The indicator light comes on when the P position switch (transmission shift main switch) is pressed (park (P) selected), goes off when a shift state other than park (P) is selected and goes off when a system malfunction occurs. If a malfunction occurs, a parking lock system warning message will be displayed on the combination meter sub-assembly (w/o Multi-information Display) or a malfunction warning message will be displayed on the multi-information display (w/ Multi-information Display) and the parking lock system warning light (w/o Multi-information Display) or master warning light (w/ Multi-information Display) will come on.
Turn the power switch on (IG).
Depress the brake pedal and move the shift lever to select neutral (N).
Inspect the indicator light condition by operating the P position switch (transmission shift main switch).
| Condition of Indicator Light | Proceed to |
|---|---|
| Indicator light does not go off. (Remains on) | A |
| Indicator light does not come on. | B |
Turn the power switch off.
A
B
Disconnect the A23 transmission control ECU assembly connector.
Turn the power switch on (IG).
Inspect the indicator light condition by operating the P position switch (transmission shift main switch).
| Condition of Indicator Light | Proceed to |
|---|---|
| Indicator light does not go off. (Remains on) | A |
| Indicator light goes off. | B |
Turning the power switch on (IG) with the transmission control ECU assembly connector disconnected causes other DTCs to be stored. Clear the DTCs after performing this inspection.
Turn the power switch off.
Connect the A23 transmission control ECU assembly connector.
A
B
Disconnect the A23 transmission control ECU assembly connector.
Disconnect the L124 P position switch (transmission shift main switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-20 (IND) or L124-7 (IND-) - Body ground and other terminals | Power switch off | 10 kΩ or higher |
| *a | Front view of wire harness connector
(to Transmission Control ECU Assembly) |
| *b | Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch)) |
Connect the L124 P position switch (transmission shift main switch) connector.
Connect the A23 transmission control ECU assembly connector.
OK
NG
Disconnect the L124 P position switch (transmission shift main switch) connector.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L124-6 (IND+) - Body ground | Power switch off | 9 to 14 V |
| *a | Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch)) |
Connect the L124 P position switch (transmission shift main switch) connector.
OK
NG
Disconnect the L124 P position switch (transmission shift main switch) connector.
Apply auxiliary battery voltage between terminals L124-6 (IND+) and L124-7 (IND-) and check the indicator light.
| Condition | Specified Condition |
|---|---|
| Auxiliary battery voltage applied between terminals L124-6 (IND+) and L124-7 (IND-) | Comes on |
| *a | Component without harness connected
(P Position Switch (Transmission Shift Main Switch)) |
Terminals No. 1 and No. 8 on the component side connector are empty.
Connect the L124 P position switch (transmission shift main switch) connector.
OK
NG
Disconnect the A23 transmission control ECU assembly connector.
Disconnect the L124 P position switch (transmission shift main switch) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| A23-20 (IND) - L124-7 (IND-) | Power switch off | Below 1 Ω |
| *a | Front view of wire harness connector
(to Transmission Control ECU Assembly) |
| *b | Front view of wire harness connector
(to P Position Switch (Transmission Shift Main Switch)) |
Connect the L124 P position switch (transmission shift main switch) connector.
Connect the A23 transmission control ECU assembly connector.
OK
NG