Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2014.11
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM U

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TERMINALS OF ECU  


CHECK DRIVING SUPPORT ECU


U155056E02
3.563,0.292 3.844,0.458 0.281,0.167 10 false L60

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L60-7 (MODE) - L60-25 (GND) R - W-B Steering pad switch signal
(distance control signal)
Power switch on (IG)
Distance control switch off
11 to 14 V
L60-7 (MODE) - L60-25 (GND) R - W-B Steering pad switch signal
(distance control signal)
Power switch on (IG)
Distance control switch on
Below 2 V
L60-10 (CCHG) - L60-25 (GND) G - W-B Cruise control switch signal Power switch on (IG),
MODE switch off
11 to 14 V
L60-10 (CCHG) - L60-25 (GND) G - W-B Cruise control switch signal Power switch on (IG),
MODE switch on
Below 2 V
L60-17 (CA2L) - L60-25 (GND) R - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 1)
L60-16 (LRDD) - L60-25 (GND) V - W-B Millimeter wave radar sensor Power switch on (IG) Pulse generation
(See waveform 2)
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control switch signal Power switch on (IG) 1 MΩ or higher
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control switch signal CANCEL switch on 1509 to 1571 Ω
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control switch signal -/SET switch on 617 to 643 Ω
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control switch signal +/RES switch on 235 to 245 Ω
L60-23 (CCS) - L60-25 (GND) V - W-B Cruise control switch signal Cruise control switch on Below 2.5 Ω
L60-25 (GND) - Body ground W-B - Body ground Earth (ground circuit of driving support ECU) Always Below 1 Ω
L60-27 (STP-) - L60-25 (GND) Y - W-B Stop light signal Brake pedal released Below 1 V
L60-27 (STP-) - L60-25 (GND) Y - W-B Stop light signal Brake pedal depressed 11 to 14 V
L60-28 (ST1-) - L60-25 (GND) V - W-B Stop light signal Power switch on (IG),
Brake pedal released
11 to 14 V
L60-28 (ST1-) - L60-25 (GND) V - W-B Stop light signal Power switch on (IG),
Brake pedal depressed
Below 1 V
L60-30 (B) - L60-25 (GND) B - W-B Power source Power switch on (IG) 11 to 14 V
L60-32 (WIP2) - L60-25 (GND) P - W-B Wiper switch signal Power switch on (IG),
Wiper switch off
Below 2.4 V
L60-32 (WIP2) - L60-25 (GND) P - W-B Wiper switch signal Power switch on (IG),
Wiper switch HI position
11 to 14 V
L60-38 (LRRD) - L60-25 (GND) L - W-B Millimeter wave radar sensor output signal Power switch on (IG) Pulse generation
(See waveform 3)
L60-39 (CA2H) - L60-25 (GND) B - W-B CAN communication signal Power switch on (IG) Pulse generation
(See waveform 4)

a.
A306171E05
3.031,1.365 3.427,1.573 0.396,0.208 10 false GND 2.792,0.271 3.406,0.521 0.615,0.25 10 false 1 V/DIV. 1.333,1.885 2.354,2.146 1.021,0.26 10 false 10 μsec./DIV.

WAVEFORM 1

i.

CAN communication signal

Driving support ECU Terminal Name Between L60-17 (CA2L) and L60-25 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
E109730E18
2.969,1.188 3.417,1.604 0.448,0.417 10 false GND 1.323,1.906 2.292,2.115 0.969,0.208 10 false 10 μsec./DIV. 0.094,0.208 0.667,0.438 0.573,0.229 10 false 2 V/DIV.

WAVEFORM 2

i.

Millimeter wave radar sensor input signal

Driving support ECU Terminal Name Between L60-16 (LRDD) and L60-25 (GND)
Tester Range 2 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)



c.
E109731E18
2.969,1.188 3.427,1.698 0.458,0.51 10 false GND 1.302,1.906 2.313,2.115 1.01,0.208 10 false 10 μsec./DIV. 0.083,0.219 0.854,0.458 0.771,0.24 10 false 2 V/DIV.

WAVEFORM 3

i.

Millimeter wave radar sensor output signal

Driving support ECU Terminal Name Between L60-38 (LRRD) and L60-25 (GND)
Tester Range 2 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)



d.
U190496E02
2.76,0.271 3.302,0.469 0.542,0.198 10 false 1 V/DIV. 1.302,1.938 2.156,2.104 0.854,0.167 10 false 10 μsec./DIV.

WAVEFORM 4

i.

CAN communication signal

Driving support ECU Terminal Name Between L60-39 (CA2H) and L60-25 (GND)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK POWER MANAGEMENT CONTROL ECU


U191244E02
1.167,0.594 1.438,0.771 0.271,0.177 10 false A21 2.635,0.594 2.927,0.771 0.292,0.177 10 false A22 4.323,0.594 4.521,0.771 0.198,0.177 10 false L5 5.677,0.594 5.875,0.771 0.198,0.177 10 false L6

Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
L5-6 (E1) - Body ground W-B - Body ground Earth (ground) circuit of power management control ECU Always Below 1 Ω
L5-11 (TC) - L5-6 (E1) P - W-B Terminal TC of DLC3 Power switch on (IG) 11 to 14 V
L5-11 (TC) - L5-6 (E1) P - W-B Terminal TC of DLC3 Terminals TC and CG of DLC3 connected Below 1 V
L5-34 (CA2H) - L5-6 (E1) B - W-B CAN communication line Power switch on (IG) Pulse generation
(see waveform 1)
L5-35 (CA2L) - L5-6 (E1) W - W-B CAN communication line Power switch on (IG) Pulse generation
(see waveform 2)
L6-24 (CA1L) - L5-6 (E1) P - W-B CAN communication line Power switch on (IG) Pulse generation
(see waveform 2)
L6-25 (CA1H) - L5-6 (E1) V - W-B CAN communication line Power switch on (IG) Pulse generation
(see waveform 1)

a.
A306170E02
3.021,1.406 3.427,1.656 0.406,0.25 10 false GND 1.313,1.917 2.333,2.146 1.021,0.229 10 false 10 μsec./DIV. 2.781,0.292 3.385,0.531 0.604,0.24 10 false 1 V/DIV.

WAVEFORM 1

i.

CAN communication signal

Power management control ECU Terminal Name Between L6-25 (CA1H) - L5-6 (E1) or L5-34 (CA2H) - L5-6 (E1)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.




b.
A306171E05
3.031,1.365 3.427,1.573 0.396,0.208 10 false GND 2.792,0.271 3.406,0.521 0.615,0.25 10 false 1 V/DIV. 1.333,1.885 2.354,2.146 1.021,0.26 10 false 10 μsec./DIV.

WAVEFORM 2

i.

CAN communication signal

Power management control ECU Terminal Name Between L6-24 (CA1L) - L5-6 (E1) or L5-35 (CA2L) - L5-6 (E1)
Tester Range 1 V/DIV., 10 μsec./DIV.
Condition Power switch on (IG)

HINT:

The waveform varies depending on the CAN communication signal.





CHECK MILLIMETER WAVE RADAR SENSOR


U191318E02
2.031,0.833 2.396,1 0.365,0.167 10 false A2

Terminal No. (Symbols) Wiring Color Terminal Description Condition Specified Condition
A2-2 (SGND) - Body ground W-B - Body ground Ground Always Below 1 Ω
A2-3 (LRDD) - A2-2 (SGND) V - W-B Millimeter wave radar sensor output signal Power switch on (IG) Pulse generation
(see waveform 1)
A2-4 (LRRD) - A2-2 (SGND) L - W-B Millimeter wave radar sensor input signal Power switch on (IG) Pulse generation
(see waveform 2)
A2-5 (IGB) - A2-2 (SGND) R - W-B Power source Power switch on (IG) 10 to 14 V

a.
E109730E19
2.948,1.177 3.375,1.385 0.427,0.208 10 false SGND 1.24,1.917 2.271,2.135 1.031,0.219 10 false 10 msec./DIV. 0.104,0.198 0.771,0.438 0.667,0.24 10 false 2 V/DIV

WAVEFORM 1

Item Contents
Terminal LRDD - SGND
Tool setting 2 V/DIV., 10 msec./DIV.
Vehicle condition Power switch on (IG)


b.
E109731E19
2.958,1.167 3.354,1.375 0.396,0.208 10 false SGND 1.281,1.906 2.292,2.094 1.01,0.188 10 false 10 msec./DIV. 0.115,0.208 0.823,0.469 0.708,0.26 10 false 2 V/DIV

WAVEFORM 2

Item Contents
Terminal LRRD - SGND
Tool setting 2 V/DIV., 10 msec./DIV.
Vehicle condition Power switch on (IG)