Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM › 2014.11–2015.08
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301640 DYNAMIC RADAR CRUISE CONTROL SYSTEM C

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM  C1A41  Brake Request Value Mismatch between ENG / EHV and Driving Support ECU  


DESCRIPTION

The brake booster with master cylinder (skid control ECU) receives brake control request signals from the power management control ECU and driving support ECU assembly.

When the request signals received from the power management control ECU and driving support ECU assembly are not consistent, the brake booster with master cylinder (skid control ECU) determines that a malfunction has occurred and sends a malfunction signal to the driving support ECU assembly.

DTC No. DTC Detection Condition Trouble Area
C1A41 While power switch is on (IG), brake request signal from power management control ECU and driving support ECU assembly are inconsistent for 1 second
·

Electronically controlled brake system

·

Hybrid control system

·

Power management control ECU

·

Brake booster with master cylinder (skid control ECU)

·

Driving support ECU assembly



PROCEDURE

1.CHECK FOR DTCs (ELECTRONICALLY CONTROLLED BRAKE SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Chassis / ABS/VSC/TRAC / Trouble Codes.


e.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

2.CHECK FOR DTCs (HYBRID CONTROL SYSTEM)

B

2.CHECK FOR DTCs (HYBRID CONTROL SYSTEM)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


e.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC is output B




A

3.CHECK FOR DTCs (DTC C1A41)

B

3.CHECK FOR DTCs (DTC C1A41)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A41 is output B




A

B

4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
4.REPLACE DRIVING SUPPORT ECU ASSEMBLY
a.

Replace the driving support ECU assembly (See page Engine / Hybrid System>CRUISE CONTROL>DRIVING SUPPORT ECU>REMOVAL).



NEXT

5.CHECK FOR DTCs (DTC C1A41)
5.CHECK FOR DTCs (DTC C1A41)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A41 is output B




A

END

B

6.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER
6.REPLACE BRAKE BOOSTER WITH MASTER CYLINDER
a.

Replace the brake booster with master cylinder (skid control ECU) (for LHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for LHD)>REMOVAL).


b.

Replace the brake booster with master cylinder (skid control ECU) (for RHD) (See page Brake>BRAKE SYSTEM (OTHER)>BRAKE BOOSTER (for RHD)>REMOVAL).



NEXT

7.CHECK FOR DTCs (DTC C1A41)
7.CHECK FOR DTCs (DTC C1A41)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).



d.

Perform the following to make sure that the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the malfunction cannot be detected.


i.

Drive the vehicle at a speed of between approximately 50 km/h (30 mph) and 170 km/h (105 mph).


ii.

Turn the cruise control system on using the cruise control switch (ON-OFF button).


iii.

Push the cruise control switch to -/SET to begin control of vehicle speed using the cruise control system.



e.

Enter the following menus: Powertrain / Radar Cruise / Trouble Codes.


f.

Check for DTCs.

Result:
Result Proceed to
DTC is not output A
DTC C1A41 is output B




A

END

B