Home › Drivetrain › P410 (HYBRID TRANSMISSION / TRANSAXLE) › ELECTRONIC SHIFT LEVER SYSTEM › 2012.10–2014.11
RM2070E _52 Drivetrain _061915 P410 HYBRID TRANSMISSION / TRANSAXLE _0301645 ELECTRONIC SHIFT LEVER SYSTEM C

P410 HYBRID TRANSMISSION / TRANSAXLE  ELECTRONIC SHIFT LEVER SYSTEM  C2315  HV System  


DESCRIPTION

The transmission control ECU assembly receives a P position switch signal from the power management control ECU and activates the parking lock motor by controlling current, causing the parking lock mechanism to switch. When the power management control ECU detects a malfunction with the P position switch (transmission shift main switch) or P position signal, it sends an information signal to the transmission control ECU assembly. After receiving this signal, the transmission control ECU assembly stores this DTC.

DTC No. DTC Detection Condition Trouble Area
C2315 With the power switch on (IG) (IG circuit malfunction is not detected), a malfunction signal is received from the power management control ECU for 2 seconds or more. Power management control ECU

WIRING DIAGRAM

C351651E01
2.063,1.094 2.531,1.333 0.469,0.24 10 false PCON 2.073,1.938 2.542,2.177 0.469,0.24 10 false PPOS 2.573,0.979 3.042,1.219 0.469,0.24 10 false 22 2.573,1.813 3.042,2.052 0.469,0.24 10 false 28 4.542,1.823 5.01,2.063 0.469,0.24 10 false 23 4.344,2.51 4.813,2.75 0.469,0.24 10 false A24 4.344,2.677 6.885,2.938 2.542,0.26 10 false Transmission Control ECU Assembly 0.927,2.521 1.396,2.76 0.469,0.24 10 false A22 0.927,2.688 3.563,3.063 2.635,0.375 10 false Power Management Control ECU 4.802,1.927 5.271,2.167 0.469,0.24 10 false PPOS 4.813,1.094 5.281,1.333 0.469,0.24 10 false PCON 4.563,0.979 5.031,1.219 0.469,0.24 10 false 22

PROCEDURE

1.CHECK DTC OUTPUT (HYBRID CONTROL)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Powertrain / Hybrid Control / Trouble Codes.


d.

Check if DTCs are output.

Result:
Result Proceed to
The following DTCs are not output. A
Any of the following DTCs are output. B


DTC No. Relevant Diagnosis
P0851-579 Park/Neutral Switch Input Circuit Low
P0852-580 Park/Neutral Switch Input Circuit High
P085D-599 Gear Shift Control Module "A" Performance
P0861-597 Gear Shift Control Module "A" Communication Circuit Low
P0862-598 Gear Shift Control Module "A" Communication Circuit High
U1107-436 Lost Communication with Power Management Module


e.

Turn the power switch off.



A

2.CLEAR DTC

B

2.CLEAR DTC
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Enter the following menus: Body Electrical / Transmission Control / Trouble Codes.


d.

Read and record the DTCs and freeze frame data.


e.

Clear DTCs and freeze frame data.


f.

Turn the power switch off.



NEXT

3.CHECK DTC OUTPUT (HEALTH CHECK)
3.CHECK DTC OUTPUT (HEALTH CHECK)
a.

Connect the GTS to the DLC3.


b.

Turn the power switch on (IG).


c.

Wait for 2 seconds or more.


d.

Enter the following menus: System Select / Health Check.


e.

Check if DTCs are output.

Result:
Result Proceed to
DTC is not output. A
DTC C2315 only is output. B
DTC C2315 and other DTCs are output together. C


HINT:

DTC C2315 only may be output when the P position switch (transmission shift main switch) connector is disconnected and reconnected.



f.

Turn the power switch off.



A

END

B

C

GO TO DTC CHART