Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2012.03–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Wiper Signal Circuit  


DESCRIPTION

When the driving support ECU assembly detects that the wipers are operating at high speed, the dynamic radar cruise control system control of vehicle speed is canceled.

WIRING DIAGRAM

E234003E32
0.396,2.698 0.677,2.885 0.281,0.188 10 false L48 0.708,2.698 1.823,3.24 1.115,0.542 10 false Windshield Wiper Switch Assembly 5.365,2.74 5.656,2.906 0.292,0.167 10 false L60 5.396,1.5 5.792,1.667 0.396,0.167 10 false WIP2 5.167,1.396 5.375,1.563 0.208,0.167 10 false 32 5.656,2.74 6.677,3.281 1.021,0.542 10 false Driving Support ECU Assembly 1.958,1.406 2.167,1.573 0.208,0.167 10 false 4 1.677,1.5 1.885,1.667 0.208,0.167 10 false +2 3.604,1.646 4.323,1.813 0.719,0.167 10 false WIP No. 4

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.INSPECT DRIVING SUPPORT ECU ASSEMBLY
a.
U155035E02
1.948,1.948 2.188,2.604 false 0.448,0.417 0.635,0.615 0.188,0.198 10 false *a 0.448,1.042 0.708,1.208 0.26,0.167 10 false L60 2.052,2.625 2.469,2.865 0.417,0.24 10 false WIP2

Disconnect the driving support ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Set the windshield wiper switch assembly to the HI position.


d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L60-32 (WIP2) - Body ground Power switch on (IG), windshield wiper switch assembly Hi position 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Driving Support ECU assembly)


e.

Reconnect the driving support ECU assembly connector.



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT CONTROL ECU - WINDSHIELD WIPER SWITCH)
2.CHECK HARNESS AND CONNECTOR (DRIVING SUPPORT CONTROL ECU - WINDSHIELD WIPER SWITCH)
a.

Disconnect the driving support ECU assembly connector.


b.

Disconnect the windshield wiper switch assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L60-32 (WIP2) - L48-4 (+2) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
L60-32 (WIP2) or L48-4 (+2) - Body ground Always 10 kΩ or higher



d.

Reconnect the driving support ECU assembly connector.


e.

Reconnect the windshield wiper switch assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DRIVING SUPPORT CONTROL ECU - WINDSHIELD WIPER SWITCH)