Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM2070E _52 Drivetrain _061916 DRIVE SHAFT / PROPELLER SHAFT _0301657 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  DISASSEMBLY  


PROCEDURE

Hide 43448G 1.SEPARATE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

a.
C205158

Using a screwdriver, release the staked part of the front No. 2 axle inboard joint boot clamp and separate the front No. 2 axle inboard joint boot clamp as shown in the illustration.


Hide 43448F 2.SEPARATE FRONT AXLE INBOARD JOINT BOOT CLAMP

HINT:

Perform the same procedure as for the front No. 2 axle inboard joint boot clamp.


Hide 3.SEPARATE INBOARD JOINT BOOT

a.

Separate the inboard joint boot from the front drive inboard joint assembly.


Hide 43040 4.REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY

a.

Remove the old grease from the front drive inboard joint assembly.


b.
C158439E05
0.948,0.387 1.115,0.548 0.167,0.161 10 *a 1.404,1.258 1.144,0.49 1.144,0.49 1.951,0.659 false

Put matchmarks on the front drive inboard joint assembly and front axle outboard joint shaft assembly.

Text in Illustration
*a Matchmark

NOTICE:

Do not use a punch for the marks.



c.

Remove the front drive inboard joint assembly from the front axle outboard joint shaft assembly.


d.

Secure the front axle outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



e.
F045046

Using a snap ring expander, remove the shaft snap ring from the front axle outboard joint shaft assembly.


f.
C141145E29
1.607,1.725 1.791,1.881 0.184,0.156 10 *a 2.89,1.025 1.72,1.705 1.72,1.705 2.932,1.111 false

Put matchmarks on the front axle outboard joint shaft assembly and tripod joint.

Text in Illustration
*a Matchmark

NOTICE:

Do not use a punch for the marks.



g.

Using a brass bar and a hammer, tap out the tripod joint from the front axle outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Do not drop the tripod joint.




h.

Remove the front No. 2 axle inboard joint boot clamp, inboard joint boot and front axle inboard joint boot clamp.


i.
U110972

Remove the front axle inboard joint grommet from the front drive inboard joint assembly.


Hide 43474G 5.SEPARATE FRONT DRIVE SHAFT DAMPER CLAMP (w/ 1 Clamp)

a.
U110951E03
2.094,3.021 2.115,3.042 0.021,0.021 2.021,3.104 2.042,3.125 0.021,0.021 2.094,3.177 2.115,3.198 0.021,0.021 2.167,3.104 2.188,3.125 0.021,0.021 2.917,2.865 2.938,2.885 0.021,0.021 2.844,2.948 2.865,2.969 0.021,0.021 2.917,3.021 2.938,3.042 0.021,0.021 2.99,2.948 3.01,2.969 0.021,0.021 0.115,0.073 1.51,0.302 1.396,0.229 10 false *A 0.073,2.115 2,2.344 1.927,0.229 10 false *B

for One Touch Type:

i.

Using a screwdriver, release the staked part of the front drive shaft damper clamp and separate the front drive shaft damper clamp as shown in the illustration.

Text in Illustration
*A for One Touch Type
*B for Claw Engagement Type



b.

for Claw Engagement Type:

i.

Using needle-nose pliers, disengage the 2 claws and remove the front drive shaft damper clamp as shown in the illustration.



Hide 43474F 6.SEPARATE FRONT DRIVE SHAFT DAMPER CLAMP (w/ 2 Clamps)

a.

for Type A:

i.
C388203C02
1.021,0.865 1.125,1.083 1.125,1.083 1.625,1 false 0.104,0.135 0.417,0.333 0.313,0.198 10 false *A 0.083,2.677 0.396,2.875 0.313,0.198 10 false *B 1.021,1.094 1.333,1.292 0.313,0.198 10 false *a
*A for Type A
*B for Type B
*a Claw


Using needle-nose pliers, disengage each claw on each front drive shaft damper clamp, and then separate each clamp as shown in the illustration.



b.

for Type B:

i.

Using needle-nose pliers, separate the 2 front drive shaft damper clamps as shown in the illustration.



Hide 43474E 7.REMOVE FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)

a.

Remove the front drive shaft damper and front drive shaft damper clamp from the front axle outboard joint shaft assembly.


Hide 43474D 8.REMOVE FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)

a.

Remove the front drive shaft damper and 2 front drive shaft damper clamps from the front axle outboard joint shaft assembly.


Hide 43447F 9.SEPARATE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

a.
C205159

Using a screwdriver, release the staked part of the front No. 2 axle outboard joint boot clamp and separate the front No. 2 axle outboard joint boot clamp as shown in the illustration.


Hide 43447E 10.SEPARATE FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

HINT:

Perform the same procedure as for the front No. 2 axle outboard joint boot clamp.


Hide 11.REMOVE OUTBOARD JOINT BOOT (for LH Side)

a.

Remove the front axle outboard joint boot clamp, outboard joint boot and front No. 2 axle outboard joint boot clamp from the front axle outboard joint shaft assembly.


b.

Remove the old grease from the outboard joint.


Hide 41336E 12.REMOVE FRONT DRIVE SHAFT DUST COVER

a.
F040647E40
1.969,0.844 2.427,0.385 false 2.458,0.25 2.792,0.417 0.333,0.167 10 false SST

Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly.

SST
09950-00020  

NOTICE:

Do not drop the front drive inboard joint assembly.