Home › Engine / Hybrid System › CRUISE CONTROL › LANE RECOGNITION CAMERA SENSOR › 2014.11–2017.12
RM2070E _51 Engine / Hybrid System _061914 CRUISE CONTROL _0301641 LANE RECOGNITION CAMERA SENSOR N

CRUISE CONTROL  LANE RECOGNITION CAMERA SENSOR  ADJUSTMENT  


CAUTION / NOTICE / HINT

HINT:

If the lane departure warning camera is replaced or removed and installed, perform lane departure warning camera adjustment.


PROCEDURE

Hide 86468 1.ADJUST LANE DEPARTURE WARNING CAMERA

NOTICE:
E306543E03
0.271,1.021 0.458,1.198 0.188,0.177 10 false *b 1.26,0.052 1.448,0.229 0.188,0.177 10 false *a

Text in Illustration
*a 1.5 m or more
*b 3 m or more

·

Make sure there are no black and white patterned objects in front of the vehicle.

·

Be sure to perform the measurement on a level surface that is free of obstacles and extends 1.5 m (4.92 ft.) or more in front of the vehicle.

·

Make sure that there is no wind when performing the measurement.

·

Check that there are no reflective materials in the surroundings or on the ground within a 3 m (9.84 ft.) x 3 m (9.84 ft.) area in front of the vehicle.

·

Perform the inspection in a bright area.



a.

Prepare for camera axis learning.

i.

Move the vehicle to a level surface.


ii.

Make sure the engine oil in the vehicle is at the specified level.


iii.

Make sure the engine coolant in the vehicle is at the specified level.


iv.

Make sure the fuel tank is full.


v.

w/ Spare Tire:

1.

Make sure the spare tire is in the vehicle.



vi.

Make sure the standard tools are in the vehicle.


vii.

Make sure nobody is in the vehicle.


viii.

Make sure no extra loads are in the vehicle.


ix.

Adjust the tire pressures to the specified pressure.


x.

Clean the windshield.



b.

Create a target sheet.

i.
E102781E16
2.781,1.021 2.938,1.198 0.156,0.177 10 false *c 0.958,2.354 1.115,2.531 0.156,0.177 10 false *b 0.177,2.094 0.375,2.365 0.198,0.271 10 false *a 1.281,2.792 1.438,2.969 0.156,0.177 10 false *c

Print or copy the illustration. Check that the dimensions are within +/- 5 mm (0.197 in.) of the ones in the table below.

Text in Illustration
*a 16 mm (0.630 in.)
*b 80 mm (3.15 in.)
*c 160 mm (6.30 in.)

NOTICE:
·

Make sure that the black areas of the target sheet are not glossy.

·

Make sure that the borders of the black and white areas on the target sheet are straight, and are not warped or blurry.



If the dimensions of the print or copy are not as specified, adjust settings and reprint or recopy so that the dimensions are as specified.

E144732



c.
E190544E14
0.635,1.031 1.073,1.031 false 2.292,1.083 2.729,1.083 false 0.458,0.948 0.615,1.094 0.156,0.146 10 false *b 2.76,1.01 2.917,1.156 0.156,0.146 10 false *a

Attach the target sheet.

Text in Illustration
*a Target Sheet
*b Cardboard

i.

Place the prepared target sheet on a piece of cardboard of the same size with the black area on the top right, as shown in the illustration. Then use double-sided tape to secure the target sheet in place.

NOTICE:

Do not attach reflective tape, such as transparent adhesive tape, to the target face, as this may affect target recognition.



ii.
E190545E08
1.375,1.146 0.677,1.323 false 1.156,2.25 0.75,2.719 false 1.094,2.823 1.25,2.969 0.156,0.146 10 false *b 1.167,2.135 1.385,2.333 0.219,0.198 10 false *a 1.396,1.063 1.896,1.333 0.5,0.271 10 false SST

Hang a weight with a pointed tip from the center of the target sheet. Then, with double-sided tape, attach the target sheet to the reflector so that the weight aligns with the mark-off line of SST (laser radar adjusting reflector).

SST
09870-60000  (09870-60010, 09870-60020)

Text in Illustration
*a Pointed Tip Weight
*b Mark-off Line

NOTICE:
·

Perform this procedure as accurately as possible.

·

Attach the target sheet so that it is horizontal with the ground.




iii.
E144726E17
1.115,1.667 2.031,1.667 false 0.771,1.573 1.156,1.771 0.385,0.198 10 false SST 2.667,1.865 2.844,2.031 0.177,0.167 10 false *a

Move the reflector up and down to position the center of the target at the height shown in the illustration and secure it in place.

Text in Illustration
*a 1350 mm (4.43 ft.)

SST
09870-60000  (09870-60010, 09870-60020)

NOTICE:

Perform this procedure as accurately as possible.




d.

Measure the target placement point.

NOTICE:
·

Do not place black and white patterned objects near the target.

·

Face the vehicle toward a wall with no patterns or make sure the background behind the target has no patterns.

·

Perform this procedure as accurately as possible.

·

Do not place reflective materials in the area behind the target.

·

Make sure the distance between the target and wall is within 3 m (9.84 ft.).

·

Make sure the shadow of the target is not on the wall as the camera may have a recognition error.



i.

Hang the string (with weight) from the center of the vehicle rear emblem. Mark the vehicle rear center point on the ground.

E306544E03
3.063,2.615 3.656,2.573 false 3.063,2.521 3.563,2.292 false 5.719,1.125 5.167,1.042 true 5.74,1.979 6.219,2.052 false 3.594,2.198 3.75,2.344 0.156,0.146 10 false *b 4.99,0.938 5.146,1.083 0.156,0.146 10 false *c 6.24,1.979 6.396,2.125 0.156,0.146 10 false *a 3.688,2.49 3.844,2.635 0.156,0.146 10 false *d

Text in Illustration
*a String *b Weight
*c Center point *d Point A


ii.

Repeat for the front of the vehicle.

E306545E03
1.396,1.625 2,1.719 true 3.885,2.208 3.438,2.115 false 3.896,2.302 3.354,2.396 false 1.396,1.073 2.323,0.844 true 3.25,2.021 3.406,2.167 0.156,0.146 10 false *b 2.354,0.74 2.51,0.885 0.156,0.146 10 false *c 2.031,1.646 2.188,1.792 0.156,0.146 10 true *a 3.177,2.333 3.333,2.479 0.156,0.146 10 false *d

Text in Illustration
*a String *b Weight
*c Center point *d Point B


iii.

Secure one end of a string to point A, stretch the other end so that it passes point B in a straight line, and secure the string at a position 2000 mm (6.56 ft.) or more from the front end of the vehicle.

HINT:
·

Make sure the string is taut (using tape, etc.) when it is secured.

·

Lightly flick the string with your fingers several times to confirm that the string is aligned with point B.




iv.

Mark point C at a position 643 mm (2.11 ft.) from point B.

E306546E03
6.698,2.323 6.396,1.542 false 6.438,2.448 6.708,2.875 false 2.875,2.406 2.875,2.885 false 2.635,2.396 2.635,3.167 false 2.146,2.938 2.146,3.229 false 1.979,2.896 1.979,3.354 false 2.01,2.802 1.833,2.802 false 1.479,2.417 1.479,2.885 false 0.688,2.521 0.688,2.917 false 2.01,2.031 1.75,2.031 false 2.135,1.948 2.24,1.948 false 2.115,2.135 2.208,2.135 false 2.802,2.896 2.958,3.042 0.156,0.146 10 false *b 2.573,3.188 2.729,3.333 0.156,0.146 10 false *c 6.719,2.896 6.875,3.042 0.156,0.146 10 false *a 2.063,3.198 2.281,3.365 0.219,0.167 10 false *e 1.917,3.375 2.115,3.563 0.198,0.188 10 false *f 1.396,2.896 1.583,3.083 0.188,0.188 10 false *d 2.26,1.885 2.479,2.052 0.219,0.167 10 false *h 2.24,2.073 2.438,2.26 0.198,0.188 10 false *i 1.688,2.708 1.875,2.896 0.188,0.188 10 false *g 6.25,1.438 6.469,1.604 0.219,0.167 10 false *k 0.135,2.313 0.333,2.5 0.198,0.188 10 false *l 1.625,1.927 1.813,2.115 0.188,0.188 10 false *j 2.073,0.552 2.292,0.719 0.219,0.167 10 false *n 2.635,1.333 2.823,1.521 0.188,0.188 10 false *m 0.615,2.917 0.833,3.083 0.219,0.167 10 false *k

Text in Illustration
*a Point A *b Point B
*c Point C *d Point D
*e Line E *f Line F
*g Point G (Placement Point 2) *h Line H
*i Line I *j Point J (Placement Point 3)
*k Tape *l String
*m 643 mm (2.11 ft.) *n 1893 mm (6.21 ft.)


v.

Mark point D at a position 1893 mm (6.21 ft.) from point B.


vi.

Using a string, mark line E at a position 1000 mm (3.28 ft.) from point C.


vii.

Using a string, mark line H at a position 1000 mm (3.28 ft.) from point C.


viii.

Using a string, mark line F at a position 1000 mm (3.28 ft.) from point D.


ix.

Using a string, mark line I at a position 1000 mm (3.28 ft.) from point D.


x.

Mark point G at the point where line E and line F intersect (placement point 2).


xi.

Mark point J at the point where line H and line I intersect (placement point 3).


xii.

Secure a string that connects point G and point J to the ground (target placement line).

E306547E02
6.698,2.51 6.698,3.271 false 6.406,2.438 6.406,3.271 false 2.865,2.417 2.865,3.448 false 2.635,2.417 2.635,3.448 false 2.146,1.729 2.26,1.729 false 2.094,2.031 2.25,2.031 false 2.083,2.427 2.208,2.531 false 2.104,2.802 2.229,2.802 false 2.146,3.25 2.271,3.25 false 2.052,3 1.656,3.031 false 1.469,2.438 1.469,2.698 false 0.698,2.521 0.698,2.719 false 2.802,3.479 3.031,3.646 0.229,0.167 10 false *b 2.563,3.479 2.771,3.656 0.208,0.177 10 false *c 6.323,3.26 6.552,3.438 0.229,0.177 10 false *a 0.125,2.313 0.354,2.479 0.229,0.167 10 false *e 6.646,3.302 6.854,3.479 0.208,0.177 10 false *f 1.385,2.719 1.615,2.896 0.229,0.177 10 false *d 2.656,1.323 2.885,1.49 0.229,0.167 10 false *h 2.375,0.927 2.583,1.104 0.208,0.177 10 false *i 2.24,2.708 2.469,2.885 0.229,0.177 10 false *g 2.229,2.479 2.458,2.646 0.229,0.167 10 false *k 2.104,0.51 2.313,0.688 0.208,0.177 10 false *l 2.292,1.948 2.521,2.125 0.229,0.177 10 false *j 1.448,2.958 1.677,3.135 0.229,0.177 10 false *m 0.635,2.74 0.844,2.917 0.208,0.177 10 false *f 2.292,3.167 2.5,3.344 0.208,0.177 10 false *f 2.281,1.646 2.49,1.823 0.208,0.177 10 false *f 1.969,3.448 2.198,3.615 0.229,0.167 10 false *e

Text in Illustration
*a Point A *b Point B
*c Point C *d Point D
*e String *f Tape
*g Point G (Placement Point 2) *h 643 mm (2.11 ft.)
*i 1268 mm (4.16 ft.) *j Point J (Placement Point 3)
*k Point K (Placement Point 1) *l 1893 mm (6.21 ft.)
*m Target Placement Line - -


xiii.

Mark point K at the intersection between the string connecting points C and D and the string connecting points G and J (placement point 1).


xiv.

Confirm the distance measurements for points K, G, and J (placement points 1, 2, and 3) again.

E306594E01
3.361,3.224 3.574,3.373 0.213,0.149 10 *b 3.018,3.319 3.263,3.468 0.245,0.149 10 *c 6.343,3.296 6.549,3.445 0.206,0.149 10 *a 2.366,3.094 2.580,3.243 0.213,0.149 10 *e 1.542,2.954 1.787,3.103 0.245,0.149 10 *f 1.107,2.576 1.313,2.725 0.206,0.149 10 *d 2.307,1.834 2.521,1.983 0.213,0.149 10 *h 1.631,1.766 1.876,1.915 0.245,0.149 10 *i 1.535,2.707 1.742,2.856 0.206,0.149 10 *g 1.746,2.478 1.960,2.627 0.213,0.149 10 *k 1.654,3.188 1.898,3.337 0.245,0.149 10 *l 1.677,1.936 1.883,2.085 0.206,0.149 10 *j 2.457,2.758 2.671,2.907 0.213,0.149 10 *n 4.957,2.403 5.202,2.552 0.245,0.149 10 *o 1.95,3.491 2.156,3.640 0.206,0.149 10 *m 2.11,0.712 2.323,0.861 0.213,0.149 10 *q 2.4,1.067 2.644,1.216 0.245,0.149 10 *r 3.076,0.391 3.282,0.540 0.206,0.149 10 *p 3.73,2.694 3.974,2.843 0.245,0.149 10 *t 2.667,1.562 2.874,1.711 0.206,0.149 10 *s 1.65,1.559 1.895,1.708 0.245,0.149 10 *l 0.629,2.644 0.874,2.793 0.245,0.149 10 *l 6.645,3.102 6.890,3.251 0.245,0.149 10 *l 6.71,2.507 6.71,3.085 false 6.416,2.439 6.416,3.284 false 4.182,2.57 3.873,2.762 false 2.896,2.44 3.373,3.207 false 2.649,2.445 3.025,3.29 false 2.352,2.596 2.452,2.758 false 2.15,2.908 2.33,3.089 false 1.959,3.253 1.79,3.253 false 1.972,2.897 1.714,3.026 false 2.017,2.801 1.722,2.801 false 2.036,2.436 1.919,2.546 false 2.149,1.903 2.282,1.903 false 2.018,2.009 1.815,2.009 false 1.957,1.896 1.761,1.846 false 1.957,1.634 1.769,1.634 false 1.446,2.438 1.28,2.624 false 0.698,2.507 0.698,2.629 false 0.105,2.318 0.311,2.466 0.206,0.149 10 *m

Text in Illustration
*a Point A *b Point B
*c Point C *d Point D
*e Line E *f Line F
*g Point G (Placement Point 2) *h Line H
*i Line I *j Point J (Placement Point 3)
*k Point K (Placement Point 1) *l Tape
*m String *n 1000 mm (3.28 ft.) (String)
*o 75 mm (2.95 in.) *p 3000 mm (9.84 ft.)
*q 1893 mm (6.21 ft.) *r 1268 mm (4.16 ft.)
*s 643 mm (2.11 ft.) *t Lane Departure Warning Camera Position



e.

Memorize camera/target position.

NOTICE:
·

Close all doors.

·

Perform the procedure with no one in the vehicle.

·

During the procedure, do not lean on the vehicle.

·

Do not turn on the headlights.



i.

When using the GTS:

1.

Connect the GTS to the DLC3.

2.

Turn the power switch on (IG).*1

3.

Turn the GTS on.

4.

Select "Connect to Vehicle".

5.

Select each item on the display screen and proceed to the next screen.

6.

Under "System Selection Menu", select "Lane Departure Alert".

7.

Select "Utility" from the display screen.

8.

Select "Recognition Camera/Target Position Memory" and proceed to the next screen.

HINT:

A buzzer will sound for 1 second.


9.

Follow the GTS display, and continue with the adjustment.



ii.

Input the height of the camera "1361 mm (53.6 in.)" and the horizontal position of the camera "-75 mm (-2.95 in.)" into the input screen. Then press the "Next" button on the display screen.


iii.

Input "3000 mm (118 in.)" for the distance from the camera to the target and "1350 mm (53.1 in.)" for the height of the target into the input screen. Then press the "Next" button on the display screen.


iv.

Input "1775 mm (69.9 in.)" for the width of the vehicle and "781 mm (30.7 in.)" for the distance between the recognition camera and the front tire into the input screen. Then press the "Next" button on the display screen.


v.

Press the "Exit" button to finish the camera/target position memory mode.

NOTICE:

If "Error Camera/target position memory" is displayed on the screen, press the "Try Again" button, and repeat from procedure *1 again.




f.

Perform camera axis learning.

i.

Select "Connect to Vehicle".


ii.

Select each item on the display screen and proceed to the next screen.


iii.

Under "System Selection Menu", select "Lane Departure Alert".*1


iv.

Select "Utility" from the display screen.


v.

Select "Recognition Camera Axis Adjust" from the display screen.


vi.

Follow the GTS display and continue with the adjustment.


vii.
E190547E08
1.396,0.75 0.813,1.427 false 1.438,0.635 1.833,0.938 0.396,0.302 10 false SST 1.646,2.594 1.844,2.781 0.198,0.188 10 false *b 0.938,2.948 1.135,3.135 0.198,0.188 10 false *c 1.375,2.042 1.552,2.208 0.177,0.167 10 false *a

Align the target sheet with the target placement line and align the mark-off line with point K (placement point 1).

Text in Illustration
*a Mark-off Line
*b Point K (Placement Point 1)
*c Target Placement Line


viii.

Check that the screen displays camera axis learning for target 1, then press the "Next" button on the display screen.


ix.
E190547E08
1.396,0.75 0.813,1.427 false 1.438,0.635 1.833,0.938 0.396,0.302 10 false SST 1.646,2.594 1.844,2.781 0.198,0.188 10 false *b 0.938,2.948 1.135,3.135 0.198,0.188 10 false *c 1.375,2.042 1.552,2.208 0.177,0.167 10 false *a

Align the target sheet with the target placement line, and align the mark-off line with point G (placement point 2).

Text in Illustration
*a Mark-off Line
*b Point G (Placement Point 2)
*c Target Placement Line


x.

Check that the screen displays camera axis learning for target 2, then press the "Next" button on the display screen.

NOTICE:

Within 3 minutes after the screen displays the camera axis learning for target 2, move the target and press the "Next" button on the display screen.



xi.
E190547E08
1.396,0.75 0.813,1.427 false 1.438,0.635 1.833,0.938 0.396,0.302 10 false SST 1.646,2.594 1.844,2.781 0.198,0.188 10 false *b 0.938,2.948 1.135,3.135 0.198,0.188 10 false *c 1.375,2.042 1.552,2.208 0.177,0.167 10 false *a

Align the target sheet with the target placement line and align the mark-off line with point J (placement point 3).

Text in Illustration
*a Mark-off Line
*b Point J (Placement Point 3)
*c Target Placement Line


xii.

Check that the screen displays camera axis learning for target 3 then press the "Next" button on the display screen.

NOTICE:

Within 3 minutes after the screen displays the camera axis learning for target 3, move the target and press the "Next" button on the display screen.



xiii.

Press the "Exit" button to finish camera axis learning mode.

NOTICE:
If "Error camera axis adjust" is displayed on the screen, press the "Exit" button. Then after checking the following, turn the power switch on (IG) and off, and repeat from procedure *1 again.
·

Height of the target.

·

Distance from the lane departure warning camera to the target.

·

Orientation of the target (black area positioned on top right).

·

If surrounding area is bright enough.

·

If black and white patterned objects are placed near the target.