Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.05–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Cruise Main Indicator Light Circuit  


DESCRIPTION

When the cruise control system is turned on using the cruise control switch (ON-OFF button), the cruise control indicator light (vehicle-to-vehicle distance control mode) illuminates in green. The driving support ECU uses these and other indicators to indicate the control condition (presence or absence of a vehicle in front, vehicle-to-vehicle distance, and set vehicle speed) and fail-safe state through the CAN communication system.

HINT:

If the preceding vehicle in the same lane significantly decreases vehicle speed or another vehicle moves in front of your vehicle, adequate deceleration cannot be applied by the cruise control system and the vehicle-to-vehicle distance will become shorter. At this time, the system sounds the buzzer to warn the driver. The indicators for the dynamic radar cruise control system use CAN for communication. Therefore, if there are any indicator malfunctions, check for DTCs in the CAN communication system before troubleshooting this circuit.


WIRING DIAGRAM

E187973E52
1.323,0.604 1.771,0.771 0.448,0.167 10 false CANH 1.344,1.104 1.792,1.271 0.448,0.167 10 false CANL 2.958,0.604 3.406,0.771 0.448,0.167 10 false CA1H 2.979,1.115 3.427,1.281 0.448,0.167 10 false CA1L 5.542,0.604 5.99,0.771 0.448,0.167 10 false CA2H 5.542,1.115 5.99,1.281 0.448,0.167 10 false CA2L 3.917,0.604 4.365,0.771 0.448,0.167 10 false CA2H 3.917,1.115 4.365,1.281 0.448,0.167 10 false CA2L 1.781,0.417 1.979,0.573 0.198,0.156 10 false 19 1.781,0.917 1.979,1.073 0.198,0.156 10 false 20 4.438,0.417 4.635,0.573 0.198,0.156 10 false 34 4.438,0.906 4.635,1.063 0.198,0.156 10 false 35 2.688,0.417 2.885,0.573 0.198,0.156 10 false 25 2.688,0.906 2.885,1.063 0.198,0.156 10 false 24 5.313,0.427 5.51,0.583 0.198,0.156 10 false 39 5.313,0.927 5.51,1.083 0.198,0.156 10 false 17 2.677,0.594 2.896,0.771 0.219,0.177 10 false L6 2.677,1.094 2.896,1.271 0.219,0.177 10 false L6 4.438,0.594 4.656,0.771 0.219,0.177 10 false L5 4.438,1.094 4.656,1.271 0.219,0.177 10 false L5 0.26,1.635 0.552,1.792 0.292,0.156 10 false L27 0.552,1.635 2.542,2.208 1.99,0.573 10 false Combination Meter 2.781,1.688 4.708,2.115 1.927,0.427 10 false Hybrid Vehicle Control ECU 5.51,1.635 5.865,1.833 0.354,0.198 10 false L60 5.813,1.635 7.156,2.01 1.344,0.375 10 false Driving Support 0.844,2.469 1.917,2.656 1.073,0.188 10 false : CAN Bus Line

PROCEDURE

1.PERFORM ACTIVE TEST USING GTS
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Body Electrical / Combination Meter / Active Test.


e.

Check the cruise control indicator light by performing Active Test.

Combination Meter
Tester Display Test Part Control Range Diagnostic Note
Indicat. Lamp Cruise Cruise control indicator light
(Constant speed control mode)
OFF or ON Confirm that the vehicle is stopped with engine idling
Indicat. Radar Cruise Cruise control indicator light
(Vehicle-to-vehicle distance control mode)
OFF or ON Confirm that the vehicle is stopped with engine idling

OK:

The display changes in accordance with Active Test operation.




OK

REPLACE PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG