Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.05–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  TC and CG Terminal Circuit  


DESCRIPTION

Connecting terminals TC and CG of the DLC3 causes the system to enter self-diagnostic mode. If a malfunction is present, the vehicle-to-vehicle distance control mode indicator will blink.

HINT:

When a particular warning light remains blinking, a ground short in the wiring of terminal TC of the DLC3 or an internal ground short in the relevant ECU is suspected.


WIRING DIAGRAM

E222528E19
5.719,2.677 6.083,2.875 0.365,0.198 10 false L6 5.948,2.677 6.844,3.115 0.896,0.438 10 false Hybrid Vehicle Control ECU 0.604,2.635 0.896,2.833 0.292,0.198 10 false L61 0.604,2.813 1.135,3.01 0.531,0.198 10 false DLC3 5.74,0.74 5.958,0.906 0.219,0.167 10 false 28 1.26,0.74 1.479,0.906 0.219,0.167 10 false 13 6.052,0.865 6.323,1.031 0.271,0.167 10 false TC 0.938,0.865 1.208,1.031 0.271,0.167 10 false TC 1.26,1.625 1.479,1.792 0.219,0.167 10 false 4 0.938,1.75 1.208,1.917 0.271,0.167 10 false CG

PROCEDURE

1.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - ECM)
a.

Disconnect the hybrid vehicle control ECU connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L6-28 (TC) - L61-13 (TC) Always Below 1 Ω



c.

Reconnect the hybrid vehicle control ECU connector.



OK

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - HYBRID VEHICLE CONTROL ECU)

2.CHECK HARNESS AND CONNECTOR (TERMINAL CG of DLC3 - BODY GROUND)
a.
U154771E02
1.052,1.927 1.573,1.24 false 1.583,0.313 1.865,0.49 0.281,0.177 10 false L61 0.135,0.083 0.344,0.25 0.208,0.167 10 false *a 0.917,1.938 1.188,2.104 0.271,0.167 10 false CG

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
L61-4 (CG) - Body ground Always Below 1 Ω


Text in Illustration
*a DLC3



OK

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (DLC3 - BODY GROUND)

3.CHECK HARNESS AND CONNECTOR (TERMINAL TC of DLC3 - BODY GROUND)
a.
U154772E02
2.01,1.896 1.823,1.635 false 1.573,0.323 1.854,0.5 0.281,0.177 10 false L61 0.146,0.094 0.354,0.26 0.208,0.167 10 false *a 1.969,1.917 2.24,2.083 0.271,0.167 10 false TC

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
L61-13 (TC) - Body ground Always 10 kΩ or higher


Text in Illustration
*a DLC3



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR OR EACH ECU