Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › from 2016.05
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM C

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  C2301  Shift Changing Time Malfunction  


DESCRIPTION

The transmission control ECU assembly receives a P position switch signal from the hybrid vehicle control ECU and then activates the shift control actuator assembly. At the same time, the transmission control ECU assembly detects the length of time it takes for the parking lock mechanism to switch. The transmission control ECU assembly stores this DTC when this length of time is longer than specified.

DTC No. DTC Detection Condition Trouble Area
C2301 A shift control actuator assembly (parking lock motor) internal malfunction (parking lock motor spins freely) is detected for 2 seconds or more.
·

Auxiliary battery

·

Shift control actuator assembly

·

Hybrid vehicle transaxle assembly

·

Transmission control ECU assembly



WIRING DIAGRAM

C243983E04
1.531,0.865 1.865,1.031 0.333,0.167 10 false BMA 1.917,0.792 2.104,0.958 0.188,0.167 10 false 23 5.771,0.771 5.865,0.938 0.094,0.167 10 false 1 4.948,1.688 5.771,1.854 0.823,0.167 10 false P CON MTR 4.833,0.781 4.927,0.948 0.094,0.167 10 false 2 5.781,1.281 5.875,1.448 0.094,0.167 10 false 3 4.833,1.271 4.927,1.438 0.094,0.167 10 false 5 1.958,1.635 2.063,1.802 0.104,0.167 10 false 5 1.958,2 2.063,2.167 0.104,0.167 10 false 2 1.958,2.333 2.063,2.5 0.104,0.167 10 false 1 2.5,1.625 2.604,1.792 0.104,0.167 10 false 1 2.5,1.99 2.604,2.156 0.104,0.167 10 false 6 4.271,2 4.375,2.167 0.104,0.167 10 false 2 2.5,2.323 2.604,2.49 0.104,0.167 10 false 7 1.542,1.708 1.875,1.875 0.333,0.167 10 false MUA 1.531,2.073 1.865,2.24 0.333,0.167 10 false MVA 1.5,2.427 1.865,2.594 0.365,0.167 10 false MWA 2.844,1.625 3.177,1.792 0.333,0.167 10 false MUA 2.844,1.99 3.177,2.156 0.333,0.167 10 false MVA 3.75,2.01 4.083,2.177 0.333,0.167 10 false BMA 2.844,2.333 3.208,2.5 0.365,0.167 10 false MWA 0.542,3.615 0.906,3.781 0.365,0.167 10 false A23 0.542,3.771 1.865,4.198 1.323,0.427 10 false Transmission Control ECU Assembly 2.771,3.615 3.135,3.781 0.365,0.167 10 false D2 2.771,3.792 4.146,4.177 1.375,0.385 10 false Shift Control Actuator Assembly 6.063,1.531 6.885,1.698 0.823,0.167 10 false P CON MTR

CAUTION / NOTICE / HINT

NOTICE:
·

Do not remove/install the auxiliary battery or disconnect the cable from the negative (-) auxiliary battery terminal before instructed.

·

It may not be possible to clear the following DTCs using the GTS: DTC C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). In such cases, disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs after the repair.

·

After turning the power switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) auxiliary battery terminal notices before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).



PROCEDURE

1.CHECK FREEZE FRAME DATA
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


d.

Read the freeze frame data of DTC C2301.

Result:
Result Proceed to
IG (+B) voltage is 9 V or more A
IG (+B) voltage is less than 9 V B



e.

Turn the power switch off.



A

2.CLEAR DTC

B

7.CLEAR DTC
3.CHARGE AUXILIARY BATTERY
a.

Charge the auxiliary battery.



NEXT

4.CHECK DTC OUTPUT (SIMULATION TEST)
4.CHECK DTC OUTPUT (SIMULATION TEST)
a.

Connect the GTS to the DLC3.


b.

Release the brake pedal and turn the power switch on (IG).

HINT:

Do not turn the power switch on (READY).



c.

Depress the brake pedal and move the shift lever to select neutral (N).


d.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


e.

Check if DTCs are output.

Result:
Result Proceed to
DTC C2301 is output A
DTC C2301 is not output. B



f.

Turn the power switch off.



A

5.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

B

END (AUXILIARY BATTERY WAS INSUFFICIENTLY CHARGED)

5.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY

OK

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY

NG

6.CHECK HYBRID VEHICLE TRANSAXLE ASSEMBLY

OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

8.INSPECT AUXILIARY BATTERY
a.

Inspect the auxiliary battery (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>CHARGING SYSTEM>ON-VEHICLE INSPECTION).

Result:
Result Proceed to
Charge or replace the auxiliary battery. A
The auxiliary battery voltage is normal. B




A

9.CHARGE OR REPLACE AUXILIARY BATTERY

B

3.CHARGE AUXILIARY BATTERY
9.CHARGE OR REPLACE AUXILIARY BATTERY
a.

Charge or replace the auxiliary battery (See page Power Source / Network>2ZR-FXE (BATTERY / CHARGING)>AUXILIARY BATTERY>COMPONENTS).



NEXT

4.CHECK DTC OUTPUT (SIMULATION TEST)