Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › 2014.11–2016.05
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM J

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  "P" Position Switch Indicator Light Circuit  


DESCRIPTION

The indicator light comes on when the P position switch (transmission shift main switch) is pressed (park (P) selected), goes off when a shift state other than park (P) is selected and goes off when a system malfunction occurs. If a malfunction occurs, a parking lock system warning message will be displayed on the combination meter sub-assembly (w/o Multi-information Display) or a malfunction warning message will be displayed on the multi-information display (w/ Multi-information Display) and the parking lock system warning light (w/o Multi-information Display) or master warning light (w/ Multi-information Display) will come on.

WIRING DIAGRAM

C239009E11
0.51,0.698 1.448,0.875 0.938,0.177 10 false P CON MAIN 5.01,1.333 5.302,1.521 0.292,0.188 10 false IND 2.469,2.865 2.719,3.052 0.25,0.188 10 false P1 2.25,2.771 2.438,2.958 0.188,0.188 10 false 16 4.771,1.24 4.979,1.427 0.208,0.188 10 false 20 3.417,0.833 3.531,0.99 0.115,0.156 10 false 6 3.427,1.25 3.542,1.406 0.115,0.156 10 false 7 2.313,1.24 2.427,1.396 0.115,0.156 10 false 2 2.313,0.844 2.427,1 0.115,0.156 10 false 4 2.479,0.917 2.646,1.073 0.167,0.156 10 false S 2.479,1.313 2.646,1.49 0.167,0.177 10 false E 3.042,0.917 3.417,1.115 0.375,0.198 10 false IND+ 3.083,1.302 3.427,1.479 0.344,0.177 10 false IND- 2.438,3.625 4.552,3.844 2.115,0.219 10 false Power Management Control ECU 2.438,3.448 2.802,3.635 0.365,0.188 10 false L5 2.417,1.635 2.833,1.802 0.417,0.167 10 false L124 2.417,1.802 4.51,2.448 2.094,0.646 10 false P Position Switch (Transmission Shift Main Switch) 4.958,3.469 5.271,3.646 0.313,0.177 10 false A23 4.958,3.646 6.656,4.01 1.698,0.365 10 false Transmission Control ECU Assembly

PROCEDURE

1.CHECK P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) (INDICATOR LIGHT)
a.

Turn the power switch on (IG).


b.

Depress the brake pedal and move the shift lever to select neutral (N).


c.

Inspect the indicator light condition by operating the P position switch (transmission shift main switch).

Result:
Condition of Indicator Light Proceed to
Indicator light does not go off. (Remains on) A
Indicator light does not come on. B



d.

Turn the power switch off.



A

2.CHECK P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) (INDICATOR LIGHT)

B

4.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) POWER SOURCE CIRCUIT)
2.CHECK P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) (INDICATOR LIGHT)
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Turn the power switch on (IG).


c.

Inspect the indicator light condition by operating the P position switch (transmission shift main switch).

Result:
Condition of Indicator Light Proceed to
Indicator light does not go off. (Remains on) A
Indicator light goes off. B


NOTICE:

Turning the power switch on (IG) with the transmission control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.



d.

Turn the power switch off.


e.

Connect the A23 transmission control ECU assembly connector.



A

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))

B

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Disconnect the L124 P position switch (transmission shift main switch) connector.


c.
U154761E02
1.552,1.625 0.76,1.396 true 2.083,3.885 2.688,3.281 true 0.125,0.177 0.406,0.365 0.281,0.188 10 false *a 0.125,3.031 0.406,3.219 0.281,0.188 10 false *b 2.729,3.188 3.083,3.365 0.354,0.177 10 false IND- 0.458,1.302 0.76,1.479 0.302,0.177 10 false IND 1.625,0.344 1.917,0.51 0.292,0.167 10 false A23 1.573,3.031 1.906,3.198 0.333,0.167 10 false L124

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-20 (IND) or L124-7 (IND-) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


d.

Connect the L124 P position switch (transmission shift main switch) connector.


e.

Connect the A23 transmission control ECU assembly connector.



OK

REPLACE P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK HARNESS AND CONNECTOR (P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH) POWER SOURCE CIRCUIT)
a.

Disconnect the L124 P position switch (transmission shift main switch) connector.


b.
U154746E03
1.948,1.313 2.365,1.729 true 0.188,0.094 0.469,0.281 0.281,0.188 10 false *a 2.354,1.729 2.708,1.906 0.354,0.177 10 false IND+ 1.583,0.271 1.958,0.438 0.375,0.167 10 false L124

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
L124-6 (IND+) - Body ground Power switch off 9 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


c.

Connect the L124 P position switch (transmission shift main switch) connector.



OK

5.INSPECT P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

NG

CHECK AND REPAIR POWER SOURCE CIRCUIT

5.INSPECT P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)
a.

Disconnect the L124 P position switch (transmission shift main switch) connector.


b.
U154315E03
1.385,1.198 1.135,1.635 true 1.542,1.198 1.844,1.625 true 2.271,1.073 2.125,1.25 false 1.281,1.073 1.146,1.25 false 0.135,0.073 0.417,0.26 0.281,0.188 10 false *a 0.969,1.635 1.323,1.813 0.354,0.177 10 false IND- 1.771,1.635 2.125,1.813 0.354,0.177 10 false IND+ 1.573,0.323 1.948,0.49 0.375,0.167 10 false L124

Apply auxiliary battery voltage between terminals L124-6 (IND+) and L124-7 (IND-) and check the indicator light.

Result:
Condition Specified Condition
Auxiliary battery voltage applied between terminals L124-6 (IND+) and L124-7 (IND-) Comes on


Text in Illustration
*a Component without harness connected
(P Position Switch (Transmission Shift Main Switch))

HINT:

Terminals No. 1 and No. 8 on the component side connector are empty.



c.

Connect the L124 P position switch (transmission shift main switch) connector.



OK

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))

NG

REPLACE P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH)

6.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P POSITION SWITCH (TRANSMISSION SHIFT MAIN SWITCH))
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Disconnect the L124 P position switch (transmission shift main switch) connector.


c.
U154761E02
1.552,1.625 0.76,1.396 true 2.083,3.885 2.688,3.281 true 0.125,0.177 0.406,0.365 0.281,0.188 10 false *a 0.125,3.031 0.406,3.219 0.281,0.188 10 false *b 2.729,3.188 3.083,3.365 0.354,0.177 10 false IND- 0.458,1.302 0.76,1.479 0.302,0.177 10 false IND 1.625,0.344 1.917,0.51 0.292,0.167 10 false A23 1.573,3.031 1.906,3.198 0.333,0.167 10 false L124

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A23-20 (IND) - L124-7 (IND-) Power switch off Below 1 Ω


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch))


d.

Connect the L124 P position switch (transmission shift main switch) connector.


e.

Connect the A23 transmission control ECU assembly connector.



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR