Home › Engine / Hybrid System › 2ZR-FXE (EMISSION CONTROL) › CANISTER
RM2070E _51 Engine / Hybrid System _061909 2ZR-FXE EMISSION CONTROL _0301612 CANISTER A

2ZR-FXE EMISSION CONTROL  CANISTER  REMOVAL  


PROCEDURE

Hide 77020A 1.REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP AND GAUGE

Hide 23220A 3.REMOVE FUEL PUMP WITH FILTER ASSEMBLY

a.
A222035

Disconnect the connector of the fuel pump harness.


b.
A216421

Disconnect the fuel pump filter hose.


c.
A159120E02
2.736,1.45 3.032,1.45 false 2.811,0.287 3.107,0.287 false 3.135,0.195 3.333,0.448 0.198,0.253 10 *1 3.049,1.364 3.232,1.617 0.183,0.253 10 *2

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws, and remove the fuel filter and fuel pump from the fuel sub-tank.

Text in Illustration
*1 Fuel Tube
*2 Fuel Sub-tank

NOTICE:

Do not do anything which may separate the fuel tube from either the fuel suction plate or fuel filter assembly, such as applying excessive force to the tube (See page Engine / Hybrid System>2ZR-FXE (FUEL)>FUEL SYSTEM>PRECAUTION).



d.
A159121

Using a screwdriver with its tip wrapped in protective tape, disengage the 2 claws and remove the No. 1 fuel suction support.


e.
A192527E08
0.688,1.469 0.323,1.469 false 2.5,2.719 2.927,2.719 false 0.125,1.375 0.302,1.563 0.177,0.188 10 false *1 2.958,2.615 3.146,2.844 0.188,0.229 10 false *2

Using a screwdriver with its tip wrapped in protective tape, disengage the 5 claws, and remove the fuel pump from the fuel filter.

Text in Illustration
*1 Fuel Filter
*2 Suction Filter

NOTICE:
·

Do not damage the fuel filter.

·

Do not remove the suction filter.

·

Do not use either the fuel pump or the suction filter if the suction filter is removed from the fuel pump.




f.
A216419

Disconnect the fuel pump harness connector.


g.
A192533E25
0.917,4.021 0.99,4.156 0.99,4.156 1.229,4.156 false 2.229,0.667 2.427,0.469 2.427,0.469 2.594,0.469 false 2.229,0.833 2.625,0.833 false 2.625,0.365 2.823,0.573 0.198,0.208 10 false *1 2.646,0.729 2.833,1.083 0.188,0.354 10 false *2 1.938,2.229 2.115,2.458 0.177,0.229 10 false *a 1.885,1.656 2.063,1.813 0.177,0.156 10 false *a 1.26,4.052 1.448,4.24 0.188,0.188 10 false *1

Remove the O-ring and spacer from the fuel pump.

Text in Illustration
*1 O-ring
*2 Spacer
*a 5.0 mm (0.197 in.)

NOTICE:

Be careful not to damage the sealing surface.


HINT:

If the O-ring still remains in the fuel filter, remove it using a wire tip (1 mm diameter) that is formed as shown in the illustration.



Hide 23280J 4.REMOVE FUEL PRESSURE REGULATOR ASSEMBLY

a.
A126640

Using a screwdriver with its tip wrapped in protective tape, remove the fuel pressure regulator assembly.

NOTICE:

Slowly pull out the fuel pressure regulator assembly because the O-ring is firmly installed between the regulator and the fuel filter.



b.
A148186E24
0.422,0.343 0.601,0.481 0.179,0.138 10 *1 1.588,0.646 1.588,0.423 1.588,0.423 0.629,0.423 false 0.928,1.408 0.928,0.423 false

Remove the 2 O-rings from the pressure regulator assembly.

Text in Illustration
*1 O-ring