Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2016.05–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  Millimeter Wave Radar Sensor Power Source Circuit  


DESCRIPTION

When the power switch is turned on (IG), auxiliary battery voltage is applied to terminal IGB of the millimeter wave radar sensor assembly.

This circuit provides power to the millimeter wave radar sensor. The millimeter wave radar sensor emits radio waves towards an object in front and measures the distance and direction of the object by receiving the beam reflections. Based on the reflections, the sensor calculates the difference in speed between the vehicle and the object in front. This data is transmitted to the driving support ECU assembly.

WIRING DIAGRAM

A217937E16
0.67,2.585 1.094,2.755 0.424,0.170 10 MAIN 0.761,3.251 1.416,3.600 0.655,0.349 10 Auxiliary Battery 0.67,1.885 1.175,2.048 0.505,0.163 10 DC/DC 5.991,1.182 6.119,1.380 0.128,0.198 10 5 2.015,3.37 2.143,3.568 0.128,0.198 10 6 5.991,2.931 6.119,3.129 0.128,0.198 10 1 2.204,3.491 2.555,3.675 0.350,0.184 10 IG1D 6.169,3.043 6.596,3.227 0.427,0.184 10 SGND 6.169,1.264 6.519,1.447 0.350,0.184 10 IGB 4.082,1.446 5.383,1.669 1.302,0.223 10 ECU-IG No. 2 2.522,2.184 3.145,2.345 0.623,0.162 10 IG1 No. 1 5.411,3.566 5.762,3.713 0.350,0.147 10 A76 5.695,3.566 7.147,3.898 1.452,0.332 10 Millimeter Wave Radar Sensor Assembly 1.538,3.874 1.961,4.020 0.423,0.147 10 L197 1.892,3.873 3.761,4.205 1.869,0.332 10 Certification ECU (Smart Key ECU Assembly)

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (IGB VOLTAGE)
U191162E01
1.556,0.267 1.934,0.464 0.378,0.197 10 A76 2.642,0.546 3.030,0.685 0.388,0.139 10 IGB 0.052,0.044 0.365,0.183 0.314,0.139 10 *a 2,1.155 2.438,0.633 2.438,0.633 2.578,0.633 false

NOTICE:

Inspect the fuse for circuits related to this system before performing the following inspection procedure.


a.

Disconnect the millimeter wave radar sensor assembly connector.


b.

Turn the power switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A76-5 (IGB) - A76-1 (SGND) Power switch on (IG) 10 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


d.

Reconnect the millimeter wave radar sensor assembly connector.



OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
2.CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - BODY GROUND)
a.
U191163E01
1.556,0.267 1.934,0.464 0.378,0.197 10 A76 0.265,0.518 0.782,0.656 0.518,0.139 10 SGND 0.052,0.044 0.365,0.183 0.314,0.139 10 *a 1.375,1.138 0.937,0.616 0.937,0.616 0.797,0.616 false

Disconnect the millimeter wave radar sensor assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A76-1 (SGND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Millimeter Wave Radar Sensor Assembly)


c.

Reconnect the millimeter wave radar sensor assembly connector.



OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (MILLIMETER WAVE RADAR SENSOR ASSEMBLY - IG1 NO. 1 RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR