Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › 2012.03–2016.05
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM C

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  C2311  Communication Error from HV ECU  


DESCRIPTION

The transmission control ECU assembly receives a P position switch signal from the power management control ECU and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. The transmission control ECU assembly stores this DTC when it detects a communication error between the power management control ECU and the transmission control ECU assembly.

DTC No. DTC Detection Condition Trouble Area
C2311 With the power switch on (IG) (IG circuit malfunction is not detected), a signal cannot be received from the power management control ECU (open or short in the PCON terminal circuit) or a pulse signal malfunction is received from the power management control ECU for 2 seconds or more.
·

Transmission control ECU assembly

·

Power management control ECU

·

Wire harness or connector



WIRING DIAGRAM

C239007E09
1.115,1.802 1.427,1.99 0.313,0.188 10 false A22 1.115,1.969 3.24,2.156 2.125,0.188 10 false Power Management Control ECU 2.156,0.792 2.604,0.969 0.448,0.177 10 false PCON 2.604,0.688 2.813,0.865 0.208,0.177 10 false 22 4.667,0.802 5.115,0.979 0.448,0.177 10 false PCON 4.469,0.698 4.677,0.875 0.208,0.177 10 false 22 4.188,1.771 4.49,1.958 0.302,0.188 10 false A24 4.188,1.927 6.604,2.302 2.417,0.375 10 false Transmission Control ECU Assembly 4.677,1.313 5.125,1.49 0.448,0.177 10 false E1 4.531,1.208 4.688,1.385 0.156,0.177 10 false 1

PROCEDURE

1.CHECK TRANSMISSION CONTROL ECU ASSEMBLY
a.

Turn the power switch on (IG).


b.
U154838E02
2.604,1.438 2.792,2.323 true 2.135,1.667 1.927,2.344 false 0.135,0.083 0.417,0.271 0.281,0.188 10 false *a 0.135,2.635 0.417,2.823 0.281,0.188 10 false *b 2.729,2.344 2.969,2.521 0.24,0.177 10 false E1 1.698,2.344 2.135,2.521 0.438,0.177 10 false PCON 2.875,3.625 3.208,3.802 0.333,0.177 10 false GND 2.104,0.417 2.396,0.583 0.292,0.167 10 false A24

Connect an oscilloscope between the transmission control ECU assembly terminals specified in the table below, and measure the waveform.

Item Contents
Symbols A24-22 (PCON) - A24-1 (E1)
Tool setting 10 V/DIV., 10 msec./DIV.
Vehicle condition Power switch on (IG)

OK:

The waveform is similar to that shown in the illustration.


Text in Illustration
*a Component with harness connected
(Transmission Control ECU Assembly)
*b Waveform

HINT:

Perform this inspection with the connector connected.



c.

Turn the power switch off.



OK

REPLACE TRANSMISSION CONTROL ECU ASSEMBLY

NG

2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
2.CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL ECU ASSEMBLY - POWER MANAGEMENT CONTROL ECU)
a.

Disconnect the A24 transmission control ECU assembly connector.


b.

Disconnect the A22 power management control ECU connector.


c.
U154760E01
0.118,0.102 0.403,0.291 0.286,0.188 10 *a 0.118,2.292 0.403,2.480 0.286,0.188 10 *b 2.347,1.892 2.771,2.066 0.424,0.174 10 PCON 2.262,3.894 2.686,4.068 0.424,0.174 10 PCON 1.588,0.203 1.880,0.370 0.292,0.167 10 A24 1.26,2.379 1.552,2.546 0.292,0.167 10 A22 1.838,1.449 2.302,1.914 false 1.607,4.117 2.245,3.963 false

Measure the resistance according to the value(s) in the table below.

Standard Resistance (Check for Open):
Tester Connection Condition Specified Condition
A24-22 (PCON) - A22-22 (PCON) Power switch off Below 1 Ω


Standard Resistance (Check for Short):
Tester Connection Condition Specified Condition
A24-22 (PCON) or A22-22 (PCON) - Body ground and other terminals Power switch off 10 kΩ or higher


Text in Illustration
*a Front view of wire harness connector
(to Transmission Control ECU Assembly)
*b Rear view of wire harness connector
(to Power Management Control ECU)


d.

Connect the A22 power management control ECU connector.


e.

Connect the A24 transmission control ECU assembly connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR