Home › Engine / Hybrid System › CRUISE CONTROL › CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301639 CRUISE CONTROL SYSTEM U

CRUISE CONTROL  CRUISE CONTROL SYSTEM  DATA LIST / ACTIVE TEST  


DATA LIST


HINT:

Using the GTS to read the Data List allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Cruise Control / Data List.


e.

According to the display on the GTS, read the Data List.

Cruise Control
Tester Display Measurement Item/Range Normal Condition Diagnostic Note
CCS Vehicle Spd Vehicle speed/min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) Actual vehicle speed is displayed -
CCS Mem Vehicle Spd Vehicle speed/min.: 0 km/h (0 mph), max.: 255 km/h (159 mph) Actual vehicle speed stored in memory -
Cruise Control Cruise control / ON or OFF ON: Cruise control activated
OFF: Cruise control deactivated
-
Main SW M-CPU Cruise control switch (Main-CPU) / ON or OFF ON: Cruise control switch (ON-OFF button) pushed
OFF: Cruise control switch (ON-OFF button) released
-
CCS Ready M-CPU Cruise control system standby condition (Main-CPU) / ON or OFF Each time cruise control switch (ON-OFF button) is pushed, ON/OFF changes -
CCS Indicator M-CPU Cruise control indicator (Main-CPU) / ON or OFF ON: Cruise control indicator light illuminated in green
OFF: Cruise control indicator light not on
-
Cancel Switch CANCEL switch signal / ON or OFF ON: CANCEL switch on
OFF: CANCEL switch off
-
SET/COAST Switch -/SET switch signal / ON or OFF ON: -/SET switch on
OFF: -/SET switch off
-
RES/ACC Switch +/RES switch signal / ON or OFF ON: +/RES switch on
OFF: +/RES switch off
-
Stp Light SW M-CPU Stop light switch signal (Main CPU) / ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released
-
Cruise Operation Status Shift position signal (D position) / ON or OFF ON: Shift lever in D
OFF: Shift lever not in D
-
Cruise Request Driving Force Cruise control driving force signal/min.: -51.2 kN, max.: 51.2 kN Actual driving force -



ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

According to the display on the GTS, perform the "Active Test".

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise control indicator light Cruise control indicator (illuminated in green) ON / OFF -
Indicat. SET Cruise control SET indicator light Cruise control SET indicator ON / OFF -
Cruise Indicator Cruise control indicator light Cruise control indicator (illuminated in amber) ON / OFF -