Home › Suspension › REAR SUSPENSION › REAR SHOCK ABSORBER › 2012.03–2014.11
RM2070E _53 Suspension _061920 REAR SUSPENSION _0301673 REAR SHOCK ABSORBER A

REAR SUSPENSION  REAR SHOCK ABSORBER  INSTALLATION  


CAUTION / NOTICE / HINT

HINT:
·

Use the same procedure for the RH side and LH side.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 48341B 1.INSTALL REAR NO. 1 SPRING BUMPER

a.

Install the rear No. 1 spring bumper to the rear shock absorber assembly.


Hide 48540 2.TEMPORARILY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.

Insert the upper end of the rear shock absorber assembly with the rear No. 1 spring bumper to the vehicle body.


b.

Temporarily tighten the rear shock absorber assembly to the rear axle beam assembly with the bolt and nut.

NOTICE:

Since the stopper nut is used, turn the bolt.


HINT:

Insert the bolt with the threaded end facing the outside of the vehicle.



Hide 48755 3.INSTALL REAR SUSPENSION SUPPORT

a.
C241186E03
0.958,1.996 1.138,2.148 0.180,0.152 10 *a 2.316,1.996 2.496,2.148 0.180,0.152 10 *b

Install the rear suspension support.

Text in Illustration
*a Correct
*b Incorrect

NOTICE:

Make sure that the rear suspension support is correctly installed as shown in the illustration.



Hide 48530B 4.INSTALL REAR NO. 1 SHOCK ABSORBER CUSHION WASHER

a.
C236498

Install the rear No. 1 shock absorber cushion washer.

Text in Illustration
V100135

Upper Side
V100136

Lower Side

NOTICE:

Be sure to install the rear No. 1 shock absorber cushion washer in the correct direction.



b.

Apply a few drops of adhesive to the threads of a new nut.

Adhesive:

Toyota genuine adhesive 1324, three bond 1324 or equivalent



c.

Using a union nut wrench, fully tighten the lock nut while holding the rod of the rear shock absorber assembly with a hexagon wrench.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

NOTICE:
·

Securely insert the hexagon wrench to the rear shock absorber rod to prevent damage to the rear shock absorber assembly when tightening the nut.

·

Use the formula to calculate special torque values for situations where the union nut wrench is combined with a torque wrench (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).




Hide 64715C 5.INSTALL DECK SIDE TRIM COVER

a.

Engage the 6 claws to install the deck side trim cover.


Hide 89407A 6.INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

Hide 7.INSTALL REAR WHEEL

Torque:
103 N*m (1050 kgf*cm, 76 ft.*lbf)

Hide 8. STABILIZE SUSPENSION

a.

Lower the vehicle.


b.

Bounce the vehicle up and down several times to stabilize the suspension.


Hide 48540 9.FULLY TIGHTEN REAR SHOCK ABSORBER ASSEMBLY

a.
C236501

Fully tighten the bolt.

Torque:
90 N*m (918 kgf*cm, 66 ft.*lbf)

NOTICE:
·

Since the stopper nut is used, turn the bolt.

·

The final torque must be applied under the standard vehicle height conditions.




Hide 10. INITIALIZE HEIGHT CONTROL SENSOR SIGNAL (w/ Height Control Sensor)

Hide 11.ADJUST HEADLIGHT AIMING (w/ Height Control Sensor)