Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM C

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  C2310  Open or Short Circuit in Battery Circuit  


DESCRIPTION

Auxiliary battery voltage is constantly applied to terminal BATT. This voltage is used to power the transmission control ECU assembly memory. The transmission control ECU assembly stores this DTC when it detects a malfunction related to terminal BATT.

HINT:

When there is an open or short in the BATT circuit, information on the actuator position (park (P) selected or a shift state other than park (P) selected) stored in the transmission control ECU assembly is cleared every time the power switch is turned off. Therefore, the ECU works to recognize the position each time the power switch is turned on (IG). As a result, the time from when the power switch is turned on (IG) until "READY" is indicated may become longer than normal.


DTC No. DTC Detection Condition Trouble Area
C2310 With the power switch on (IG) (IG circuit malfunction is not detected), voltage of transmission control ECU assembly terminal BATT is 8 V or less for 1 second or more.
·

P CON MAIN fuse

·

Transmission control ECU assembly

·

Wire harness or connector



WIRING DIAGRAM

C351656E01
1.375,2.208 2.729,2.542 1.354,0.333 10 false Auxiliary Battery 1.271,1.406 1.833,1.677 0.563,0.271 10 false MAIIN 2.51,1.104 3.521,1.375 1.01,0.271 10 false P CON MAIN 2.563,0.844 2.906,1.115 0.344,0.271 10 false 1 3,0.833 3.344,1.104 0.344,0.271 10 false 2 4.302,0.813 4.646,1.083 0.344,0.271 10 false 15 4.563,0.958 5.073,1.281 0.51,0.323 10 false BATT 4.094,2.458 4.438,2.729 0.344,0.271 10 false A23 4.094,2.615 6.667,3.031 2.573,0.417 10 false Transmission Control ECU Assembly

PROCEDURE

1.INSPECT FUSE (P CON MAIN)
a.

Remove the P CON MAIN fuse from the engine room relay block and junction block assembly.


b.
C226012E02
0.158,0.135 0.350,0.337 0.193,0.202 10 *1 2.827,1.005 3.020,1.171 0.193,0.165 10 *2 1.779,1.331 2.806,1.108 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
P CON MAIN fuse Always Below 1 Ω


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*2 P CON MAIN Fuse


c.

Install the P CON MAIN fuse.



OK

2.READ VALUE USING GTS (BATTERY VOLTAGE VALUE)

NG

REPLACE FUSE (P CON MAIN)

2.READ VALUE USING GTS (BATTERY VOLTAGE VALUE)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Transmission Control / Data List / Battery Voltage Value.


d.

Read the Data List displayed on the GTS.

Result:
Tester Display Condition Specified Condition
Battery Voltage Value Always 9 to 14 V



e.

Turn the power switch off.



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MAIN FUSE)
3.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - P CON MAIN FUSE)
a.

Disconnect the A23 transmission control ECU assembly connector.


b.

Disconnect the P CON MAIN fuse from the engine room relay block and junction block assembly.


c.
U154794E02
2.125,1.219 2.385,0.844 false 0.177,0.104 0.438,0.344 0.26,0.24 10 false *a 0.177,1.969 0.417,2.26 0.24,0.292 10 false *1 2.021,2.448 2.229,2.646 0.208,0.198 10 false *b 2.427,0.719 2.844,0.875 0.417,0.156 10 false BATT 1.563,0.219 1.885,0.385 0.323,0.167 10 false A23

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A23-15 (BATT) - 2 (P CON MAIN fuse) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A23-15 (BATT) or 2 (P CON MAIN fuse) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*1 Engine Room Relay Block and Junction Block Assembly
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b P CON MAIN Fuse Connector of Engine Room Relay Block and Junction Block Assembly

NOTICE:

Be careful not to break the fuse holder by forcing the tester probes into it during this inspection.



d.

Install the P CON MAIN fuse.


e.

Connect the A23 transmission control ECU assembly connector.



OK

CHECK AND REPAIR POWER SOURCE CIRCUIT

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR