Home › Suspension › ALIGNMENT / HANDLING DIAGNOSIS › REAR WHEEL ALIGNMENT › 2014.11–2016.05
RM2070E _53 Suspension _061918 ALIGNMENT / HANDLING DIAGNOSIS _0301665 REAR WHEEL ALIGNMENT G

ALIGNMENT / HANDLING DIAGNOSIS  REAR WHEEL ALIGNMENT  INSPECTION  


CAUTION / NOTICE / HINT

NOTICE:

If the wheel alignment has been adjusted, or if suspension or underbody components have been removed/installed or replaced, be sure to perform the following initialization procedure in order for the system to function normally:

Perform zero point calibration of the yaw rate and acceleration sensor.



PROCEDURE

Hide 3.INSPECT CAMBER

NOTICE:

Inspect while the vehicle is unloaded.


a.

Install a camber-caster-kingpin gauge.


b.

Inspect the camber.

Camber (Unloaded Vehicle):
Camber Inclination Right-left Difference
-1°26' +/- 0°30' (-1.43° +/- 0.50°)
-1°24' +/- 0°30' (-1.40° +/- 0.50°) *1
0°30' (0.50°) or less


*1: ZVW40R-AWXEBQ

HINT:

Camber is not adjustable. If the measurement is not within the specified range, inspect the suspension parts for damage and/or wear, and replace them if necessary.



Hide 4.INSPECT TOE-IN

NOTICE:

Inspect while the vehicle is unloaded.


a.

Bounce the vehicle up and down at the corners to stabilize the suspension.


b.

Release the parking brake and move the shift lever to N.


c.

Push the vehicle straight ahead approximately 5 m (16.4 ft.). (Step A)


d.
C188968E31
0.823,0.604 0.823,1.135 false 1.365,0.604 1.365,1.01 1.365,1.01 0.833,1.01 false 2.521,1.333 2.521,1.667 false 0.74,1.135 0.917,1.302 0.177,0.167 10 false *a 2.427,1.698 2.604,1.854 0.177,0.156 10 false *b

Put tread center marks on the rearmost points of the rear wheels and measure the distance between the marks (dimension B).

Text in Illustration
*a Tread Center Mark
*b Dimension B
V100135

Front of the Vehicle


e.

Slowly push the vehicle straight ahead to cause the rear wheels to rotate 180°. Use the rear tire valve as a reference point.

HINT:

Do not allow the wheels to rotate more than 180°. If the wheels rotate more than 180°, perform the procedure from Step A again.



f.
C188969E25
0.647,1.275 0.647,1.636 false 1.912,0.543 2.051,0.704 0.14,0.16 10 C 3.071,0.55 3.21,0.71 0.14,0.16 10 D 2.498,0.717 2.638,0.877 0.14,0.16 10 A 2.509,1.537 2.649,1.698 0.14,0.16 10 B 0.563,1.655 0.735,1.815 0.172,0.16 10 *a

Measure the distance between the tread center marks on the front of the wheels (dimension A).

Text in Illustration
*a Dimension A
V100135

Front of the Vehicle

Toe-in (Unloaded Vehicle):
Tire Size Specified Condition Right-left Difference
205/60R16 C + D: 0°13' +/- 0°17' ( 0.22° +/- 0.29°)
C + D: 0°08' +/- 0°17' ( 0.14° +/- 0.29°) *1
0°45' (0.75°) or less
B - A: 2.3 +/- 3.0 mm (0.0906 +/- 0.118 in.)
B - A: 1.4 +/- 3.0 mm (0.0551 +/- 0.118 in.) *1
-
215/50R17 C + D: 0°14' +/- 0°17' ( 0.23° +/- 0.29°) 0°45' (0.75°) or less
B - A: 2.4 +/- 3.0 mm (0.0945 +/- 0.118 in.) -


*1: ZVW40R-AWXEBQ

HINT:

Measure "B - A" only when "C + D" cannot be measured.


If the toe-in is not within the specified range, inspect the suspension parts and replace them if necessary.