Home › Engine / Hybrid System › 2ZR-FXE (LUBRICATION) › OIL AND OIL FILTER › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061912 2ZR-FXE LUBRICATION _0301633 OIL AND OIL FILTER A

2ZR-FXE LUBRICATION  OIL AND OIL FILTER  REPLACEMENT  


CAUTION / NOTICE / HINT

CAUTION:
·

Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

·

Wear protective clothing and gloves. Avoid contact with used oil. If contact occurs, wash your skin thoroughly with soap or waterless hand cleaner. Never use gasoline, thinners, or solvents to wash the skin.

·

In order to protect the environment, dispose of used oil and used oil filters at designated disposal sites only.



PROCEDURE

Hide 1.REMOVE OIL FILTER ELEMENT SERVICE HOLE COVER

a.
A228174

Remove the 3 clips.


b.
A228175

Pull the oil filter element service hole cover to open it.

HINT:

Fully open the service hole cover and fold it at a 180° angle.



c.
A228177E01
0.649,1.425 0.861,1.606 0.213,0.181 10 *1 0.775,1.126 0.775,1.416 false

Using one of the removed clips, secure the service hole cover with it folded at a 180° angle.

Text in Illustration
*1 Clip


Hide 2.DRAIN ENGINE OIL

a.

Remove the oil filler cap.


b.

Remove the oil pan drain plug and gasket, and drain the oil into a container.


c.

Clean and install the oil pan drain plug with a new gasket.

Torque:
37 N*m (377 kgf*cm, 27 ft.*lbf)


Hide 15620 3.REMOVE OIL FILTER CAP ASSEMBLY

a.
A198241E04
0.128,0.916 0.441,1.065 0.313,0.149 10 SST 0.495,0.999 0.626,0.999 0.626,0.999 0.817,1.209 false 1.359,1.547 1.645,0.167 1.645,0.167 1.888,0.167 false 0.838,1.971 1.27,2.551 1.27,2.551 1.27,2.718 false 1.925,0.081 2.082,0.249 0.157,0.168 10 *1 1.184,2.737 1.357,2.884 0.173,0.146 10 *2

Using SST, loosen the oil filter cap 4 revolutions, align the cap ribs vertically, and drain the remaining engine oil in the oil filter cap.

Text in Illustration
*1 Cap Rib
*2 Oil Filter Bracket Clip

SST
09228-06501  

NOTICE:

Do not remove the oil filter bracket clip when removing the oil filter cap assembly.


HINT:

Set a container below the oil filter cap assembly before loosening the oil filter cap.



b.

Remove the oil filter cap assembly.


c.
A218052E01
1.162,0.366 0.746,0.366 false 2.381,1.203 2.735,0.849 2.735,0.849 2.869,0.849 false 0.54,0.271 0.715,0.436 0.175,0.165 10 *1 2.903,0.776 3.098,0.925 0.195,0.149 10 *2

Remove the oil filter element and O-ring from the oil filter cap.

Text in Illustration
*1 Oil Filter Element
*2 O-ring

NOTICE:

Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring on the cap.



Hide 15620 4.INSTALL OIL FILTER CAP ASSEMBLY

a.

Clean the oil filter cap threads and O-ring groove.


b.

Apply a small amount of engine oil to a new O-ring and install it to the oil filter cap.


c.

Set a new oil filter element in the oil filter cap.


d.

Remove any dirt or foreign matter from the installation surface and inside of the engine.


e.
A161887

Reapply a small amount of engine oil to the O-ring of the oil filter cap assembly. Align the cutout in the oil filter cap threads 90° to the grooves in the oil filter bracket and temporarily tighten the cap.

NOTICE:

Make sure that the O-ring does not get caught between the parts.



f.
A198242E10
1.448,0.323 1.667,0.323 1.667,0.323 1.948,1.521 false 1.542,2.177 1.771,2.615 1.771,2.615 1.771,2.833 false 1.104,1.042 1.375,1.042 1.375,1.042 1.656,1.385 false 0.813,0.958 1.115,1.115 0.302,0.156 10 false SST 1.26,0.24 1.458,0.385 0.198,0.146 10 false *a 1.698,2.854 1.875,3.042 0.177,0.188 10 false *1

Using SST, tighten the oil filter cap assembly.

Text in Illustration
*1 Oil Filter Bracket Clip
*a No Clearance

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

SST
09228-06501  

NOTICE:
·

After tightening the oil filter cap assembly, check for gaps between the installation surfaces.

·

Do not remove the oil filter bracket clip when installing the oil filter cap assembly.

·

Do not cross thread the oil filter cap assembly.




Hide 5.ADD ENGINE OIL

a.

Add new engine oil and install the oil filler cap.

Standard Oil Grade
Oil Grade Oil Viscosity (SAE)
API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil
·

0W-20


·

5W-20


·

5W-30


·

10W-30


API grade SL, SM or SN multigrade engine oil
·

15W-40


·

20W-50



Standard Capacity
Item Standard Condition
Drain and refill with oil filter change 4.2 liters (4.4 US qts, 3.7 lmp. qts)
Drain and refill without oil filter change 3.9 liters (4.1 US qts, 3.4 lmp. qts)
Dry fill 4.7 liters (5.0 US qts, 4.1 lmp. qts)


Hide 6.INSPECT FOR ENGINE OIL LEAK

a.

Put the engine in inspection mode (See page General>INTRODUCTION>REPAIR INSTRUCTION>INSPECTION MODE PROCEDURE).


b.

Start the engine.


c.

Check for engine oil leaks from the oil filter cap and oil pan drain plug.


Hide 7.INSTALL OIL FILTER ELEMENT SERVICE HOLE COVER

a.
A228177E01
0.649,1.425 0.861,1.606 0.213,0.181 10 *1 0.775,1.126 0.775,1.416 false

Remove the clip.

Text in Illustration
*1 Clip


b.
A228176

Close the service hole cover.

HINT:
·

Push the oil filter element service hole cover towards the vehicle to remove the crease.

·

If the crease remains, the service hole cover may look as though it does not fit properly after the clips are installed.




c.
A228174

Install the oil filter element service hole cover with the 3 clips.