Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.11–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A05  Stop Light Switch Circuit  


DESCRIPTION

When the brake pedal is depressed, the stop light switch assembly sends a brake pedal operation signal to the driving support ECU assembly. After reception of this signal, the driving support ECU assembly cancels the radar cruise control system. When the driving support ECU assembly detects a malfunction in the stop light switch circuit, DTC C1A05 is stored.

DTC No. DTC Detection Condition Trouble Area
C1A05 Voltages of terminals ST1- and STP- of driving support ECU assembly are both below 1 V for 1 second
·

Stop light switch assembly

·

Stop light switch circuit

·

Driving support ECU assembly



WIRING DIAGRAM

A303775E62
0.281,0.406 1.177,0.802 0.896,0.396 10 false from Auxiliary Battery 0.313,0.927 1.385,1.125 1.073,0.198 10 false from IG2 Relay 2.552,0.594 3.167,0.792 0.615,0.198 10 false STOP 2.229,1.063 2.729,1.354 0.5,0.292 10 false IGN 3.156,0.313 3.313,0.51 0.156,0.198 10 false 7 3.167,0.802 3.323,1 0.156,0.198 10 false 6 3.167,1.146 3.323,1.344 0.156,0.198 10 false 2 4.125,0.417 4.281,0.615 0.156,0.198 10 false 3 4.125,0.969 4.281,1.167 0.156,0.198 10 false 5 3.344,0.427 3.5,0.625 0.156,0.198 10 false B 3.344,0.927 3.5,1.125 0.156,0.198 10 false B 3.333,1.271 3.792,1.469 0.458,0.198 10 false GND 3.917,0.552 4.073,0.75 0.156,0.198 10 false L 3.927,1.104 4.083,1.302 0.156,0.198 10 false L 5.583,0.417 5.896,0.615 0.313,0.198 10 false 27 5.583,0.969 5.896,1.167 0.313,0.198 10 false 28 5.844,0.531 6.302,0.729 0.458,0.198 10 false STP- 5.844,1.083 6.458,1.281 0.615,0.198 10 false ST1- 3.156,1.646 3.615,1.844 0.458,0.198 10 false A79 3.156,1.813 4.375,2.313 1.219,0.5 10 false Stop Light Switch Assembly 5.677,1.635 6.135,1.833 0.458,0.198 10 false L60 5.677,1.802 6.646,2.365 0.969,0.563 10 false Driving Support ECU Assembly 1.76,0.583 2.375,0.781 0.615,0.198 10 false DC/DC

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE)
a.
U190928E01
1.141,0.19 1.443,0.345 0.302,0.156 10 A79 0.909,1.864 1.309,2.020 0.400,0.156 10 GND 2.341,1.865 2.498,2.021 0.157,0.156 10 B 2.644,1.864 2.821,2.020 0.177,0.156 10 B 1.343,1.33 1.12,1.846 false 2.214,1.33 2.372,1.846 false 2.495,1.33 2.661,1.846 false 0.224,0.127 0.527,0.282 0.302,0.156 10 *a

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A79-6 (B) - Body ground Power switch on (IG) 11 to 14 V
A79-7 (B) - Body ground Always 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A79-2 (GND) - Body ground Always Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


d.

Reconnect the stop light switch assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - DRIVING SUPPORT ECU ASSEMBLY)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the driving support ECU assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A79-3 (L) - L60-27 (STP-) Always Below 1 Ω
A79-5 (L) - L60-28 (ST1-) Always Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A79-3 (L) or L60-27 (STP-) - Body ground Always 10 kΩ or higher
A79-5 (L) or L60-28 (ST1-) - Body ground Always 10 kΩ or higher



d.

Reconnect the stop light switch assembly connector.


e.

Reconnect the driving support ECU assembly connector.



OK

3.REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE STOP LIGHT SWITCH ASSEMBLY
a.

Replace the stop light switch assembly (See page Vehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>REMOVAL).



NEXT

4.CHECK FOR DTCs (C1A05)
4.CHECK FOR DTCs (C1A05)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A05 is output B




A

END (STOP LIGHT SWITCH ASSEMBLY WAS DEFECTIVE)

B

REPLACE DRIVING SUPPORT ECU ASSEMBLY