Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2016.05
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

·

The driving support ECU assembly controls the cruise control system based on information sent from switches, sensors and ECUs.

·

The power management control ECU sends current to the IG1 No. 1 relay. This closes the contact points in the relay so that power is supplied to the driving support ECU assembly B terminal.


WIRING DIAGRAM

E232845E01
5.832,0.646 6.085,0.816 0.253,0.170 10 B 5.827,1.921 6.181,2.090 0.354,0.170 10 GND 5.572,1.812 5.749,1.981 0.177,0.170 10 25 5.56,0.545 5.737,0.715 0.177,0.170 10 30 2.589,1.291 3.376,1.624 0.787,0.333 10 IG1 No. 1 3.265,0.78 4.179,0.941 0.914,0.161 10 ECU-IG No. 2 0.887,0.801 1.368,0.962 0.481,0.161 10 DC/DC 0.763,2.793 1.365,3.155 0.601,0.362 10 Auxiliary Battery 5.524,2.702 5.816,2.872 0.291,0.170 10 L60 5.524,2.87 6.920,3.040 1.395,0.170 10 Driving Support ECU 3.25,2.815 4.532,3.151 1.282,0.336 10 Power Management Control ECU 1.957,1.732 4.665,1.942 2.708,0.210 10 Instrument Panel Junction Block Assembly 0.628,1.893 1.049,2.063 0.421,0.170 10 MAIN 2.127,2.716 2.376,2.886 0.250,0.170 10 2 2.366,2.809 2.767,2.978 0.401,0.170 10 IG1D 3.25,2.65 3.490,2.820 0.240,0.170 10 L6 4.353,1.074 4.542,1.229 0.189,0.155 10 2B 4.4,0.876 4.496,1.032 0.096,0.155 10 6 4.353,0.637 4.542,0.792 0.189,0.155 10 2B 4.358,0.439 4.539,0.594 0.181,0.155 10 16 2.143,1.074 2.332,1.229 0.189,0.155 10 2B 2.143,0.876 2.317,1.032 0.174,0.155 10 25 2.143,0.637 2.332,0.792 0.189,0.155 10 2E 2.19,0.439 2.286,0.594 0.096,0.155 10 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
U155036E02
1.75,1.927 1.583,2.531 true 0.24,0.302 0.594,0.573 0.354,0.271 10 false *a 1.531,2.552 1.781,2.74 0.25,0.188 10 false B 0.427,1.042 0.688,1.219 0.26,0.177 10 false L60

Disconnect the driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-30 (B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


d.

Reconnect the driving support ECU assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
U155037E02
1.292,1.927 0.958,2.667 true 0.167,0.146 0.521,0.417 0.354,0.271 10 false *a 0.792,2.677 1.281,2.865 0.49,0.188 10 false GND 0.438,1.063 0.698,1.24 0.26,0.177 10 false L60

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-25 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


c.

Reconnect the driving support ECU assembly connector.



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

U155119E03
1.677,4.063 1.938,4.26 0.26,0.198 10 false 2E 4.927,4.073 5.177,4.281 0.25,0.208 10 false 2B 6.229,1.344 6.448,1.521 0.219,0.177 10 false 2B 0.708,2.75 0.927,2.917 0.219,0.167 10 false 2E 0.281,0.156 0.552,0.396 0.271,0.24 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2B-16 Always 10 kΩ or higher
2E-1 - 2B-16 Auxiliary battery voltage applied between terminals 2B-25 and 2B-6 Below 1 Ω


Text in Illustration
*a Instrument Panel Junction Block Assembly - -


c.

Reinstall the instrument panel junction block assembly.



OK

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - INSTRUMENT PANEL JUNCTION BLOCK)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the driving support ECU assembly connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-30 (B) - 2B-16 Always Below 1 Ω



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the driving support ECU assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU - INSTRUMENT PANEL JUNCTION BLOCK)

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.
U155073E03
0.208,0.177 0.406,0.375 0.198,0.198 10 false *a 1.729,1.021 1.917,1.198 0.188,0.177 10 false 2B

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2B-6 - Body ground Always Below 1 Ω


Text in Illustration
*a Instrument Panel Junction Block Assembly


c.

Reconnect the instrument panel junction block assembly connector.



OK

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the power management control ECU connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2B-25 - L6-2 (IG1D) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
2B-25 or L6-2 (IG1D) - Body ground Always 10 kΩ or higher



d.

Reconnect the power management control ECU connector.


e.

Reconnect the instrument panel junction block assembly connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER MANAGEMENT CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)