Home › Engine / Hybrid System › 2ZR-FXE (COOLING) › COOLANT (for Engine) › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061911 2ZR-FXE COOLING _0301623 COOLANT(for Engine) A

2ZR-FXE COOLING  COOLANT(for Engine)  REPLACEMENT  


PROCEDURE

Hide 1.DRAIN COOLANT (for Engine)

NOTICE:

Do not remove the reserve tank cap and radiator drain cock plug while the engine and radiator are still hot. Pressurized, hot engine coolant and steam may be released and cause serious burns.


a.
A255199

Loosen the radiator drain cock plug.


b.

Remove the reserve tank cap and drain the coolant.

A262474E03
4.115,5.135 3.917,5.135 3.917,5.135 3.563,4.313 false 2.25,1.292 2.583,1.292 2.583,1.292 3.188,2.271 false 2.104,1.208 2.313,1.354 0.208,0.146 10 false *1 4.135,5.063 4.396,5.271 0.26,0.208 10 false *2

Text in Illustration
*1 Reserve Tank Cap *2 Radiator Drain Cock Plug

HINT:

Collect the coolant in a container and dispose of it according to local regulations.



Hide 2.ADD COOLANT (for Engine)

a.

Tighten the radiator drain cock plug.


b.

Remove the reserve tank cap.


c.
A213418E01
1.514,0.627 1.963,1.411 1.963,1.411 2.07,1.411 false 2.115,1.335 2.274,1.481 0.159,0.147 10 *1

Add coolant up to the B line of the reserve tank.

Text in Illustration
*1 B Line

Standard Capacity:
Item Capacity
Engine coolant w/ Exhaust Heat Recirculation System:
6.9 liters (7.3 US qts, 6.1 lmp. qts)
w/o Exhaust Heat Recirculation System:
6.5 liters (6.9 US qts, 5.7 lmp. qts)


HINT:

TOYOTA vehicles are filled with TOYOTA SLLC at the factory. In order to avoid damage to the engine cooling system and other technical problems, only use TOYOTA SLLC or similar high quality ethylene glycol based non-silicate, non-amine, non-nitrite, non-borate coolant with long-life hybrid organic acid technology (coolant with long-life hybrid organic acid technology is a combination of low phosphates and organic acids).


NOTICE:

Never use water as a substitute for engine coolant.



d.

Squeeze the inlet and outlet radiator hoses several times by hand, and then check the level of the coolant.

If the coolant level is low, add coolant.


e.

Install the reserve tank cap.


f.

Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


g.

Bleed air from the cooling system.

NOTICE:
·

Before starting the engine, turn the A/C switch off.

·

Adjust the heater control to the maximum hot setting.

·

Adjust the blower speed to the low setting.



i.

Warm up the engine until the thermostat opens. While the thermostat is open, allow the coolant to circulate for several minutes.

HINT:

The thermostat opening timing can be confirmed by squeezing the inlet radiator hose by hand, and sensing vibrations when the engine coolant starts to flow inside the hose.


CAUTION:
When squeezing the radiator hose:
·

Wear protective gloves.

·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the radiator fan.




ii.

Squeeze the inlet and outlet radiator hoses several times by hand to bleed air from the system.

CAUTION:
When squeezing the radiator hose:
·

Wear protective gloves.

·

Be careful as the radiator hoses are hot.

·

Keep your hands away from the radiator fan.





h.
A213418E12
1.5,0.99 2.135,1.802 2.135,1.802 2.198,1.802 false 1.5,0.823 2.094,1.5 2.094,1.5 2.156,1.5 false 2.198,1.427 2.354,1.573 0.156,0.146 10 false *1 2.229,1.729 2.385,1.875 0.156,0.146 10 false *2

After the engine has cooled down, check that the coolant level is between the full and low lines.

Text in Illustration
*1 Full Line
*2 Low Line

If the coolant level is low, add coolant up to the full line on the reserve tank.