The brake booster with master cylinder (skid control ECU) sends a stop light operation signal to the stop light switch assembly. When the brake booster with master cylinder (skid control ECU) detects a malfunction in the stop light circuit, the driving support ECU assembly stores DTC C1A4B.
| DTC No. | DTC Detection Condition | Trouble Area |
|---|---|---|
| C1A4B | Either of the following conditions is met:
·
When the vehicle speed is approximately 50 km/h or more, the cruise control switch (ON-OFF button) is on, the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is output, the signal is not received at terminal STP2 for 0.3 seconds or more. ·
When the vehicle speed is approximately 50 km/h or more, the cruise control switch (ON-OFF button) is on, the IG1 terminal voltage is between 11 and 14 V and the stop light illumination output signal (STPO) is not output, the signals received at terminals STP and STP2 are different for 0.3 seconds or more. |
·
Lighting system ·
Electronically controlled brake system ·
Harness or connector ·
Stop light switch assembly ·
Driving support ECU assembly |
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
When this DTC is output, malfunction in the lighting system is suspected. Check if the lighting system is functioning normally (See page Vehicle Exterior>LIGHTING (EXT)>LIGHTING SYSTEM>OPERATION CHECK).
Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.
| Condition | Illumination Condition |
|---|---|
| Brake pedal depressed | On |
| Brake pedal released | Off |
OK
NG
Turn the power switch off.
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A79-7 (B) - Body ground | Always | 11 to 14 V |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A79-2 (GND) - Body ground | Always | Below 1 Ω |
Reconnect the stop light switch assembly connector.
OK
NG
Turn the power switch off.
Disconnect the brake booster with master cylinder (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-33 (STP) - Body ground | Brake pedal depressed | 11 to 14 V |
| A58-33 (STP) - Body ground | Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder (Skid Control ECU)) |
Reconnect the brake booster with master cylinder (skid control ECU) connector.
OK
NG
Turn the power switch off.
Disconnect the stop light switch assembly connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A79-1 (OUT) - Body ground | Brake pedal depressed | 11 to 14 V |
| A79-1 (OUT) - Body ground | Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to Stop Light Switch Assembly) |
Reconnect the stop light switch assembly connector.
OK
NG
Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
Perform "Active Test" according to the display on GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay | Stop light switch assembly (STOP LP) | ON or OFF | Stop lights come on |
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
|---|---|---|---|
| Stop Light Relay Output | Stop light switch assembly (STOP LP) output/ON or OFF | ON: Relay output on (Stop light on)
OFF: Relay output off (Stop light off) |
- |
| Result | Result |
|---|---|
| Data List item changes between ON and OFF, but stop lights do not turn on | A |
| Data List item changes between ON and OFF and stop lights turn on and off | B |
A
B
Turn the power switch off.
Disconnect the brake booster with master cylinder (skid control ECU) connector.
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-3 (STPO) - A79-4 (ACC) | Always | Below 1 Ω |
| A58-3 (STPO) or A79-4 (ACC) - Body ground | Always | 10 kΩ or higher |
Reconnect the brake booster with master cylinder (skid control ECU) connector.
Reconnect the stop light switch assembly connector.
OK
NG
Turn the power switch off.
Disconnect the brake booster with master cylinder (skid control ECU) connector.
Disconnect the stop light switch assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-6 (STP2) - A79-3 (L) | Always | Below 1 Ω |
| A58-6 (STP2) or A79-3 (L) - Body ground | Always | 10 kΩ or higher |
Reconnect the brake booster with master cylinder (skid control ECU) connector.
Reconnect the stop light switch assembly connector.
OK
NG
Turn the power switch off.
Disconnect the brake booster with master cylinder (skid control ECU) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A58-6 (STP2) - Body ground | Brake pedal depressed | 11 to 14 V |
| A58-6 (STP2) - Body ground | Brake pedal released | Below 1.5 V |
| *a | Front view of wire harness connector
(to Brake Booster with Master Cylinder (Skid Control ECU)) |
Reconnect the brake booster with master cylinder (skid control ECU) connector.
OK
NG
Turn the power switch off and wait for at least 2 minutes.
Clear the DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
Make sure that the DTC detection conditions are met.
If the detection conditions are not met, the system cannot detect the malfunction.
Drive the vehicle at a speed of approximately 50 km/h or more with the cruise control switch (ON-OFF button) on.
Check for DTCs (See page Engine / Hybrid System>CRUISE CONTROL>DYNAMIC RADAR CRUISE CONTROL SYSTEM>DTC CHECK / CLEAR).
| Result | Result |
|---|---|
| DTC C1A4B is not output | A |
| DTC C1A4B is output | B |
When replacing the driving support ECU assembly, always replace it with a new one. If a driving support ECU assembly which was installed to another vehicle is used, the information stored in the driving support ECU assembly will not match the information from the vehicle. As a result, a DTC may be stored.
A
B