Home › Suspension › REAR SUSPENSION › REAR COIL SPRING
RM2070E _53 Suspension _061920 REAR SUSPENSION _0301674 REAR COIL SPRING A

REAR SUSPENSION  REAR COIL SPRING  REMOVAL  


PROCEDURE

Hide 1.REMOVE REAR WHEELS

Hide 89516D 2.DISCONNECT SKID CONTROL SENSOR WIRE LH

Hide 89516C 3.DISCONNECT SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 89516D 4.SEPARATE SKID CONTROL SENSOR WIRE LH

a.
C207255

Remove the nut and separate the 2 clamps and skid control sensor wire LH.


Hide 89516C 5.SEPARATE SKID CONTROL SENSOR WIRE RH

HINT:

Perform the same procedure as the LH side.


Hide 89407A 6.SEPARATE REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY (w/ Height Control Sensor)

a.
C207241

Remove the bolt and separate the rear height control sensor sub-assembly from the rear axle beam assembly.


b.
C207242E03
1.604,1.219 1.604,1.594 false 1.521,1.604 1.698,1.76 0.177,0.156 10 true *1

Using a vinyl tape, secure the rear height control sensor sub-assembly as shown in the illustration.

Text in Illustration
*1 Vinyl Tape


Hide 65638 7.SEPARATE REAR WHEEL HOUSE LINER LH

a.
C236502

Remove the clip and turn back the rear wheel house liner LH to separate the rear wheel house liner LH.


Hide 65637 8.SEPARATE REAR WHEEL HOUSE LINER RH

HINT:

Perform the same procedure as the LH side.


Hide 48231B 9.REMOVE REAR COIL SPRING LH

a.
C236503E04
0.052,0.01 0.344,0.25 0.292,0.24 10 true *A 0.052,2.25 0.229,2.406 0.177,0.156 10 false *B

Loosen the 2 bolts.

Text in Illustration
*A LH Side
*B RH Side

NOTICE:

Do not remove the bolts.



b.

Support the spring seat of the rear axle beam assembly using 2 jacks and 2 wooden blocks.

C236504E02
2.021,2.24 2.521,2.24 false 1.885,2.479 2.531,2.479 false 4.625,2.229 5.104,2.229 false 4.615,2.458 5.229,2.458 false 2.552,2.167 2.719,2.302 0.167,0.135 10 false *1 2.563,2.396 2.729,2.531 0.167,0.135 10 false *2 4.458,2.146 4.667,2.323 0.208,0.177 10 false *1 4.448,2.375 4.615,2.51 0.167,0.135 10 false *2

Text in Illustration
*1 Wooden Block *2 Jack

CAUTION:

Do not jack up the rear axle beam assembly too high as the vehicle may fall.


HINT:

Support the rear shock absorber at a position where it compresses by approximately 20 to 30 mm (0.787 to 1.18 in.).



c.

Remove the 2 bolts while holding the 2 nuts and separate the rear axle beam assembly from the rear shock absorber assemblies LH and RH.

NOTICE:

Since the stopper nuts are used, turn the bolts.



d.
C236505

Slowly lower the rear axle beam assembly using 2 jacks and 2 wooden blocks, and remove the rear coil spring LH.

NOTICE:

When moving the rear axle beam assembly beyond full rebound, make sure that the rear axle beam assembly is within 35° of the standard position, and is not out of position for more than 10 minutes.



e.

Slowly jack up the rear axle beam assembly using 2 jacks and 2 wooden blocks, and temporarily tighten the rear axle beam assembly to the rear shock absorber assemblies LH and RH with the 2 bolts and 2 nuts.

C236506E02
2.042,2.229 2.552,2.229 false 1.906,2.458 2.552,2.458 false 4.594,2.219 5.115,2.219 false 4.594,2.448 5.24,2.448 false 2.583,2.167 2.74,2.313 0.156,0.146 10 false *1 2.583,2.385 2.74,2.531 0.156,0.146 10 false *2 4.438,2.146 4.594,2.292 0.156,0.146 10 false *1 4.438,2.375 4.594,2.521 0.156,0.146 10 false *2

Text in Illustration
*1 Wooden Block *2 Jack

NOTICE:

Since the stopper nuts are used, turn the bolts.



Hide 48231A 10.REMOVE REAR COIL SPRING RH

HINT:

Perform the same procedure as the LH side.


Hide 48259A 11.REMOVE REAR UPPER COIL SPRING INSULATOR LH

Hide 48257C 12.REMOVE REAR UPPER COIL SPRING INSULATOR RH

Hide 48258C 13.REMOVE REAR LOWER COIL SPRING INSULATOR LH

Hide 48258B 14.REMOVE REAR LOWER COIL SPRING INSULATOR RH