Home › Drivetrain › DRIVE SHAFT / PROPELLER SHAFT › FRONT DRIVE SHAFT ASSEMBLY
RM2070E _52 Drivetrain _061916 DRIVE SHAFT / PROPELLER SHAFT _0301657 FRONT DRIVE SHAFT ASSEMBLY A

DRIVE SHAFT / PROPELLER SHAFT  FRONT DRIVE SHAFT ASSEMBLY  REASSEMBLY  


PROCEDURE

Hide 41336E 1.INSTALL FRONT DRIVE SHAFT DUST COVER (for LH Side)

a.
F041033E31
0.583,0.646 0.583,0.333 0.583,0.333 0.458,0.333 false 0.146,0.25 0.479,0.438 0.333,0.188 10 false SST

Using SST and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.

SST
09527-10011  

NOTICE:
·

Install the front drive shaft dust cover in the correct direction.

·

Do not deform the front drive shaft dust cover.




Hide 41336D 2.INSTALL FRONT DRIVE SHAFT DUST COVER (for RH Side)

a.
C157559E01
0.047,0.304 0.353,0.462 0.306,0.158 10 SST 0.741,0.72 0.549,0.388 0.549,0.388 0.404,0.388 false

Using SST and a press, install a new front drive shaft dust cover into the front drive inboard joint assembly until it is flush with the end.

SST
09527-10011  

NOTICE:
·

Install the front drive shaft dust cover in the correct direction.

·

Do not deform the front drive shaft dust cover.




Hide 3.INSTALL OUTBOARD JOINT BOOT (for LH Side)

a.
C127681E14
2.467,0.402 3.153,0.567 0.686,0.165 10 *a 2.41,0.481 2.096,0.481 false 2.096,0.481 1.758,0.752 false

Wrap the splines of the front axle outboard joint shaft assembly with protective tape to prevent the boot from being damaged.

Text in Illustration
*a Protective Tape


b.
U154675E02
1.656,1.479 1.656,1.823 false 2.365,1.833 2.365,1.438 false 2.99,1.823 2.99,1.219 false 1.094,1.833 1.094,1.417 false 2.292,1.844 2.448,2.021 0.156,0.177 10 false *3 2.927,1.833 3.083,2.01 0.156,0.177 10 false *4 1.583,1.844 1.74,2.021 0.156,0.177 10 false *2 1.021,1.854 1.177,2.031 0.156,0.177 10 false *1

Install new parts onto the front axle outboard joint shaft assembly in the following order:

Text in Illustration
*1 Front Axle Outboard Joint Shaft Assembly
*2 Front No. 2 Axle Outboard Joint Boot Clamp
*3 Outboard Joint Boot
*4 Front Axle Outboard Joint Boot Clamp
V100135

Outboard Joint Side
V100136

Inboard Joint Side

i.

Front No. 2 axle outboard joint boot clamp


ii.

Outboard joint boot


iii.

Front axle outboard joint boot clamp



c.

Pack the joint portion of the front axle outboard joint shaft assembly and outboard joint boot with grease.

Standard grease capacity:

135 to 145 g (4.76 to 5.11 oz.)



d.

Install the outboard joint boot onto the front axle outboard joint shaft assembly groove.

NOTICE:
·

Do not allow grease to adhere to the boot clamp track of the outboard joint boot.

·

Keep the inside of the outboard joint boot free of foreign matter.




Hide 43447F 4.INSTALL FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C415871C01
2.156,1.5 2.677,1.5 false 0.833,1.24 1.354,1.24 false 1.917,2.031 2.438,2.031 false 2.708,1.438 3.021,1.594 0.313,0.156 10 false *a 0.667,1.177 0.979,1.333 0.313,0.156 10 false *b 1.729,1.948 2.042,2.104 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Install the front No. 2 axle outboard joint boot clamp to the outboard joint boot and temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Set the lever to the guide groove correctly and install the clamp as far to the inside of the vehicle as possible.

·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




b.

As shown in the illustration, while pressing the outboard joint area against the work surface, firmly press the lever into place by rolling the outboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415872C01
3.604,1.052 3.135,1.406 3.135,1.406 3.708,1.042 true 2.083,1.49 1.594,1.49 true 1.958,2.281 1.688,2.281 1.688,2.281 1.448,1.906 true 5.927,2.229 5.646,1.938 5.646,1.938 5.49,1.938 true 3.823,0.292 4.135,0.448 0.313,0.156 10 false *a 4.104,1.302 4.417,1.458 0.313,0.156 10 false *b 5.24,0.583 5.552,0.74 0.313,0.156 10 false *c 2.979,1.354 3.292,1.51 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.417 1.74,1.573 0.313,0.156 10 false *d 2.01,2.219 2.323,2.375 0.313,0.156 10 false *e 5.281,1.875 5.594,2.031 0.313,0.156 10 false *d
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Do not damage the deflector.

·

Make sure that the outboard joint is in direct contact with the work surface.




c.
C233614

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the outboard joint boot.



Hide 43447E 5.INSTALL FRONT AXLE OUTBOARD JOINT BOOT CLAMP (for LH Side)

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C107948

Install the front axle outboard joint boot clamp onto the outboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356E08
2.476,0.872 2.664,1.052 0.188,0.180 10 *a

Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.

Text in Illustration
*a Place the tip near the center of the lever.


c.
C327546

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the outboard joint boot.



Hide 43474E 6.INSTALL FRONT DRIVE SHAFT DAMPER (w/ 1 Clamp)

a.
C171727E07
1.671,0.353 1.894,0.513 0.222,0.160 10 (A)

Install the front drive shaft damper onto the front axle outboard joint shaft assembly as shown in the illustration.

Dimension (A):

161 to 165 mm (6.34 to 6.49 in.)



Hide 43474D 7.INSTALL FRONT DRIVE SHAFT DAMPER (w/ 2 Clamps)

a.
C315780E01
0.156,2.43 0.493,2.670 0.336,0.239 10 *B 0.156,0.024 0.493,0.263 0.336,0.239 10 *A 1.488,0.308 1.825,0.547 0.336,0.239 10 (A) 1.471,3.78 1.808,4.019 0.336,0.239 10 (A)

Temporarily install the front drive shaft damper and 2 new front drive shaft damper clamps to the front axle outboard joint shaft assembly as shown in the illustration.

Text in Illustration
*A for LH Side
*B for RH Side

Dimension (A)
for LH Side 211.7 to 215.7 mm (8.33 to 8.49 in.)
for RH Side 488 to 492 mm (1.602 to 1.614 ft.)


Hide 43474G 8.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (w/ 1 Clamp)

a.

Secure the front axle outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.

for One Touch Type:

i.
C225243E01
0.114,0.089 0.312,0.251 0.198,0.161 10 *A 0.114,2.408 0.312,2.570 0.198,0.161 10 *B

Using a screwdriver, install a new front drive shaft damper clamp, as shown in the illustration.

Text in Illustration
*A for One Touch Type
*B for Claw Engagement Type



c.

for Claw Engagement Type:

i.

Using needle-nose pliers, install a new front drive shaft damper clamp, as shown in the illustration.



Hide 43474F 9.INSTALL FRONT DRIVE SHAFT DAMPER CLAMP (w/ 2 Clamps)

a.

Secure the front axle outboard joint shaft assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.



b.
C388203C01
1.021,0.865 1.125,1.083 1.125,1.083 1.625,1 false 0.104,0.135 0.417,0.333 0.313,0.198 10 false *A 0.083,2.677 0.396,2.875 0.313,0.198 10 false *B 1.021,1.094 1.333,1.292 0.313,0.198 10 false *a
*A for Type A
*B for Type B
*a Claw


for Type A:

i.

Using needle-nose pliers, engage each claw to install the 2 front drive shaft damper clamps as shown in the illustration.



c.

for Type B:

i.

Using needle-nose pliers, install the 2 front drive shaft damper clamps as shown in the illustration.



Hide 43040 10.INSTALL FRONT DRIVE INBOARD JOINT ASSEMBLY

a.
U113913E09
0.688,1.75 0.688,1.323 false 1.521,1.719 1.521,1.469 false 2.49,1.76 2.49,1.677 false 2.917,1.729 2.917,1.24 false 2.833,1.75 3.031,1.938 0.198,0.188 10 false *4 2.417,1.771 2.615,1.958 0.198,0.188 10 false *3 1.438,1.74 1.635,1.927 0.198,0.188 10 false *2 0.615,1.771 0.813,1.958 0.198,0.188 10 false *1

Install new parts onto the front axle outboard joint shaft assembly in the following order:

Text in Illustration
*1 Front Axle Inboard Joint Boot Clamp
*2 Inboard Joint Boot
*3 Front No. 2 Axle Inboard Joint Boot Clamp
*4 Protective Tape
V100135

Outboard Joint Side
V100136

Inboard Joint Side

i.

Front axle inboard joint boot clamp


ii.

Inboard joint boot


iii.

Front No. 2 axle inboard joint boot clamp



b.

Secure the front axle outboard joint shaft assembly in a vise using aluminum plates.

NOTICE:

Do not overtighten the vise.



c.

Remove the protective tape.


d.
C067417E53
1.26,1.719 1.979,1.719 1.979,1.719 1.75,1.438 false 2.021,1.677 2.188,1.823 0.167,0.146 10 false *a

Align the matchmarks and install the tripod joint onto the front axle outboard joint shaft assembly as shown in the illustration.

Text in Illustration
*a Matchmark

NOTICE:

Face the serrated side of the tripod joint outward and install it onto the outboard joint end.



e.

Using a brass bar and a hammer, install the tripod joint to the front axle outboard joint shaft assembly.

NOTICE:
·

Do not tap the rollers.

·

Keep the tripod joint free of foreign matter.




f.
F045046

Using a snap ring expander, install a new shaft snap ring to the front axle outboard joint shaft assembly.


g.

Pack the front drive inboard joint assembly and inboard joint boot with grease.

Standard grease capacity:

168 to 178 g (5.92 to 6.27 oz.)



h.
C164752E03
2.544,1.375 2.544,1.599 2.544,1.599 2.43,1.599 false 2.234,1.502 2.405,1.655 0.171,0.153 10 *a

Install a new front axle inboard joint grommet onto the inboard joint groove.

Text in Illustration
*a Groove

NOTICE:

Securely fit the protrusion on the inboard joint grommet into the inboard joint groove.



i.
C158439E05
0.948,0.387 1.115,0.548 0.167,0.161 10 *a 1.404,1.258 1.144,0.49 1.144,0.49 1.951,0.659 false

Align the matchmarks and install the front drive inboard joint assembly onto the front axle outboard joint shaft assembly.

Text in Illustration
*a Matchmark


Hide 11.INSTALL INBOARD JOINT BOOT

a.

Install the inboard joint boot into the grooves of the inboard joint grommet and front axle outboard joint shaft assembly.

NOTICE:

Keep the grooves free of grease.



Hide 43448F 12.INSTALL FRONT AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.
C107948

Install the front axle inboard joint boot clamp onto the inboard joint boot and temporarily fold back the lever.

NOTICE:
·

Set the lever into the guide groove correctly.

·

Check the band and the lever for any deformation before folding back the lever.




b.
C158356E08
2.476,0.872 2.664,1.052 0.188,0.180 10 *a

Using water pump pliers, pinch the front axle outboard joint boot clamp to temporarily secure it.

Text in Illustration
*a Place the tip near the center of the lever.


c.
C327546

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the inboard joint boot.



Hide 43448G 13.INSTALL FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP

CAUTION:

Wear protective gloves. Sharp areas on the parts may injure your hands.


a.

Install the boot clamp onto the inboard joint boot.


b.
C157783E16
1.5,1.635 1.771,1.823 0.271,0.188 10 false (A)

Adjust dimension (A) until it is within the specified length.

Dimension (A)
LH Side RH Side
556.2 mm (1.82 ft.) 905.2 mm (2.97 ft.)


c.
C296186C01
0.74,0.948 1.073,0.948 true 2.302,0.958 2.635,0.958 true 1.76,1.885 1.76,2.042 1.76,2.042 2.115,2.042 true 1.094,2.49 1.573,2.792 true 0.677,0.313 0.99,0.469 0.313,0.156 10 false *1 0.573,0.854 0.885,1.01 0.313,0.156 10 false *a 2.667,0.865 2.979,1.021 0.313,0.156 10 false *a 2.135,1.948 2.448,2.104 0.313,0.156 10 false *a 0.927,2.385 1.24,2.542 0.313,0.156 10 false *a
*1 Front Axle Inboard Joint Grommet
*a Recessed Parts


While keeping dimension (A) within the specified length, equalize the pressure within the inboard joint with atmospheric pressure by slightly lifting one of the recessed areas of the front axle inboard joint grommet from the front drive inboard joint assembly.


d.
C415868C01
1.896,0.823 2.375,0.625 false 0.615,0.302 0.927,0.458 0.313,0.156 10 false *1 0.583,1.625 0.896,1.781 0.313,0.156 10 false *2 2.406,0.542 2.719,0.698 0.313,0.156 10 false *a 1.677,1.344 1.99,1.5 0.313,0.156 10 false B 0.76,2.938 1.073,3.094 0.313,0.156 10 false B 2.583,2.969 2.896,3.125 0.313,0.156 10 false B
*1 Front No. 2 Axle Inboard Joint Boot Clamp
*2 Front Axle Inboard Joint Grommet
*a Fulcrum Point


Set the lever fulcrum point at any point (B) indicated in the illustration.

NOTICE:
·

Perform this work with the inside of the inboard joint kept at atmospheric pressure.

·

Set the lever into the guide groove correctly and install the clamp as far into the inside of the vehicle as possible.




e.
C415869C01
2.156,1.542 2.656,1.542 false 0.781,1.135 1.281,1.135 false 1.979,2.073 2.479,2.073 false 2.708,1.469 3.021,1.625 0.313,0.156 10 false *a 0.615,1.063 0.927,1.219 0.313,0.156 10 false *b 1.792,1.99 2.104,2.146 0.313,0.156 10 false *c
*a Fulcrum Point
*b Lever Push Position
*c Band Support Position


Temporarily fold back the lever at the fulcrum point.

NOTICE:
·

Check the band and the lever for any deformation before folding back the lever.

·

The lever folds easily at the fulcrum point when pushed at the position shown in the illustration.

·

When folding back the lever, do not push at the end of the lever.

C415873C01
6.771,1.49 6.125,1.49 true 5.948,1.417 6.26,1.573 0.313,0.156 10 false *a
*a Temporary Claw - -


·

If the lever bends in the middle, it may not engage with the temporary claws or may not be held in the correct position.




f.

As shown in the illustration, while pressing the inboard joint area against the work surface, firmly press the lever into place by rolling the inboard joint area forward from the folded fulcrum point to the temporary claw area until a click sound is heard.

C415870C01
3.615,1.104 3.365,1.698 3.365,1.698 3.719,1.083 true 2.083,1.49 1.594,1.49 true 5.927,2.219 5.76,1.917 5.76,1.917 5.531,1.917 true 1.885,2.292 1.604,2.292 1.604,2.292 1.365,1.875 true 3.823,0.302 4.135,0.458 0.313,0.156 10 false *a 4.073,1.333 4.385,1.49 0.313,0.156 10 false *b 5.219,0.698 5.531,0.854 0.313,0.156 10 false *c 3.25,1.719 3.563,1.875 0.313,0.156 10 false *d 1.208,2.365 1.521,2.521 0.313,0.156 10 false *b 1.427,1.406 1.74,1.563 0.313,0.156 10 false *d 5.354,1.844 5.667,2 0.313,0.156 10 false *d 1.938,2.25 2.25,2.406 0.313,0.156 10 false *e
*a Press down *b Contact Point
*c Roll forward *d Temporary Claw
*e Fulcrum Point - -


NOTICE:
·

Make sure that the inboard joint is in direct contact with the work surface.

·

Do not damage the front drive shaft dust cover.




g.
C158764

Using a plastic hammer, tap the buckle to secure it while adjusting the clearance between the lever and the groove to make the clearance between the buckle edge and the lever end even.

NOTICE:

Do not damage the inboard joint boot.