Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › 2015.08–2016.05
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM C

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  C2303  Short in Power Source Relay Circuit  


DESCRIPTION

The P CON MTR relay (transaxle parking lock control relay) is activated by output voltage from the transmission control ECU assembly and supplies power to the shift control actuator assembly (parking lock motor). The transmission control ECU assembly stores this DTC when it detects a malfunction in the P CON MTR relay (transaxle parking lock control relay).

DTC No. DTC Detection Condition Trouble Area
C2303 When the P CON MTR relay (transaxle parking lock control relay) is off, voltage of transmission control ECU assembly terminal MUA, MVA and MWA are 6 V or more for 0.064 seconds or more.
·

Transmission control ECU assembly

·

P CON MTR relay (Transaxle parking lock control relay)

·

Wire harness or connector



WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

It may not be possible to clear the following DTCs using the GTS: DTC C2300 (Actuator System Malfunction), C2301 (Shift Changing Time Malfunction), C2303 (Short in Power Source Relay Circuit), C2304 (Open or Short Circuit in U Phase), C2305 (Open or Short Circuit in V Phase), C2306 (Open or Short Circuit in W Phase), C2307 (Power Supply) and C2309 (Open in B+ Circuit). In such cases, disconnect the P CON MAIN fuse and wait for at least 60 seconds to clear the DTCs after the repair.


PROCEDURE

1.CHECK SHIFT CONTROL ACTUATOR ASSEMBLY (SHIFT CONTROL ACTUATOR ASSEMBLY POWER SOURCE CIRCUIT)
a.

Disconnect the D2 shift control actuator assembly connector.


b.
U111055E02
1.594,0.938 2.458,0.458 true 0.115,0.125 0.396,0.313 0.281,0.188 10 false *a 2.5,0.354 2.854,0.531 0.354,0.177 10 false BMA 1.604,0.177 1.969,0.344 0.365,0.167 10 false D2

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D2-2 (BMA) - Body ground Power switch off Below 1 V


Text in Illustration
*a Front view of wire harness connector
(to Shift Control Actuator Assembly)


c.

Connect the D2 shift control actuator assembly connector.



OK

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR ASSEMBLY)

NG

3.INSPECT P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - SHIFT CONTROL ACTUATOR ASSEMBLY)
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Disconnect the D2 shift control actuator assembly connector.


c.
U154759E03
1.25,1.135 0.833,1.135 true 1.417,1.073 0.854,0.438 true 1.99,1.073 2.656,0.406 true 1.344,3.458 0.802,2.854 true 1.396,3.781 0.927,4.24 true 1.594,3.771 2.063,4.25 true 0.104,0.135 0.385,0.323 0.281,0.188 10 false *a 0.104,2.438 0.385,2.625 0.281,0.188 10 false *b 0.427,1.063 0.802,1.24 0.375,0.177 10 false MWA 2.708,0.281 3.083,0.458 0.375,0.177 10 false MUA 0.531,0.25 0.906,0.427 0.375,0.177 10 false MVA 1.958,4.271 2.333,4.448 0.375,0.177 10 false MWA 0.448,2.708 0.823,2.885 0.375,0.177 10 false MUA 0.583,4.167 0.958,4.344 0.375,0.177 10 false MVA 1.646,0.219 1.938,0.385 0.292,0.167 10 false A23 1.688,2.615 2.052,2.781 0.365,0.167 10 false D2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-5 (MUA) or D2-1 (MUA) - Body ground and other terminals Power switch off 10 kΩ or higher
A23-2 (MVA) or D2-6 (MVA) - Body ground and other terminals Power switch off 10 kΩ or higher
A23-1 (MWA) or D2-7 (MWA) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b Front view of wire harness connector
(to Shift Control Actuator Assembly)


d.

Connect the D2 shift control actuator assembly connector.


e.

Connect the A23 transmission control ECU assembly connector.



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)
a.
C225994E06
2.01,0.688 1.719,0.615 false 2.656,0.698 2.917,0.615 false 2.531,1.115 2.917,1.021 false 2.531,1.615 2.938,1.5 false 0.219,0.771 0.385,0.948 0.167,0.177 10 false 3 1.229,0.76 1.375,0.969 0.146,0.208 10 false 5 0.208,1.302 0.375,1.469 0.167,0.167 10 false 1 1.208,1.292 1.385,1.469 0.177,0.177 10 false 2 1.583,0.51 1.75,0.677 0.167,0.167 10 false 1 2.99,0.49 3.167,0.667 0.177,0.177 10 false 2 2.99,0.927 3.135,1.135 0.146,0.208 10 false 5 3,1.396 3.156,1.573 0.156,0.177 10 false 3

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
3 - 5 Auxiliary battery voltage is not applied between terminals 1 and 2 10 kΩ or higher
Auxiliary battery voltage is applied between terminals 1 and 2 Below 1 Ω



c.

Reinstall the P CON MTR relay (transaxle parking lock control relay).



OK

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MTR RELAY)

NG

REPLACE P CON MTR RELAY (TRANSAXLE PARKING LOCK CONTROL RELAY)

4.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MTR RELAY)
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


c.
U154739E02
2.104,1.427 2.104,1.844 true 0.094,0.083 0.375,0.271 0.281,0.188 10 false *a 1.958,1.854 2.313,2.031 0.354,0.177 10 false BMA 1.594,0.25 1.885,0.417 0.292,0.167 10 false A23

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-23 (BMA) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)


d.

Reinstall the P CON MTR relay (transaxle parking lock control relay).


e.

Connect the A23 transmission control ECU assembly connector.



OK

5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P CON MTR RELAY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (SHIFT CONTROL ACTUATOR ASSEMBLY - P CON MTR RELAY)
a.

Disconnect the D2 shift control actuator assembly connector.


b.

Remove the P CON MTR relay (transaxle parking lock control relay) from the engine room relay block and junction block assembly.


c.
U111056E02
1.594,0.938 2.458,0.458 true 0.115,0.125 0.396,0.313 0.281,0.188 10 false *a 2.5,0.354 2.854,0.531 0.354,0.177 10 false BMA 1.604,0.177 1.969,0.344 0.365,0.167 10 false D2

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
D2-2 (BMA) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Shift Control Actuator Assembly)


d.

Reinstall the P CON MTR relay (transaxle parking lock control relay).


e.

Connect the D2 shift control actuator assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR