Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.05–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  ECU Power Source Circuit  


DESCRIPTION

·

The driving support ECU assembly controls the cruise control system based on information sent from switches, sensors and ECUs.

·

The hybrid vehicle control ECU sends current to the IG1 No. 1 relay. This closes the contact points in the relay so that power is supplied to the driving support ECU assembly B terminal.


WIRING DIAGRAM

E232845E10
5.833,0.625 6.083,0.792 0.25,0.167 10 false B 5.823,1.906 6.177,2.073 0.354,0.167 10 false GND 5.573,1.792 5.75,1.958 0.177,0.167 10 false 25 5.563,0.521 5.74,0.688 0.177,0.167 10 false 30 2.594,1.333 3.385,1.667 0.792,0.333 10 false IG1 No. 1 3.26,0.802 4.177,0.958 0.917,0.156 10 false ECU-IG No. 2 0.885,0.823 1.365,0.979 0.479,0.156 10 false DC/DC 0.76,2.771 1.365,3.135 0.604,0.365 10 false Auxiliary Battery 5.521,2.688 5.813,2.854 0.292,0.167 10 false L60 5.521,2.854 6.917,3.021 1.396,0.167 10 false Driving Support ECU 3.25,2.792 4.833,3.146 1.583,0.354 10 false Certification ECU (Smart Key ECU Assembly) 1.958,1.75 4.667,1.958 2.708,0.208 10 false Instrument Panel Junction Block Assembly 0.625,1.906 1.042,2.073 0.417,0.167 10 false MAIN 2.167,2.698 2.417,2.865 0.25,0.167 10 false 6 2.365,2.792 2.76,2.958 0.396,0.167 10 false IG1D 3.25,2.635 3.833,2.802 0.583,0.167 10 false L197 4.313,1.083 4.5,1.24 0.188,0.156 10 false 2B 4.365,0.865 4.458,1.021 0.094,0.156 10 false 6 4.323,0.646 4.51,0.802 0.188,0.156 10 false 2B 4.313,0.427 4.49,0.583 0.177,0.156 10 false 16 2.167,1.083 2.354,1.24 0.188,0.156 10 false 2B 2.177,0.875 2.354,1.031 0.177,0.156 10 false 25 2.167,0.646 2.354,0.802 0.188,0.156 10 false 2E 2.188,0.417 2.281,0.573 0.094,0.156 10 false 1

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK DRIVING SUPPORT ECU ASSEMBLY (B VOLTAGE)
a.
U155036E02
1.75,1.927 1.583,2.531 true 0.24,0.302 0.594,0.573 0.354,0.271 10 false *a 1.531,2.552 1.781,2.74 0.25,0.188 10 false B 0.427,1.042 0.688,1.219 0.26,0.177 10 false L60

Disconnect the driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-30 (B) - Body ground Power switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


d.

Reconnect the driving support ECU assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

NG

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)
a.
U155037E02
1.292,1.927 0.958,2.667 true 0.167,0.146 0.521,0.417 0.354,0.271 10 false *a 0.792,2.677 1.281,2.865 0.49,0.188 10 false GND 0.438,1.063 0.698,1.24 0.26,0.177 10 false L60

Disconnect the driving support ECU assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-25 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU Assembly)


c.

Reconnect the driving support ECU assembly connector.



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU ASSEMBLY - BODY GROUND)

3.INSPECT INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY
a.

Remove the instrument panel junction block assembly.

U155119E03
1.677,4.063 1.938,4.26 0.26,0.198 10 false 2E 4.927,4.073 5.177,4.281 0.25,0.208 10 false 2B 6.229,1.344 6.448,1.521 0.219,0.177 10 false 2B 0.708,2.75 0.927,2.917 0.219,0.167 10 false 2E 0.281,0.156 0.552,0.396 0.271,0.24 10 false *a


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
2E-1 - 2B-16 Always 10 kΩ or higher
2E-1 - 2B-16 Auxiliary battery voltage applied between terminals 2B-25 and 2B-6 Below 1 Ω


Text in Illustration
*a Instrument Panel Junction Block Assembly - -


c.

Reinstall the instrument panel junction block assembly.



OK

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - INSTRUMENT PANEL JUNCTION BLOCK)

NG

REPLACE INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT ECU - INSTRUMENT PANEL JUNCTION BLOCK)
a.

Disconnect the driving support ECU assembly connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-30 (B) - 2B-16 Always Below 1 Ω



d.

Reconnect the instrument panel junction block assembly connector.


e.

Reconnect the driving support ECU assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT ECU - INSTRUMENT PANEL JUNCTION BLOCK)

5.CHECK HARNESS AND CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)
a.
U155073E03
0.208,0.177 0.406,0.375 0.198,0.198 10 false *a 1.729,1.021 1.917,1.198 0.188,0.177 10 false 2B

Disconnect the instrument panel junction block assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2B-6 - Body ground Always Below 1 Ω


Text in Illustration
*a Instrument Panel Junction Block Assembly


c.

Reconnect the instrument panel junction block assembly connector.



OK

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY - BODY GROUND)

6.CHECK HARNESS AND CONNECTOR (HYBRID VEHICLE CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Disconnect the instrument panel junction block assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
2B-25 - L197-6 (IG1D) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
2B-25 or L197-6 (IG1D) - Body ground Always 10 kΩ or higher



d.

Reconnect the hybrid vehicle control ECU connector.


e.

Reconnect the instrument panel junction block assembly connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (INSTRUMENT PANEL JUNCTION BLOCK - AUXILIARY BATTERY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (HYBRID VEHICLE CONTROL ECU - INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY)