,2.186 0.391,2.358 false 1.552,3.693 1.902,3.849 0.350,0.156 10 A - A 1.377,2.634 1.872,2.780 0.496,0.147 10 3.0 mm 2.14,3.069 3.037,3.215 0.897,0.147 10 2.0 to 3.0 mm

Apply seal packing in a continuous line as shown in the illustration.

Text in Illustration
*a Seal Packing
*b Seal Packing Diameter

Seal packing:

Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent


Application Specification:
Seal Packing Diameter Distance from inside edge of cover to center of seal packing
2.0 to 3.0 mm (0.0787 to 0.118 in.) 3.0 mm (0.118 in.)


NOTICE:
·

Remove any oil from the contact surfaces.

·

Install the ventilation case within 3 minutes and tighten the bolts and nuts within 15 minutes of applying seal packing.

·

Do not start the engine for at least 2 hours after installation.




b.

Type A:

i.
A150902

Install the ventilation case with the 6 bolts and 2 nuts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)



c.

Type B:

i.
A221752

Install the ventilation case with the 8 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)