Home › Engine / Hybrid System › 2ZR-FXE (FUEL) › FUEL SYSTEM › 2012.03–2013.08
RM2070E _51 Engine / Hybrid System _061908 2ZR-FXE FUEL _0301602 FUEL SYSTEM G

2ZR-FXE FUEL  FUEL SYSTEM  ON-VEHICLE INSPECTION  


PROCEDURE

Hide 1.CHECK FUEL PUMP OPERATION AND INSPECT FOR FUEL LEAK

a.

Check fuel pump operation.

i.

Connect the GTS to the DLC3.


ii.

Turn the power switch on (IG).

NOTICE:

Do not start the engine.



iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


v.

Check for pressure in the fuel inlet tube from the fuel line. Check that sounds of fuel flowing from the fuel tank can be heard. If no sounds can be heard, check the integration relay, fuel pump, ECM and wiring connectors.



b.

Inspect for fuel leaks.

i.

Check that there are no fuel leaks after performing maintenance anywhere on the fuel system. If there are fuel leaks, repair or replace parts as necessary.



c.

Turn the power switch off.


d.

Disconnect the GTS from the DLC3.


Hide 2.CHECK FUEL PRESSURE

a.

Discharge fuel system pressure (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>PRECAUTION).


b.

Using a voltmeter, measure the auxiliary battery voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
Positive terminal - Negative terminal Power switch off 11 to 14 V



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



d.

Disconnect the fuel hose from the fuel main tube (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>PRECAUTION).


e.
A264978E10
0.854,0.49 0.604,0.49 false 1.51,0.771 1.51,1.073 false 1.115,1 1.115,1.188 false 2.885,0.396 2.656,0.167 2.656,0.167 2.531,0.167 false 2.01,1.635 2.313,1.344 2.313,1.344 2.385,1.344 false 0.792,2.375 0.792,2.573 false 2.219,2.354 2.219,2.5 false 3.25,2.635 3.01,2.635 false 1.594,3.344 1.844,3.083 1.844,3.083 1.927,3.083 false 2.333,3.594 2.583,3.844 2.583,3.844 2.656,3.844 false 1.375,3.948 1.51,4.083 1.51,4.083 1.604,4.083 false 0.406,0.396 0.563,0.552 0.156,0.156 10 false *1 1.438,1.104 1.594,1.26 0.156,0.156 10 false *1 1.042,1.208 1.198,1.365 0.156,0.156 10 false *2 2.323,0.094 2.479,0.25 0.156,0.156 10 false *3 2.396,1.25 2.552,1.406 0.156,0.156 10 false *4 2.135,2.521 2.292,2.677 0.156,0.156 10 false *4 0.698,2.583 0.854,2.74 0.156,0.156 10 false *6 2.823,2.552 2.979,2.708 0.156,0.156 10 false *7 2.667,3.75 2.823,3.906 0.156,0.156 10 false *5 1.938,2.979 2.094,3.135 0.156,0.156 10 false *1 1.625,3.99 1.781,4.146 0.156,0.156 10 false *4

Install SST (pressure gauge) using other SST as shown in the illustration.

Text in Illustration
*1 SST
(Hose Band)
*2 SST
(T-joint)
*3 SST
(Pressure Gauge)
*4 SST
(Hose)
*5 SST
(Fuel Tube Connector)
*6 Fuel Tube
*7 Fuel Pipe

SST
09268-31014  (09268-41500, 09268-41700, 95336-08070)
09268-45014  (09268-41200, 09268-41220, 09268-41250)


f.

Clean up any spilled gasoline.


g.

Connect the cable to the negative (-) auxiliary battery terminal.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



h.

Connect the GTS to the DLC3.


i.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.


j.

Measure the fuel pressure.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)


·

If the fuel pressure is greater than the standard value, replace the fuel pressure regulator.

·

If the fuel pressure is less than the standard value, check the fuel hoses and connections, fuel pump, fuel filter and fuel pressure regulator.



k.

Disconnect the GTS from the DLC3.


l.

Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


m.

Start the engine.


n.

Measure the fuel pressure at idle.

Standard fuel pressure:

304 to 343 kPa (3.1 to 3.5 kgf/cm2, 44 to 50 psi)



o.

Stop the engine.


p.

Check that the fuel pressure remains as specified for 5 minutes after the engine stops.

Standard fuel pressure:

147 kPa (1.5 kgf/cm2, 21 psi) or more


If the fuel pressure is not as specified, check the fuel pump or fuel injector.


q.

After checking the fuel pressure, disconnect the cable from the negative (-) auxiliary battery terminal and carefully remove SST to prevent gasoline from spraying.

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).



r.

Reconnect the fuel tube to the main fuel tube (fuel tube connector).


s.

Install the No. 1 fuel pipe clamp to the fuel tube connector.


t.

Inspect for fuel leaks (Step 1).